Instruction/ maintenance manual of the product 90003 Harbor Freight Tools
Go to page of 16
6” BENCH GRINDER Model 90003 ASSEMBL Y AND OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our W eb site at: http://www .
PRODUCT SPECIFICA TIONS SA VE THIS MANUAL Y ou will need this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures, parts list and as- sembly diagram. Keep your invoice with this manual.
3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. ELECTRICAL SAFETY 4.
11 . Dress properly . Do not wear loose clothing or jewelry . Contain long hair . Keep your hair , clothing, and gloves away from moving parts. Loose clothes, jewelry , or long hair can be caught in moving parts. 12. A void accidental starting. Be sure the Power Switch is off before plugging in.
22. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’ s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly main- tained tools. 23. Use only accessories that are recommended by the manufacturer for your model.
15. Check for damaged parts. Before using this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may af fect the safe operation of this product. Replace or repair damaged or worn parts immediately .
22. Always turn off the Bench Grinder and unplug it from its electrical outlet before changing accessories or performing any inspection, mainte- nance, or cleaning procedures. 23. W ARNING! The warnings and cautions discussed in this manual cannot cover all possible conditions and situations that may occur .
FIGURE A SKU 90003 P AGE 8 2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’ s grounding system and must never be attached to an electrically “live” terminal.
SKU 90003 P AGE 9 EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord.
SKU 90003 P AGE 10 SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V olts Alternating Current Amperes No Load Revolutions per Minute (RPM) n o xxxx/min. A V ~ UNP ACKING When unpacking, check to make sure all the parts shown on the Parts List on page 15 are included.
SKU 90003 P AGE 1 1 3. Repeat Steps #1 and #2 to attach the Right T ool Rest (part #32) to the Right Wheel Guard (part #31). (See Figure D.) LEFT WHEEL GUARD (#27) RIGHT WHEEL GUARD (#31) RIGHT TOOL REST (#32) LEFT TOOL REST (#28) SCREW WITH LOCK W ASHER (#25) FIGURE D T o Attach The Spark Guards: 1.
SKU 90003 P AGE 12 T o Attach The Eye Shield Mounting Rods: 1. Insert one Screw (part #48) with a W asher (part #13) through a Bracket (part #36) and the Left Eye Shield Mounting Rod (part #49). Then, firmly tighten the Screw to secure the Left Eye Shield Mounting Rod to the body of the Bench Grinder .
SKU 90003 P AGE 13 LEFT EYE SHIELD MOUNTING ROD (#49) RIGHT EYE SHIELD MOUNTING ROD (#33) SCREW (#55) SCREW (#55) PRESSURE PLA TE (#50) PRESSURE PLA TE (#50) FIGURE G 2. There are two 1 1/32” diameter mounting holes located on the Base (part #15) of the Bench Grinder .
SKU 90003 P AGE 14 OPERA TING INSTRUCTIONS 2. Plug the Power Cord Plug (part #10) into the nearest grounded, 120 volt, electri- cal outlet. Then, turn the Power Switch (part #3) to its “ON” position and allow the Grinding Wheels (part #64) to spin up to full speed.
SKU 90003 P AGE 15 P ARTS LIST NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts.
NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 90003 P AGE 16 ASSEMBL Y DIAGRAM 26 58 57 58 52 53 54 50 51 55 48 36.
An important point after buying a device Harbor Freight Tools 90003 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harbor Freight Tools 90003 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harbor Freight Tools 90003 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harbor Freight Tools 90003 you will learn all the available features of the product, as well as information on its operation. The information that you get Harbor Freight Tools 90003 will certainly help you make a decision on the purchase.
If you already are a holder of Harbor Freight Tools 90003, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harbor Freight Tools 90003.
However, one of the most important roles played by the user manual is to help in solving problems with Harbor Freight Tools 90003. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harbor Freight Tools 90003 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
