Instruction/ maintenance manual of the product slim3 Haier
Go to page of 26
Front Load W ashing Machine Model:slim3 1 1.Contents------------------- ------------------ --------------------- ---------------- -------------1 2.Features ------------------ ------------------ --------------------- ---------------- -------------3 3.
Front Load W ashing Machine Model:slim3 ３ FRONT LOAD W ASHING MACHINE Service Manual Suited model: Slim3 Features ： ● 300mm diameter porthole, door may be open at a 180 degrees.
Front Load W ashing Machine Model:slim3 ４ FEA TURES ● 300mm diameter porthole, door ma y be open at a 180 degrees. Facilitate view of wash pr ocess, facilit ate unloading and easy to use with large port.
Front Load W ashing Machine Model:slim3 ５ SPECIFICA TION Proposal 2006 New Sensor Front load washing machines Slim3 1. Product identification Description of appliance Washi ng machine T ype of appli.
Front Load W ashing Machine Model:slim3 ６ 5. Programs 1) S trong action /cotton cycles n° 1 2) Normal action / synthetics n° 1 3) Delicate action / w ool cycles n° 1 Pre-wash / wa sh / Qu.
Front Load W ashing Machine Model:slim3 ７.
Front Load W ashing Machine Model:slim3 7.
Front Load W ashing Machine Model:slim3 8.
Front Load W ashing Machine Model:slim3 9.
Front Load W ashing Machine Model:slim3 10.
Front Load W ashing Machine Model:slim3 11 Maintenance.
Front Load W ashing Machine Model:slim3 12.
Front Load W ashing Machine Model:slim3 13 Net dimension 595CM 398CM 850CM.
Front Load W ashing Machine Model:slim3 14 Names of the p art Deterge nt distribution drawer Display door prothole Selection knob Operating buttons Door handle T op pane l.
Front Load W ashing Machine Model:slim3 15.
Front Load W ashing Machine Model:slim3 16.
Front Load W ashing Machine Model:slim3 14 Slim3 Error Display and T roubleshooting Error message:Door is not properly s hut 20s after program is st arted. T roubleshooting: N Pushing the door t o Check Whether Door is proper ly shut or not Shut the door properly Y Error message:Drainage error , wate r not emptied within 4 min.
Front Load W ashing Machine Model:slim3 15 (Fig1) Error message:T emperature sensor is not properly connected or damaged (display at the end of a program).
Front Load W ashing Machine Model:slim3 16 Error message :The heater may be broken T roubleshooting: N Y Y Cut of f power ,check the resistance Of two pins of heater element by multimenter is it betwe.
Front Load W ashing Machine Model:slim3 17 N T urn on power , and set pre-wa sh mode, then start. Check the import voltage of electromagnetic valve by multimeter Y Elec tromagnetic valve must be broken, please replace it. , is it betwee n AC 220-240V?if t he hot water can also co me into disp ensor.
Front Load W ashing Machine Model:slim3 18 Error message. Motor overheat protection or is damaged. T roubleshooting: Error message. W ater level exceeds protection value.
Front Load W ashing Machine Model:slim3 19 N W ithout power ,connect inle t pipe to inlet vavle,then ope n the tap and observe if water is entering in dispen ser Replace inlet va lve Y Replace PCB Y W.
Front Load W ashing Machine Model:slim3 20 Choose pre-w ash program and st art ， Check if there is 220-240V at import pi n of electromagneti c valve （ See fig 2 ） Failure:no draining T roublesho.
Front Load W ashing Machine Model:slim3 21 Adjust adj ustable feet Y N N N N Remove belt and turn belt pulley by hand, and th en check if the re is dif ferent Are the screw s of counterweight and motor loos e? Is belt loose or w or n? Y Is washer i n balance? Replace it Y Y Y Fasten th em Dismantle tria ngle and check the bearing .
Front Load W ashing Machine Model:slim3 22 Wiring circuit.
Front Load W ashing Machine Model:slim3 23 Sincere Forever Gr oup Industrial Park, No.1, Road 266101, Qingdao, China http://www .haier .com.
An important point after buying a device Haier slim3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Haier slim3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Haier slim3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Haier slim3 you will learn all the available features of the product, as well as information on its operation. The information that you get Haier slim3 will certainly help you make a decision on the purchase.
If you already are a holder of Haier slim3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Haier slim3.
However, one of the most important roles played by the user manual is to help in solving problems with Haier slim3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Haier slim3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
