Instruction/ maintenance manual of the product Axor 35115801 Hans Grohe
Go to page of 16
Steel 35115801 Steel 35116801 Installation Instructions / W arranty.
2 W all Mounted Single-Handle Lav Set with Base Plate 35115801 W all Mounted Single-Handle Lav Set 35116801 35115801 35116801 T echnical Information Max. flow rate: 1.5 gpm Max. water pressure: 147 psi Recommended pressure: 14.7 - 72 psi T est pressure: 232 psi Max.
3 Seal the wall around the plaster shields with waterproof sealant. Failure to seal the wall can lead to possible water damage. Installation Remove the covers from the plaster shields (1). T rim the plaster shields so that they extend 1/16” outside the surface of the finished wall (2).
4 Install the cup washers and springs in the rough. Install the cartridge assembly . Push the handle over the cartridge stem. T ighten the handle screw with a 2 mm Allen wrench. If you are installing 35115801, turn to page 5. If you are installing 35116801, turn to page 9.
5 Model 35115801 only: Measure the distance between the wall surface and the end of the handle (x). If x is between 3 1/4” and 3 5/8”, select the two “A” sleeves (1 1/4”). If x is between 3 4/8” - 4”, select the two “B” sleeves (7/8”).
6 Connect the fixation nuts to the sleeves. Measure the distance from the rough to the outside surface of the finished wall (X) (1). Add 1 3/4” to X. Cut the spout connecting thread so that it is X + 1 3/4” long (2). W rap the connecting thread with T eflon tape.
7 T ighten the retaining nuts using the ser vice key . Lightly lubricate the o-rings on the spout and handle escutcheons with the enclosed lubricant (1). Push the escutcheons onto the baseplate (2). Push the baseplate against the wall (1). Thread the sleeves into the rough (2).
8 Push the spout over the connecting thread (1). T ighten the set screw with a 3 mm Allen wrench (2). Install the handle flange (3). 1. 2. 3..
9 Model 35116801 only: Measure the distance between the wall surface and the end of the handle (x). If x is between 3 1/4” and 3 5/8”, select the “A” sleeve (1 1/4”). If x is between 3 5/8” - 4”, select the “B” sleeve (7/8”). If x is greater than 4”, select the “C” sleeve (1/2”).
10 Push the sleeve / handle escutcheon assembly into place over the handle (1). T ighten it by rotating it clockwise (2). Push the flange over the handle. Push the sealing ring into the handle escutcheon (1). Install the handle escutcheon onto the sleeve (2).
11 Measure the distance from the rough to the out- side surface of the finished wall (X) (1). Add 1 3/4” to X. Cut the spout connecting thread so that it is X + 1 3/4” long (2). W rap the spout connecting thread with T eflon tape. Install the spout connecting thread.
12 35115801 User Instructions Pivot the handle up to turn the water on, down to turn it off. Pivot the handle to the left for warmer water , to the right for cooler water .
13 35116801 1 flange 96908800 2 handle 35094800 3 handle escutcheon 96912800 4 spout escutcheon 96913800 5 baseplate 96927800 6 cartridge 96339000 7 aerator 95386800 8 spout 97282800 9 anti-twist devi.
14 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada.
15 including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year , with respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products. THIS W ARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT P A Y FOR: A.
16 US - Installation Instructions • Part No. 90505803 • Revised 12/2008 Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el.
An important point after buying a device Hans Grohe Axor 35115801 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hans Grohe Axor 35115801 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hans Grohe Axor 35115801 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hans Grohe Axor 35115801 you will learn all the available features of the product, as well as information on its operation. The information that you get Hans Grohe Axor 35115801 will certainly help you make a decision on the purchase.
If you already are a holder of Hans Grohe Axor 35115801, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hans Grohe Axor 35115801.
However, one of the most important roles played by the user manual is to help in solving problems with Hans Grohe Axor 35115801. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hans Grohe Axor 35115801 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
