Instruction/ maintenance manual of the product 34202 Harbor Freight Tools
Go to page of 14
40 LB. PRESSURIZED SANDBL ASTER ASSEMBL Y and OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd. / Camarillo, CA 9301 1 Copyright © 1997 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight T ools.
SPECIFICA TIONS Capacity: 40 lbs. Working Pressure 60-125 PSI Delivery Rate 6-25 CFM Overall Dimensions 33.5" x 18.75" x 13" Weight: 57 lbs. SA VE THIS MANUAL Y ou will need the manual for the safety warnings and cautions, assembly instructions, operating procedures, maintenance procedures, trouble shooting, parts list, and diagram.
9. DO NOT ABUSE THE POWER CORD. Do not yank compressor ’s cord to disconnect it from the receptacle. Do not carry tools by the cord. 10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or across running machines. 11 .
22. MAINT AIN CORRECT AIR PRESSURE WHENEVER WORKING . Do not allow pressure to exceed 125 PSI. If the safety valve does not release excess air pressure, stop all work and use the air compressor to release pressure in the tank. Do not attempt any repairs to the Sandblaster until its gauge reads “0”.
ASSEMBL Y NOTE: Use T eflon® Pipe T ape on all threaded joints. Make sure all joints are securely tighten. Intake Manifold Refer to Figure 1. S tep1: Get out the INT AKE MANIFOLD (#14), PRESSURE GAUGE (#15), BRASS THROTTLING V AL VE (#18A), 3/8" 1/4" NIPPLE CONNECTOR (#20), and JOINT PIPE (#13).
Water Trap Refer to Figure 2. Figure 2 — Water Trap Assembly S tep1: Get out the WA TER TRAP (#17), two 3/8" NIPPLE CONNECTORS (#16), the BRASS AIR SUPPL Y V AL VE (#18), and the MALE/FEMALE ADAPTER (#19). S tep2: A tt ach the 3/8" NIPPLE CONNECTORS to either side of the W A TER TRAP .
Nozzle Shut Off V alve Refer to Figure 4. S tep1: Get out the HOSE ADAPTER (#25), the STEEL SHUT OFF V AL VE (#18C), a NIPPLE CONNECTOR (#16), the GASKET (#26), the desired size NOZZLE (#27A-D), and the NOZZLE CAP NUT (#28). S tep2: Put the front of the NOZZLE through the NOZZLE CAP NUT .
S tep5: At t ach the HOSE ADAPTER to the other end of the STEEL SHUT OFF V AL VE. Sand Control V alve/ Nozzle Shut Off V alve Refer to Figure 5. Sand Con trol V alve Assem bly Sand Hose Nozzle Shut O .
T op Assembly Refer to Figure 6. T ank (# 1) Ni pple Connector (# 16) Ni pple Connector (# 16) Air Hos e (# 21) Gasket (# 1 1) Air Ca p (# 12) Joint P ipe (# 13) Figure 6 — T op Assembly S tep1: Get the Int ake V alve Assembly , the W ater Trap Assembly , the T ank Assembly , the T ANK CAP (#12), the O-RING (#1 1), and the AIR HOSE (#21).
Handle Bars Refer to Figure 7. Handl e Grip (# 7) Handl e B ar (# 6) Scre w (# 8) W asher (# 31) Nut (# 9) Figure 7 — Handle Bar Assembly S tep1: Get out the two HANDLE BARS (#6), the two HANDLE GRIPS (#5), the four SCREWS (#8), four NUTS (#9), and four W ASHERS (#31).
Wheels and Foot See Figure 8. 5 3 2 4 3 3 2 Figure 8 - Wheel and Foot Attachment S tep 1: Get out the two WHEELS (#2), the three COTTER PINS (#3), the FOOT (#4) and the AXLE (#5). S tep 2: Attach the FOOT to the T ANK (#1) using one of the COTTER PINS.
OPERA TIONS Loading Abrasives S tep 1: Check to insure the abrasives are dry and clean so that they do not clog the unit. S tep 2: Close the AIR SUPPL Y V AL VE (#18) by turning it to the horizontal position. S tep 3: Open the NOZZLE SHUT OFF V AL VE (#18C) by turning it to the vertical position.
Item# Description Q ty Item# Description Q ty 1 T a nk 1 18B 3/8" S teel Sand Control V alve 1 2 Wheel 2 18C 3/8" S teel Shut Off V alve 1 3 Cotter Pin 3 1 9 Male/Female Adapter 1 4 Foot 1 2.
19 16 16 17 15 14 18A 20 18 13 7 8 9 3 5 21 14 2 1 24 23 28 27A-D 26 16 18C 25 16 18B 16 22 23 31 12 11 10 6 3 P ARTS DRA WING Page #14 -- SKU 34202.
An important point after buying a device Harbor Freight Tools 34202 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harbor Freight Tools 34202 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harbor Freight Tools 34202 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harbor Freight Tools 34202 you will learn all the available features of the product, as well as information on its operation. The information that you get Harbor Freight Tools 34202 will certainly help you make a decision on the purchase.
If you already are a holder of Harbor Freight Tools 34202, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harbor Freight Tools 34202.
However, one of the most important roles played by the user manual is to help in solving problems with Harbor Freight Tools 34202. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harbor Freight Tools 34202 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
