Instruction/ maintenance manual of the product XPB88-LS Haier
Go to page of 40
User's manual XPB88-LS T win-tub W ashing Machine with Pump Names of the parts.............the 2 nd cover Safety precautions ...............................1 Installation and adjustment ..................3 Introduction of the major functions ....
Before Using Before Using Names of the par ts Meaning and description of the symbols Warning sign Forbidding sign Contents marked with that symbol are related to the safety of the product and the personal safety of the users.
Before Using Before Using Safety precautions If the power cord is bad, to avoid risk it is required to replace it by the technicians of our special shop or the after-sale service department. Keep the pin of the power plug clean. Do not put the machine at damp place like the bathroom .
Before Using Before Using Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. T ake special care of the children. Handicapped or children without care shall not use the machine. Do not put any hot or heavy items ( such as the kettle with hot water ) on the washing machine.
Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine.
Extend the drain hose from the rear side How to change the direction of the drain hoses Figure 1 indicates the ex factory installation position of the drain hose. Put soft items on the ground. Lean the machine down gently with the front surface facing the ground.
Quick water-filling entrance If you do not need spraying spin, you can fill water into the wash tub directly through this entrance. It can reduce the humidity inside the control panel significantly and prolong the operating life of the components.
Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3. Put the drain hose up to suitable position.
Reference weight of the laundries Working suit up,down Jeans about 800g The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity.
Selection of the quantity of the washing powder list 1 Selection of the current , water level and washing time list 2 How to use the washing powder How to use the whitener Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub.
Washing sequence Figure 1 Figure 2 Figure 3 Figure 5 SPIN WASH Using process Using process Wash DRAIN DRAIN STRONG WASH SELECTOR WASH SELECTOR 1.Water-filling selector (1) Set the water-filling selector at the "WASH" side. (Figure 1) (2) Set the water level adjusting lever to needed line.
Midway spinning 1. 2. 3. Put the laundries into the spin tub evenly and smoothly. Spin Run the foam-removing spinning. Push Push Proper Proper Outer cover of The spin tub Inner cover of The spin tub The laundries are slanting Gland No gland Using process Using process (1) Put the gland in properly.
Rinse with stored water Rinse with water-filing 1. Put the laundries into the wash tub. Select suitable current according to the laundries. 2. Fill water to preset water level. 3. Rinse Adjust the wash timer to 2-3 minutes to do rinsing. When the laundries quantity is below 2.
Selection of the spin time list 3 Laundries Spin time (minutes) About 4~5 Bed sheet or blanket About 2~4 Underwear (knitwear) Swear (chemical fiber) About 1~2 Within 1 minute Blending thin laundries Using process Using process 1. Put the laundries into the spin tub evenly and smoothly.
After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. 1 Take of f the overflow filter.
Wipe the complete unit with soft cloth twisted dry. Wipe with neutral detergent if too dirty Do not wash it directly by water Using process Using process Cleaning the overflow filter 2. T ake off the corrugation pipe. Dismantle the upper part of the corrugation pipe inside the overflow filter ( as indicated in Figure 1).
Trou ble-shooting Ans wers to question When the remained water is frozen Prevent the freezing (be sure to discharge the water completely after using) After complete draining, set the "WASH SELECTOR" at "STRONG" or "ST ANDARD".
Troub le-shooting Ans wers to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company.
User's manual One One One One One Water inlet hose Water-filling jointer Gland Lint filter Packing list Twin-tub washing machine One.
Type Model Power source Water level Water quantity about Rated input power W Dimension(mm) Wash pattern Weight kg Injection pressure Rated washing capacity kg Twin-tub washing machine with pump XPB88-LS V~, 50Hz Maximum/43L Medium/36L Minimum/30L 8.0 L740 W428 H936 New current 27 0.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
XPB88-LS.
An important point after buying a device Haier XPB88-LS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Haier XPB88-LS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Haier XPB88-LS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Haier XPB88-LS you will learn all the available features of the product, as well as information on its operation. The information that you get Haier XPB88-LS will certainly help you make a decision on the purchase.
If you already are a holder of Haier XPB88-LS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Haier XPB88-LS.
However, one of the most important roles played by the user manual is to help in solving problems with Haier XPB88-LS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Haier XPB88-LS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
