Instruction/ maintenance manual of the product 93762 Harbor Freight Tools
Go to page of 29
HORIZONT AL/VERTICAL MET AL CUTTING BANDSA W Model 93762 SET UP AND OPERA TING INSTRUCTIONS Visit our website at: http://www .harborfreight.com Read this material before using this product. Failure to do so can result in serious injury . SA VE THIS MANUAL.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 2 CONTENTS IMPORT ANT SAFETY INFORMA TION ........................... 3 GENERAL T OOL SAFETY W ARNINGS ..................................... 3 BAND SA W SAFETY W ARNINGS .... 5 VIBRA TION SAFETY .
SKU 93762 For technical questions, please call 1-800-444-3353. Page 3 SA VE THIS MANUAL Keep this manual for the safety warn- ings and precautions, assembly , operat- ing, inspection, maintenance and cleaning procedures.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 4 DON’T FORCE TOOL. It will do the 7. job better and safer at the rate for which it was designed. USE RIGHT TOOL. Don’t force tool 8. or attachment to do a job for which it was not designed.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 5 or other part that is damaged should be properly repaired or replaced. DIRECTION OF FEED. Feed work 20. into a blade or cutter against the direction of rotation of the blade or cutter only .
SKU 93762 For technical questions, please call 1-800-444-3353. Page 6 Keep all safety guards in place and in 19. proper working order . Use indoors only . 20. If the teeth of the Saw Blade are so 21. far apart that they straddle the work- piece, severe damage to the work- piece and/or Saw Blade will result.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 7 ditions and situations that may occur . It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator .
SKU 93762 For technical questions, please call 1-800-444-3353. Page 8 Improper connection of the equip- 3. ment-grounding conductor can re- sult in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equip- ment-grounding conductor .
SKU 93762 For technical questions, please call 1-800-444-3353. Page 9 SPECIFICA TIONS Motor 120 V~ / 60 Hz / 1 HP / n 0 1700/min Cutting Capacity 4-1/2” Round Stock / 4” x 6” Rectangular Stock S.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 10 T o Attach The Bandsaw T o The Stand: ST AND (TOP VIEW) MOUNTING HOLE MOUNTING HOLE MOUNTING HOLE MOUNTING HOLE MOUNTING HOLE MOUNTING HOLE SCREW (59) SPRING W ASHER (58) FLA T W ASHER (57) FIGURE B 1.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 1 1 T o Attach The Pulley Cover: PULLEY COVER (72) WORM SHAFT (9) MOTOR SHAFT (81) BODY FRAME (60) HEX BOL T (76) FLA T WASHER (77) FIGURE D Position the Pulley Cover (72) over the Worm Shaft (9) and Motor Shaft (81).
SKU 93762 For technical questions, please call 1-800-444-3353. Page 12 MA TERIAL SPEED (FPM) PULLEY GROOVE SPINDLE MOTOR T ool Steel, Stainless Alloy Steels, Bearing Bronze 80 Large Small Medium to Hi.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 13 SCREW (190) SMALL VERTICAL CUTTING PLA TE (194) FIGURE I SCREW (190) VERTICAL CUTTING PLA TE (189) 2. Remove the two Screws (190), and remove the Small V ertical Cutting Plate (194).
SKU 93762 For technical questions, please call 1-800-444-3353. Page 14 OPERA TING INSTRUCTIONS CAUTION! T urn the Power Switch (164) to its “OFF” position and un- plug the tool from its electrical outlet prior to making adjustments to the tool. T o Use The Vise: Raise the Body Frame (60) to its 1.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 15 Adjustments T o Adjust The Stock Stop: SHAFT (158) SOCKET HEAD SCREW (156) STOCK STOP (157) WORKPIECE (NOT INCLUDED) FIGURE M 1. Loosen the Socket Head Screw (156) that holds the Stock Stop (157) to the Shaft (158).
SKU 93762 For technical questions, please call 1-800-444-3353. Page 16 ing the Locking Pin (153). (See Figure H.) T urn on the Bandsaw . The Saw 2. Blade (82) is tracking properly when the back of the Blade is just touch- ing the edge of the Blade Wheel (37) ange.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 17 When the Bandsaw is not in use over 2. long periods of time, release the ten- sion on the Saw Blade (82).
SKU 93762 For technical questions, please call 1-800-444-3353. Page 18 Basic Bandsaw Operation -- V ertical Position: 1. W ARNING! Always wear ANSI- approved safety impact eye goggles when operating the Bandsaw .
SKU 93762 For technical questions, please call 1-800-444-3353. Page 19 from its electrical outlet. (See Figure S.) W ait until the Saw Blade (82) comes 15. to a complete stop. Then, remove the workpiece and scrap material from the V ertical Cutting Plate (189).
SKU 93762 For technical questions, please call 1-800-444-3353. Page 20 Blade into the workpiece. (See Fig- ure T .) 10. W ARNING! Keep hands and ngers safely away from the cut - ting area. Slowly lower the Body Frame (60), 1 1. while it gradually feeds the Saw Blade (82) into the workpiece.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 21 INSPECTION, MAINTENANCE, AND CLEANING 1. W ARNING! Make sure the Power Switch (164) is in its “OFF” position and the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 22 Place the new Saw Blade (82) be- e. tween each of the Guide assemblies and around the Upper Blade Wheel (37) and Lower Blade Wheel (54). IMPORT ANT : The teeth must be pointing downward toward the Motor .
SKU 93762 For technical questions, please call 1-800-444-3353. Page 23 T o lubricate the Worm Gear and 5. Worm Shaft: The W orm Gear (17) and Gear Shaft (19) run in an oil bath Gear Box and should not.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 24 TROUBLESHOOTING.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 25 P ARTS LIST Part # Description Qty 1 Spindle Pulley 1 2 Socket Head Screw(M8x8) 1 3 Screw(M4x8) 1 4 Flat W asher(4) 1 5 Flat W as.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 26 P ARTS LIST (CONT .) Part # Description Qty 80 Motor Pulley 1 81 Key(C5x28) 1 82 Motor 1 83 Blade 1 84 Blade Guide Bracket Seat 1.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 27 Part # Description Qty 163 Shaft 1 164 Cable Protector 1 165 Switch Panel 1 165-1 Switch Box 1 166 Screw(M3.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 28 ASSEMBL Y DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. 194: V ertical Cutting Plate Support Not Shown.
SKU 93762 For technical questions, please call 1-800-444-3353. Page 29 LIMITED 1 YEAR / 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and.
An important point after buying a device Harbor Freight Tools 93762 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harbor Freight Tools 93762 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harbor Freight Tools 93762 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harbor Freight Tools 93762 you will learn all the available features of the product, as well as information on its operation. The information that you get Harbor Freight Tools 93762 will certainly help you make a decision on the purchase.
If you already are a holder of Harbor Freight Tools 93762, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harbor Freight Tools 93762.
However, one of the most important roles played by the user manual is to help in solving problems with Harbor Freight Tools 93762. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harbor Freight Tools 93762 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
