Instruction/ maintenance manual of the product 65076 Harbor Freight Tools
Go to page of 18
24 T ON LOG SPLITTER 65076 SET UP , OPERA TING, AND SER VICING INSTRUCTIONS W ARNING! IMPORT ANT INFORMA TION The Hitch Coupler MUST be properly secured to the hitch ball of the towing vehicle. After assembly and attachment, pull up and down on the Hitch Coupler to make sure the hitch ball is tting snugly in the Hitch Coupler .
SKU 65076 For technical questions, please call 1-800-444-3353. Page 2 CONTENTS IMPORT ANT SAFETY INFORMA TION ............................ 3 BASIC SPECIFICA TIONS ............. 7 UNP ACKING .................................. 7 SET UP INSTRUCTIONS ....
SKU 65076 For technical questions, please call 1-800-444-3353. Page 3 SA VE THIS MANUAL Keep this manual for the safety warn- ings and precautions, assembly , operat- ing, inspection, maintenance and cleaning procedures.
SKU 65076 For technical questions, please call 1-800-444-3353. Page 4 Wear ANSI-approved safety goggles, 5. heavy-duty work gloves, and dust mask/respirator during set up. Use only lubricants and fuel recom- 6. mended in the engine manual or in the Specications chart of this man - ual.
SKU 65076 For technical questions, please call 1-800-444-3353. Page 5 Never split a log that contains any 10. foreign materials (nails, for example). Never place your hands or body near 1 1. a hydraulic uid leak. High-pressure uid can be forced under the skin resulting in serious injury .
SKU 65076 For technical questions, please call 1-800-444-3353. Page 6 SER VICE PRECAUTIONS Before service, maintenance, or 1. cleaning: T urn the engine switch to its a. “OFF” position. Allow the engine to completely b. cool. Then, remove the spark plug c.
SKU 65076 For technical questions, please call 1-800-444-3353. Page 7 BASIC SPECIFICA TIONS Fuel T ype 89+ octane unleaded gasoline Capacity 1 Gallon Equipment Lubricant T ype 5W30 (above 32° F) 10W30 (at 32° F or below) Capacity 1.1 Quarts Hydraulic Fluid 2.
SKU 65076 For technical questions, please call 1-800-444-3353. Page 8 cleaned even if they are new or ap- pear clean. Allow all pieces to dry completely . 4. Place fresh, clean bearing grease in 5. the packer . With the grease-lled bearing packer 6.
SKU 65076 For technical questions, please call 1-800-444-3353. Page 9 FIGURE 2 FIGURE 3 Push Pin (26) Oil Plug (37) with air inlet ho le Close-up of Push Pin (26) securing the Front Leg Assembly (1 1) to the bracket on the Oil T ank Assembly (10B). Second Push Pin (26) secures Rail Assembly (2), and is removed for vertical log splitting.
SKU 65076 For technical questions, please call 1-800-444-3353. Page 10 Rail Assembly must always be se - cured in the horizontal position for travel. Cover the air inlet hole on the Oil Plug (37) before transport. See FIGURE 3. Pull up and down on the Hitch Cou- 15.
SKU 65076 For technical questions, please call 1-800-444-3353. Page 1 1 Hair Pin Clip into the vertical position hole (See FIGURE 1). Reverse the process to return to the horizontal position. Remove the Oil Plug (37) and ll the 4. tank with Hydraulic oil (not included).
SKU 65076 For technical questions, please call 1-800-444-3353. Page 12 SER VICING TO PREVENT SERIOUS INJUR Y FROM ACCIDENT AL ST ARTING: T urn the Power Switch of the equipment to its “OFF” position, wait for the engine to cool, and disconnect the spark plug wire(s) before performing any inspection, maintenance, or cleaning procedures.
SKU 65076 For technical questions, please call 1-800-444-3353. Page 13 sembly is reassembled, tighten the Castle Nut until the wheel starts spin- ning with slight resistance. Loosen the Castle Nut about 1/2 turn from this point. Insert a new Cotter Pin through the Castle Nut and the hole in the axle.
SKU 65076 For technical questions, please call 1-800-444-3353. Page 14 Part Description Qty . 1 Cylinder 1 2 Rail Assembly 1 3 Slide Assembly 1 4 Safety Chain With Hook 1 5 Slide Guide 2 6 Slide Retai.
SKU 65076 For technical questions, please call 1-800-444-3353. Page 15 ASSEMBL Y DIAGRAM 08 2.
SKU 65076 For technical questions, please call 1-800-444-3353. Page 16 HYDRAULIC RAM SEALS W arning! Only a qualied technician should repair or service the internal hydraulic system of this unit.
SKU 65076 For technical questions, please call 1-800-444-3353. Page 17 HYDRAULICS DRA WING.
SKU 65076 For technical questions, please call 1-800-444-3353. Page 18 LIMITED 1 YEAR / 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every ef fort to assure that its products meet high quality an.
An important point after buying a device Harbor Freight Tools 65076 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harbor Freight Tools 65076 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harbor Freight Tools 65076 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harbor Freight Tools 65076 you will learn all the available features of the product, as well as information on its operation. The information that you get Harbor Freight Tools 65076 will certainly help you make a decision on the purchase.
If you already are a holder of Harbor Freight Tools 65076, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harbor Freight Tools 65076.
However, one of the most important roles played by the user manual is to help in solving problems with Harbor Freight Tools 65076. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harbor Freight Tools 65076 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
