Instruction/ maintenance manual of the product AD2096A American Dynamics
Go to page of 24
Installation and Operating Instructions This manual describes the installation and operating procedures for the American Dynamics AD2096A Alarm Interface Unit.
The software/firmware furnished with this equipment is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software/firmware is furnished to the purchaser under a license for use on a single system.
The installation of this product should be made by qualified service personnel and should conform to all local codes. QA301D ! W W W W A A A A R R R R N N N N II I I N N N N G G G G To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.
.
CONTENTS Page DESCRIPTION .............................................................................. 1 FEA TURES .................................................................................... 1 INST ALLA TION ................................
.
DESCRIPTION The AD2096A Alarm Interface Unit (AIU) is used with American Dynamics Matrix Switching Systems to provide automatic callup of a camera to a monitor when a specific alarm switch/contact input is activated. Each AD2096A AIU is set up to identify the matrix system video input and preset scenes with which it will be associated.
SETUP Three 8-position DIP switches are used for AD2096A setup. The first two switches, S1 and S2, are located on the rear panel (see Figure 1, page 1). The top switch, S1, identifies the block of 64 alarm contacts (out of a possible 1024) which are connected to the AD2096A.
CONNECTIONS Alarm Inputs Eleven 12-pin connectors are provided on the rear panel of the AD2096A for alarm inputs. A mating screw-terminal connector, below, is supplied for each rear panel connector. Each connector is labeled with an alarm number (1 - 64), an "A", and a ground symbol.
OPERATION Power Sources Power is supplied via the appended 3-wire power cord. Power consumption is approximately eight watts. The AD2096A is configured for 120VAC, 50/60Hz, primary power source. Operating power voltages must be held within the 105V and 125V range.
T ypical System Connections.
.
ABCDEFGH ON OFF ON OFF SELECT ALARM POWER C O M INPUT OUTPUT ABCDEFGH N N C O C M 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 25 26 27 28 2.
ABCDEFGH ON OFF ON OFF SELECT ALARM POWER C O M INPUT OUTPUT ABCDEFGH N N C O C M 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 25 26 27 28 2.
AD1996 AD2096A AUX START RELAY OUTPUT SELECTS ALARM GROUP # 1-64, 65-128, 129-192 etc.... NORMALLY OPEN/CLOSED POSITION FOR ALARM INPUTS 1-8, 9-16, 17-24 etc.
C-5 TYPICAL SYSTEM CONNECTIONS AD2096A TO AD2150/2350 AD2150/2350 RS232 PORTS MONITORS 12 3 4 5 123 ALARMS RELAY KEYBOARDS 23 4 5 CAMERAS CODE 120V 60Hz BWS BWS BWS BWS 2468 1 0 1 2 1 4 1 6 1 8 2 0 2 2 2 4 2 6 2 8 3 0 3 2 13579 1 1 1 3 1 5 1 7 1 9 2 1 2 3 2 5 2 7 2 9 3 1 AD2096A SELECTS ALARM GROUP # 1-64, 65-128, 129-192 etc.
TYPICAL SYSTEM CONNECTIONS Cascading Multiple AD2096A Units AD2096A AD2096A 6003-0047-02 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 TERMINAL BOX 2113-0019-01 BROWN (GRD) GREEN RED GREEN BROWN (GRD) RED TERMINAL .
241 AD2010 Switching Bay PORTS 120V 60Hz DATA LINE 12 PROG MON 12 34 56 78 9 1 0 AD1996 1 AD2010DBVL Module 12 3 4 5 6 7 8 12 3 4 5 6 7 8 DATA LINE IN OUT SYNC 120 VAC 50/60 Hz 1 17 33 49 65 81 97 113.
Index.
.
I-2 INDEX AD2096A Alarm Input Connections . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Alarm Relay Output Connection . . . . . . . . . . . . . . . . . . . . . 3 Alarm Response Operation . . . . . . . . . . . . . . . . . . . . . . . . . 4 Baud Rate Setup .
.
DECL ARA TION OF CONFORMITY According to ISO/IEC G uide 22 and EN45014 Manufacturer’s N ame: Sensormatic Electr oni cs Corporation Manufacturer’s A ddress: 1 Blue Hill Plaza 2 nd Floor Pearl River.
Sensormatic Video Systems Division One Blue Hill Plaza Pearl River, New York 10965 (845) 624-7600 Technical Support Center: 1-800-442-2225 FAX: 845-624-7685 8000-1819-01, Rev A December, 2000 Printed .
An important point after buying a device American Dynamics AD2096A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought American Dynamics AD2096A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data American Dynamics AD2096A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, American Dynamics AD2096A you will learn all the available features of the product, as well as information on its operation. The information that you get American Dynamics AD2096A will certainly help you make a decision on the purchase.
If you already are a holder of American Dynamics AD2096A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime American Dynamics AD2096A.
However, one of the most important roles played by the user manual is to help in solving problems with American Dynamics AD2096A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device American Dynamics AD2096A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
