Instruction/ maintenance manual of the product PUB 0804 Hasbro
Go to page of 18
1 Illuminator Glider Door Installation Manual Ultimate Products Inc. • 2319 Laurelbrook Street• Raleigh, NC 27604 • (800) 542 - 7221 • Fax (919) 834 - 4526 PUB 0804.
2 Tools required for Installation Items needed but not included: Screws for mounting track assembly. Impact Wrench Electric or cordless drill Set of drill bits 1/4” to 9/16” Set of box - end wrenc.
3 Parts Identification GLP2003 - Glider Pulley with Bolt and Nut CV100: Cam Valve QD100: Quick Exhaust Valve AP1078: Male Tube Stem AP1075: 3/8" x 1/4" Reducing elbow quick connect AP1080: 3.
4 Parts Identification Continued E - 1 E - 2 A - 1 A - 2 B - 2 B - 1 C - 2 C - 1 D - 2 D - 1 C - 1: Left Hand Slotted Glider Stop C - 2: Right Hand Slotted Glider Stop B - 1: Left Hand Glider Stop B -.
5 Insure that Walls on each side of door opening are clear of all obstructions (Door will protrude 5 1/2” Into building) Install bottom of door track 1” above door opening Door Opening 1” A 1 2 .
6 Panel #1 Panel #2 Panel #3 Panel #4 Panel Identification: Install all panels w/ center Brace on inside of building.
7 Slide Panel #1 & 2 (see page 4) Into track #1 As shown in figure C and step number 6 below. Make sure center brace is on the inside of building 5 C Slide Panel #4 (Clear Section) Into track #2 A.
8 9 Slide panels #2 and #3 to the right hand side of track - The track that does not have the operator Place all panels as shown on page 4 so the door is in the closed position 10 Preparing to install.
9 11 Install Blocks on Door Sections Panel #2 Panel #4 B - 1 C - 1 D - 1 Install Items ‘B - 1,C - 1, and ‘D - 1’ on Panel #2 and Panel #4 as shown Install Items ‘B - 2’, ‘C - 2’ and ‘D.
10 12 Install Items ‘A - 1’and‘A - 2’ Panel #2 Panel #4 A - 1 With Door Sections in Closed position: Install item ‘A - 1’ on Panel #2. The guide bar is inserted into slot of A - 1 as shown.
11 13 Install Items ‘E - 1’and ‘E - 2’ Keeping Door in Closed Position: Insert item ‘E - 1’ onto guide bar of panel #2 and attach to wall with screws.
12 16 Install Bracket ‘A’ Slide Bracket ‘A’ onto operator rod and position bracket ‘A’ 3” from edge of door as shown on step #17. Now attach aluminum block to operator rod as shown 17 A B A 3” 3” *Important: Push Operator Rod fully into cylinder.
13 Air Powered Operator Track 33” minimum 33” minimum 8 1/4” Door Opening Door Opening 20 Run cable around top of pulley on right side of track and through top slot of aluminum block on bracket ‘B’ (do not tighten block until later) 19 Run cable through top slot of bracket ‘A’: A Tighten bolts of aluminum block down onto cable.
14 22 Install brush on bottom of door sections Install brush on bottom of each panel so that brush angles in- ward as shown. (Brushes will angle toward each other) Bottom of brush should touch floor for a proper seal.
15 23 Install floor guides J K Space Items ‘J’ & ‘K’ 2 1/4” apart Make sure center of floor guides are in center of door opening Place item ‘J’ even w/ door opening 24 Install Air Fi.
16 Left side of operator (inside looking at door) Right side of operator (inside looking at door) A A B C D H G F E J I B D Connect Air line from “A” (left side of operator) to “F” Connect Air.
17.
18 Door opening requirements for Glider Door For 10’ opening — Minimum of 33” of side room on each side Operator will open the door 9’9” wide leaving 1 1/2” of door in opening Make Floor level! Track and operator weight approx. 155 pounds.
An important point after buying a device Hasbro PUB 0804 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hasbro PUB 0804 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hasbro PUB 0804 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hasbro PUB 0804 you will learn all the available features of the product, as well as information on its operation. The information that you get Hasbro PUB 0804 will certainly help you make a decision on the purchase.
If you already are a holder of Hasbro PUB 0804, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hasbro PUB 0804.
However, one of the most important roles played by the user manual is to help in solving problems with Hasbro PUB 0804. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hasbro PUB 0804 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
