Instruction/ maintenance manual of the product AD1650B American Dynamics
Go to page of 56
AD1650B MicroPower EP V ideo Matrix Switching System This manual describes the installation procedures for the American Dynamics model AD1650B MicroPower EP Video Matrix Switching Systems. The AD1650B is a CCTV surveillance control system having multiple video inputs, multiple video outputs, and multiple control stations.
The software/firmware furnished with this equipment is confidential to and is copyrighted by AMERICAN DYNAMICS. It is not to be copied or disclosed in any manner without the express written consent of AMERICAN DYNAMICS. The software/firmware is furnished to the purchaser under a license for use on a single system.
The installation of this product should be made by qualified service personnel and should conform to all local codes. QA301C Warning: This product generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications.
.
CONTENTS Page SYSTEM DESCRIPTION ................................................................................ 1 MODULE DESCRIPTIONS ............................................................................ 2 SETUP Central Processing Module ....
.
SYSTEM DESCRIPTION The AD1650B MicroPower EP Matrix Switching System is a CCTV control system with multiple video inputs, multiple video outputs, and multiple control stations. The AD1650B is capable of controlling a maximum of 128 video input sources such as cameras, a maximum of 16 video outputs such as monitors, and a maximum of 24 keyboards.
SYSTEM MODULE DESCRIPTIONS Power Supply Module - AD1603N The AD1603N Power Supply Module (PSM) converts the input AC power to the necessary DC voltages which are supplied to all the modules in the AD1650B bay. In multiple bay systems, the AD1603N PSM also provides power to bays that do not have a Power Supply Module.
Terminating Video Input Module - AD1611 The AD1611 Video Input Module (VIM) performs the actual video switching in the AD1650B switching bays. Each module can switch any one of eight video inputs to any video output, or multiple combinations of video outputs, up to eight.
.
SETUP This section of the manual describes the module setup procedures for the AD1650B System. All AD1650B systems are factory configured for proper operation. However , it may be necessary to change or adjust the factory setups to certain modules for unique or changing user requirements.
SETUP Central Processing Module - Video Type Selection A DIP switch, labeled S2, on the AD1661B and AD1663B Central Processing Module PCB is factory set for the type of video signal. Switch position 7 of S2 is set to OFF for NTSC video and ON for PAL video.
Power Supply Module The AD1603N Power Supply Module converts the input AC power to the necessary DC voltages which are supplied to all the modules in the AD1650B bay. The AD1603N PSM also includes the Control Code circuitry which supplies code to the remote Receivers and other Control Code accessories.
.
SYSTEM INST ALLA TION This section of the manual describes the system installation and connection procedures for the AD1650B System. AD1650B Systems are supplied in completely configured switching bays.
INSTALLATION This installation should be made by qualified service personnel and should conform to all local codes. Safeguards must be taken to avoid unintentional operation by employees and maintenance personnel working about the premises, by falling objects, by customers, by building vibration, and by similar causes.
Control Code Connections The Control Code for Receivers, Code Followers/Responders, Code Distributors, Code Translators, and other code-controlled accessories is provided by Control Code Outputs in either the AD1651B, AD1653B, or AD1655 bay.
System Control Connections TWO-WIRE KEYBOARDS Eight 2-wire keyboard ports are provided on the rear panel of the AD1661B or AD1663B CPM (see rear panel illustrations on page 2). The port number labels on the rear panel, 1 - 8, correspond to the monitor number controlled via that port.
SYSTEM CONFIGURA TIONS The following section of this manual provides interconnection information for typical configurations of the AD1650B system. These are organized according to the size and capabilities of systems. System Configurations . . . . . .
SYSTEM CONFIGURATIONS The following section of this manual provides interconnection information for typical configurations of the AD1650B system. These are organized according to the size and capabilities of systems, as follows: 1. Single Bay systems page 3-3 - up to 56 x 2, 48 x 4, 40 x 6, or 32 x 8 (Cameras x Monitors) 2.
SINGLE BAY SYSTEMS Single bay systems can consist of 56 cameras and 2 monitors, 48 cameras and 4 monitors, 40 cameras and 6 monitors, or 32 cameras and 8 monitors.
TWO BAY SYSTEMS, 64 CAMERAS x 8 MONITORS Systems for a maximum of 64 cameras and 8 monitors are supplied in two bays. The AD1653B bay contains a power supply, processor, and monitor modules for monitors 1 through 8. The AD1654 bay contains the the camera modules for cameras 1 through 64.
THREE BAY SYSTEMS, 128 CAMERAS x 8 MONITORS Systems for a maximum of 128 cameras and 8 monitors are supplied in three bays. The AD1653B bay contains a power supply, a processor, and monitor modules for monitors 1 through 8. The AD1654 bay contains the camera modules for cameras 1 through 64.
THREE BAY SYSTEMS, 128 CAMERAS x 8 MONITORS (Continued from prior page) Video Input Connections Each AD1611 VIM in the AD1654 and AD1655 bays includes eight terminated BNC’s for video input connections. The system assigns the video input connected to the top BNC on the right-most AD1626 VIM in the AD1654 bay as input number 1.
TWO BAY SYSTEMS, 24 CAMERAS x 16 MONITORS Systems for a maximum of 24 cameras and 16 monitors are supplied in two bays. The AD1653B bay contains a power supply, a processor, camera modules for cameras 1 through 24, and monitor modules for monitors 1 through 8.
