Instruction/ maintenance manual of the product 35116801 Hans Grohe
Go to page of 16
Installation Instructions / W arranty Steel 35115801 Steel 35116801.
2 W all Mounted Single-Handle Lav Set with Base Plate 35115801 W all Mounted Single-Handle Lav Set 35116801 35115801 35116801 T echnical Data Max. flow rate: 2 .2 g p m Max. water pressure: 147 psi Recommended pressure: 14.7 - 72 psi T est pressure: 232 psi Max.
3 Installation with 38111181 rough manufactured before 03/2004 T urn the water off at the supply before beginning this installation. Remove the covers from the plaster shields (1). T rim the plaster shields so that they extend 1/16” out- side the surface of the finished wall (2).
4 Install the new cup washers and springs in the rough. Install the cartridge assembly . Installation with 38111181 rough manufactured after 04/2004 Remove the covers from the plaster shields. T rim the plaster shields so that they extend 1/16” outside the surface of the finished wall.
5 Install the cartridge and anti-twist device in the housing. Install the cup washers and springs in the rough. Install the cartridge assembly . Installation with all models: Push the handle over the cartridge stem. Tighten the handle screw with a 2 mm Allen wrench.
6 Model 35115801 only: Measure the distance between the wall surface and the end of the handle (x). If x is between 3 1/4” and 3 7/8”, select the two “A” sleeves (1 1/4”). If x is between 3 7/8” - 4 3/8”, select the two “B” sleeves (7/8”).
7 Connect the fixation nuts to the sleeves. Measure the distance from the rough to the outside surface of the finished wall (X) (1). Add 1 3/16” to X. Cut the spout connecting thread so that it is X + 1 3/16” long (2). W rap the connecting thread with T eflon tape.
8 T ighten the retaining nuts with the ser vice key . Lightly lubricate the o-rings on the spout and handle escutcheons with the enclosed lubricant (1). Push the escutcheons onto the baseplate (2). Push the baseplate against the wall (1). Thread the sleeves into the rough (2).
9 Push the spout over the connecting thread (1). T ighten the set screw with a 3 mm Allen wrench (2). Install the handle flange (3). 1. 2. 3..
10 Model 35116801 only: Measure the distance between the wall surface and the end of the handle (x). If x is between 3 1/4” and 3 7/8”, select the “A” sleeve (1 1/4”). If x is between 3 7/8” - 4 3/8”, select the “B” sleeve (7/8”). If x is greater than 4 3/8”, select the “C” sleeve (1/2”).
11 Push the sleeve / handle escutcheon assembly into place over the handle (1). T ighten it by rotating it clockwise (2). Push the flange over the handle. Push the sealing ring into the handle escutcheon (1). Install the handle escutcheon onto the sleeve (2).
12 Measure the distance from the rough to the outside surface of the finished wall (X) (1). Add 1 3/16” to X. Cut the spout connecting thread so that it is X + 1 3/16” long (2). W rap the spout connecting thread with T eflon tape. Install the spout connecting thread.
13 35115801 User Instructions Pivot the handle up to turn the water on, down to turn it off. Pivot the handle to the left for warmer water , to the right for cooler water .
14 Replacement Parts 35116801 1 flange 96908800 2 handle 35094800 3 handle escutcheon 96912800 4 spout escutcheon 96913800 5 baseplate 96927800 6 cartridge 96339000 7 aerator 96683800 8 spout 97282800.
15 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada.
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el. 770 360-9880 • Fax 770 360 9887 www .hansgrohe-USA.com US - Installation Instructions • Part No.
An important point after buying a device Hans Grohe 35116801 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hans Grohe 35116801 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hans Grohe 35116801 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hans Grohe 35116801 you will learn all the available features of the product, as well as information on its operation. The information that you get Hans Grohe 35116801 will certainly help you make a decision on the purchase.
If you already are a holder of Hans Grohe 35116801, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hans Grohe 35116801.
However, one of the most important roles played by the user manual is to help in solving problems with Hans Grohe 35116801. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hans Grohe 35116801 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
