Instruction/ maintenance manual of the product HW701286 Haier
Go to page of 20
Delay Power Heavy Sport wash Quick Spin W ash Rinse Spin T emp. Speed Auto Silk W ool Synthetic Memory Cotton Star t/ Pause Press and hold 2seconds to set door unlocked Delicate Silent S e l f - c l e.
t Able of contents LEGEND For your safety , any instructions in this manual with this "Warning" sign must be followed strictly . Y es No Optional 03 - 09 10 - 15 16- 20 COMPONENTS > ............................... 03 PREP ARATION > ...
03 Before use 1 x I nlet hos e assem bly 1 x D rain ho se bra cket 1 x U ser m an ua l 4x Blan ki ng pl ug s 1 x War ra nt y car d W ARRANT Y CARD (Customer’s Copy) ww w.
04 Before use Delay Power Heavy Sport wash Quick Spin W ash Rinse Spin T emp. Speed Auto Silk W ool Synthetic Memory Cotton Star t/ Pause Press and hold 2seconds to set door unlocked Delicate Silent S.
05 Before use sAfety instructions DO ... ... Make sure that the transport bolt are removed. ... Use a separate earthed socket for the power supply . ... Make sure that the plug is accessible. ... Hold the plug and not the electric cable when unplugging the power supply .
06 Before use 3. 1 . 2. 4. DISMANTLE THE TRANSPOR T A TION BOL TS The transportation bolts are designed for clamping anti-vibration components inside of the washing machine during the transportation process. Remove the back cover . 1. Remove the four bolts on the rear side and take out the synthetic 2.
07 Before use 1 . 2. 1 . 8 0 - 1 0 0cm 2. INLET HOSE 1. Connect the nut on the inlet hose to the connector on the water valve. 2. Apply inlet hose to a water tap with cold, fresh water . Note: Use the hose-set supplied with the appliance. Old hose-sets should not be reused.
08 Before use Delay Power Heavy Sport wash Silent Quick Spin S e l f - c l e a n W ash Rinse Spin T emp. Speed Auto Silk W ool Synthetic Memory Cotton Star t/ Pause Press and hold 2seconds to set door.
09 Before use F Display screen _Display washing time, remaining time, times of rinsing, spinning time, temperature setting value, speed setting value, position of clothes weight, child lock state, door lock state, washing progress and alarm message, etc.
2 1 Detergent compartment for prewash mode 2 Detergent compartment 3 Compartment for softener and other additives 2 1 1 3 2 10 using the APPLiAnCe progrAm selection PROGRAM MODES Preset spin speed Pro.
11 using the APPLiAnCe consumption AnD technicAl DA t A TECHNICAL DA T A CONSUMPTION T ABLE The wash cycle times are intended as a guide only . The actual time used may vary due to different water pressure, initial water temperature, etc. PROGRAM MAX.
12 using the APPLiAnCe W Ashing methoDs POWER SUPPL Y Connect the washing machine to the power supply (220V to 240V~/50Hz). W A TER CONNECTION T urn on the tap. The water must be clean and clear . Note: Before use, check for leakage in the joints between the tap and the inlet hose by turning on the tap.
13 using the APPLiAnCe LOADING THE MACHINE Open the washer door , put in the laundr y piece by piece. Close the door tightly . ¬ When first using the washing machine, let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing machine.
Delay Power Heavy Sport wash Silent Quick Spin Self-clean W ash Rinse Spin T emp. Speed Auto Silk W ool Synthetic Memory Cotton Star t/ Pause Press and hold 2seconds to set door unlocked HW80-I1486 De.
15 using the APPLiAnCe Bed sheet (single) Cotton Approximately 800g Blanket Wool Approximately 3000g Blended fabric clothes / Approximately 800g Jackets Cotton Approximately 800g Jeans / Approximately.
16 1. 2. 1 . 2. maintenance cleAning & cAre AFTER W ASHING T urn off the water supply and pull out electricity plug after each wash. Open the washer door to prevent formation of moisture and odours. If the washing machine is left idle for a long period, drain the water in the machine and replace the drain hose.
17 Delay Power Heavy Sport wash Silent Quick Spin Self-clean W ash Rinse Spin T emp. Speed Auto Silk W ool Synthetic Memory Cotton Star t/ Pause Press and hold 2seconds to set door unlocked HW80-I1486.
18 maintenance DisplA y coDes DISPLA Y CODES AND SPECIAL FUNCTIONS ¬ Control panel lock function: Press the "Delay" and the "Start/Pause" buttons simultaneously for 3 seconds after starting a program. It can no longer be changed by operating buttons or knobs.
19 maintenance troubleshooting TROUBLESHOOTING The following circumstances do not constitute problems. Do not contact the Service Center until the problem has been confirmed. PROBLEM CAUSES SOLUTIONS Washing machine fails to operate. ¬ Poor connection to the power supply .
WIRING CIRCUIT 20 WIRING CIRCUIT FA:Anti-jamming suppresser BIX ： drain mo tor EVPX ： pr ewash Wat er in le t val v e EVFX ： mainwash Water inle t valve driving board N G L display board heating.
An important point after buying a device Haier HW701286 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Haier HW701286 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Haier HW701286 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Haier HW701286 you will learn all the available features of the product, as well as information on its operation. The information that you get Haier HW701286 will certainly help you make a decision on the purchase.
If you already are a holder of Haier HW701286, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Haier HW701286.
However, one of the most important roles played by the user manual is to help in solving problems with Haier HW701286. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Haier HW701286 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
