Instruction/ maintenance manual of the product FR2 Series Hatco
Go to page of 16
HYDRO-HEA TER Food Rethermalizers/Hot Food T able Heater FR2 Series Inst allation & Operating Manual I&W #07.05.143.00 This manual contains import ant safety information concerning the maintenance, use and operation of this product. Failure to follow the instructions contained in this manual may result in serious injury .
i INTRODUCTION Hatco FR2 Hydro-Heater Food Rethermalizers/Hot Food T able Heaters are designed to supply temperature-controlled water to a holding vessel (sink or tank) located above the heater .
CAUTIONS W ater in the unit and holding vessel is very hot. Wear protective gloves and proper attire when operating to avoid injury . Do not use extension pipes on the inlet and outlet connections on heater unit s. Poor performance or unsafe conditions may occur .
MODEL DESCRIPTIONS 2 ALL MODELS The Hydro-Heater mounts easily to the underside of a holding vessel, leaving the entire vessel area free. Units are shipped ready to inst all with all gaskets and fittings. Hydro-Heaters include a stainless steel front, powder coated body , a low- water cut-off system and a convenient drain outlet.
SPECIFICA TIONS 3 Form No. FR2M-0604 Kilowatt s Wire Sizing Fuse or Model V olt age (kW) Phase Amp s A WG* † Circuit Breaker* Shipping Weight FR2-3 208 3 1 14.5 12 20 24 lbs. (1 1 kg) FR2-4 208 4 1 19.2 12 30 24 lbs. (1 1 kg) FR2-6 208 6 1 28.8 10 40 27 lbs.
SPECIFICA TIONS 4 Form No. FR2M-0604 DIMENSIONS A C B ELECTRICAL Install a fused disconnect switch or circuit breaker sized according to the applicable Electrical Rating Chart . The wiring from the switch or circuit breaker to the Hatco unit must be in accordance with local electrical requirements and codes.
INST ALLA TION 5 Form No. FR2M-0604 PLUMBING An adhesive backed paper template is shipped with the unit and is used to locate the sink strainer holes. Use the following procedure to install the heater unit to the holding vessel.
INST ALLA TION 6 Form No. FR2M-0604 CAUTION W ater Quality Requirement s - Incoming water in excess of 3.0 grains of hardness per gallon (GPG) (.75 grains of hardness per liter) must be treated or sof tened before being supplied to a Hydro-Heater . W ater cont aining over 3.
OPERA TION 7 W ARNINGS Hatco FR2 series unit s are designed for commercial use only by properly trained personnel! W ARNINGS Unit s are designed to heat water up to 190ºF (88ºC). T o avoid any injury or damage DO NOT set temperature controls to a setting higher than 190ºF (88ºC).
OPERA TION 8 Form No. FR2M-0604 W ater T emp. At St art-Up T emperature °F (°C) Water Heated T o: W ater T emp. At St art-Up T emperature °F (°C) Water Heated T o: MINUTES TO HEA T T ABLE 9" .
MAINTENANCE 9 GENERAL W ARNING T o avoid any injury , turn the power switch off at the fuse disconnect switch/circuit breaker or unplug the unit from the power source and allow to cool completely before performing any maintenance or cleaning. Recommended Cleaning Schedule Complete draining and cleaning should be done • On a daily basis.
MAINTENANCE 10 Form No. FR2M-0604 WEEKL Y (See Figure 8) 1. T urn power switch to the OFF position. 2. Drain holding vessel to discharge visible water and debris. 3. Wipe visible deposits from the sink or t ank. 4. Remove clean-out caps (2- or 3-element unit s only).
MAINTENANCE 11 Form No. FR2M-0604 6. After cleaning, drain all expended solution from the unit through the sump drain. 7. Thoroughly wash heater tank with fresh water for several minutes until discharge is clear and all deliming solution has been removed and rinsed.
12 Form No. FR2M-0604 HA TCO LIMITED W ARRANTY 1. PRODUCT W ARRANTY Hatco warrants the product s that it manufactures (the “Products”) to be free from defect s in materials and workmanship, under .
13 Form No. FR2M-0604 NOTES.
HA TCO CORPORA TION P .O. Box 340500, Milwaukee, WI 53234-0500 U.S.A. (800) 558-0607 (414) 671-6350 Parts & Service Fax (800) 690-2966 Int’l. Fax (414) 671-3976 www .hatcocorp.com HA TCO AUTHORIZED P ARTS DISTRIBUTORS Printed in U.S.A. June 2004 ALABAMA Jones McLeod Appl.
An important point after buying a device Hatco FR2 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hatco FR2 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hatco FR2 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hatco FR2 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Hatco FR2 Series will certainly help you make a decision on the purchase.
If you already are a holder of Hatco FR2 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hatco FR2 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Hatco FR2 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hatco FR2 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
