Instruction/ maintenance manual of the product 31849 Harbor Freight Tools
Go to page of 17
31849 ASSEMBL Y & OPERA TING INSTR UCTIONS 7” RABBETING JOINTER WITH ST AND 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb Site at www .
THANK Y OU for choosing a HARBOR FREIGHT T OOLS product. F or future ref erence , please complete the owner’ s record below: Model ______________ Serial No. ______________ Purchase Date _____________ SA VE THE RECEIPT , W ARRANTY AND THESE INSTR UCTIONS.
W ork Area T O A V OID RISK OF PERSONAL INJUR Y , EQUIPMENT D AMAGE, FIRE AND SHOCK, MAKE SURE Y OUR WORK AREA IS: F ree of damp , wet or rainy conditions . F ree of children (ne ver let them handle tools or machinery). W ell-lit. Clean and uncluttered.
Grounding/V oltage W arning Common household current is 110-120 volts . As long as the outlet used with the tool is rated from 110-120V there will be no complications using it with household receptacles. Plug the tool into a 110-120V properly grounded outlet protected b y a 15-amp , dual element time dela y or circuit break er .
The Stand Step 1) Attach the F ront Side Plate (#16A) to both of the Side Link Plates (par t #19A). Inser t two Screws (#17A) through F ront Side Plate and through Side Link Plate. Slide on W ashers (#7A) and Nut (#6A). Tighten into place . Repeat for the other side - see Figure 1.
Step 9) Attach the T apping Plate (#25A) with Right and Left T apping F enders (#23A & #27A) to the Left Protecting Plate (#26A). Insert the Screws (#17A) with head on the outside of the Plate. On the inside, slide on Washer (#7A) and Nut (#6A)-see Figure 2.
Cutterhead Guard W arning: Be ware of sharp blade when installing the Cutterhead Guard. Step 1) Inside of the Spring Knob (#37) there is a Spring (#36) which returns the Guard toits position abov e the Cutterhead after a cut. T o create tension in the Spr ing, tur n the Spring Knob (#37) bef ore inser ting the post.
Step 2) Flip the square jib so that its end sits against the flat par t of the Plate (18)-see Figure 7. Step 3) Using an Allen Wrench, attach this assemb ly to the F ence (#11) with the three Hex Scre ws (#24)-see Figure 6.
Fence Adjustments The F ence (par t #11) is assembled to the front of the Inf eed T ab le (#33). The F ence can be moved across the T ab le and can be tilted 45 degrees right or left by using the Handle P ole (#29). Step 1) T o move the F ence (#11) across the T able , turn the Handle Pole (#29) to loosen.
Step 4) If the knife is not aligned at one or both sides, loosen Bolts (60) which hold the Knife Lock Bar (61). Use a knife setting gauge (not included) to make sure that the knife at each end of the cutter is the same height. Repeat for the next two (2) knives as is fitting.
Step 8) Secure the rear table in position and remove the feeler gauge. Step 9) Lower the infeed table and place a straight edge on the outfeed table so that it e xtends out o ver the cutterhead. Step 10) T urn the cutterhead by hand until the knif e is at its highest point at each end of the cutterhead.
T ur ning the Jointer ON and OFF Step 1) T o tur n the Jointer ON, press down on the green b utton on top . Step 2) T o tur n OFF the Jointer, press do wn the red b utton on the bottom. IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE , DO NOT OPERA TE THE T OOL .
Unpac king UNP A CK AND CHECK CONTENTS When unpacking y our Jointer with Stand chec k to mak e sure the f ollo wing parts are included. If an y parts are missing or broken, please call HARBOR FREIGHT T OOLS at 1-800-444-3353.
P ar ts List - Jointer Assemb ly P ar t # Description Quantity Par t # Description Quantity 1 Outf eed T ab le 1 36 Spring 1 2 Bearing Housing 1 37 Spring Knob 1 3 Ball bearing 1 38 Retainer 1 4 Cutte.
Stand Assemb l y Dia gram Each of the P ar t Numbers below correspond to the Stand Assemb ly and has the suffix “A” - see P ar ts List on P age 13.
Jointer Assembly Diagram - See Parts List on Page 14 #31849 Page 16.
White White Black Black Wiring Dia gram #31849 Page 17.
An important point after buying a device Harbor Freight Tools 31849 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harbor Freight Tools 31849 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harbor Freight Tools 31849 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harbor Freight Tools 31849 you will learn all the available features of the product, as well as information on its operation. The information that you get Harbor Freight Tools 31849 will certainly help you make a decision on the purchase.
If you already are a holder of Harbor Freight Tools 31849, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harbor Freight Tools 31849.
However, one of the most important roles played by the user manual is to help in solving problems with Harbor Freight Tools 31849. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harbor Freight Tools 31849 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