FOUR BAY SYSTEMS, 64 CAMERAS x 16 MONITORS Systems for a maximum of 64 cameras and 16 monitors are supplied in four bays. The AD1653B bay contains a power supply, processor, and monitor modules for monitors 1 - 8. The AD1657 bay contains a power supply and monitor modules for monitors 9 - 16.
Video Input Connections Each AD1609CM in the AD1656 bay has eight pairs of looping BNC’s on the back panel for video input connections. Video inputs are connected to one BNC of each pair and looped to the corresponding terminated video input in an AD1611 VIM in the AD1654 bay.
SIX BAY SYSTEMS, 128 CAMERAS x 16 MONITORS Systems for a maximum of 128 cameras and 16 monitors are supplied in six bays. The AD1653B bay contains a power supply, processor, and monitor modules for monitors 1 through 8; the AD1657 bay contains a power supply and monitor modules for monitors 9 through 16.
Video Interconnections (continued) AD1654 to AD1653B - Connect the top BNC on the AD1654 bay VIP Panel, labeled 1, to the top input BNC of the AD1653B bay VOM panel for system monitor 1, labeled MONITOR 1 A. Connect the BNC labeled 2 on the AD1654 bay VIP panel, to the top input BNC of the AD1653B bay VOM panel for system monitor 2, labeled 2 A.
.
OPERA TION The following section of this manual describes the powering up and basic operation of the AD1650B system. The complete system setup programming and operating instructions for the AD1650B are provided in the System Programming manual, OP1650BSP .
POWERING UP A complete AD1650B system may be brought on-line after: • All modules and bays have been installed and connected. • One or more cameras have been connected for video input. • One or more monitors have been connected for viewing video output.
KEYBOARD CONTROL The following instructions are for verifying basic operation of the system. For complete setup and programming of the AD1650B, refer to the AD1650B System Programming Manual, OP1650BSPB. All system setup and control functions are accessible through keyboards connected to the system.
IF YOU ENCOUNTER ANY PROBLEMS OPERATING THIS UNIT, OR NEED ASSISTANCE, CALL OUR TECHNICAL SUPPORT CENTER: within the United States: 1-800-442-2225 outside the United States: (914) 624-7640.
TYPICAL SYSTEM CONNECTIONS T ypical System Connections AD1672 Keyboard to AD1650B . . . . . . . . . . . . . . . . . . . . . C-2 AD1676 Keyboard to AD1650B . . . . . . . . . . . . . . . . . . . . . C-3 AD2078 Keyboard to AD1650B . . . . . . . . . . . .
C-2 TYPICAL SYSTEM CONNECTIONS AD1672 KEYBOARD TO AD1650B AD1650B AD1672 NOTE: THESE CONNECTIONS, ILLUSTRATING CONTROL OF MONITORS 1 AND 2, ARE TYPICAL OF ONE KEYBOARD. ANY TWO MONITORS CAN BE CONTROLLED BY ONE AD1672 KEYBOARD. MULTIPLE AD1672 KEYBOARDS CAN BE CONNECTED TO AD1650B PORTS TO CONTROL ADDITIONAL MONITORS.
RS-232 12 34 J1 OUT PGM MON 7 6 5 4 3 2 1 8 K E Y B R D TYPICAL SYSTEM CONNECTIONS AD1676 KEYBOARD TO AD1650B C-3 RCD XMIT GND NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE KEYBOARD. EACH RS232 PORT IS PROGRAMMABLE. TP8059 7.5 VOLTS AC 1.
RS-232 12 34 J1 OUT PGM MON 7 6 5 4 3 2 1 8 K E Y B R D C-4 TYPICAL SYSTEM CONNECTIONS AD2078 KEYBOARD TO AD1650B AD2078 JJ0007 JJ0007 HP0082 TERMINAL BLOCK TP8082 or TP8083 Wall Transformer AD1650B NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE KEYBOARD.
18 AWG SHIELDED TWISTED PAIR , BELDEN 8760 OR EQUIVALENT TYPICAL SYSTEM CONNECTIONS AD1691 CODE DISTRIBUTOR TO AD1650B C-5 NOTE: THESE CONNECTIONS ARE TYPICAL OF ONE CODE DISTRIBUTION UNIT SWB A C A C.
RS-232 12 34 J1 OUT PGM MON 7 6 5 4 3 2 1 8 K E Y B R D TYPICAL SYSTEM CONNECTIONS AD2096 ALARM INTERFACE TO AD1650B C-6 NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE ALARM INTERFACE, EACH RS232 PORT IS PROGRAMMABLE.
RS-232 12 34 J1 OUT PGM MON 7 6 5 4 3 2 1 8 K E Y B R D TYPICAL SYSTEM CONNECTIONS 2096 ALARM INTERFACE TO 1650B C-7 AD2096 NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE ALARM INTERFACE, EACH RS232 PORT IS PROGRAMMABLE.
TYPICAL SYSTEM CONFIGURATIONS SINGLE BAY, 32 Cameras, 8 Monitors C-8 32 INPUTS FROM CAMERAS PROGRAMMING MONITOR 8 OUTPUTS TO MONITORS 81 1 32 AD1651 BAY RS-232 J1 OUT 12 34 MONITOR 87 O U T O U T A A .
TYPICAL SYSTEM CONFIGURATIONS TWO BAYS, 64 Cameras, 8 Monitors C-9 C A M E R A 2 5 2 8 2 9 3 2 C A M E R A 1 7 2 0 2 1 2 4 C A M E R A 9 1 2 1 3 1 6 C A M E R A 1 4 5 8 C A M E R A 5 7 6 0 6 1 6 4 C A.
TYPICAL SYSTEM CONFIGURATIONS THREE BAYS, 128 Cameras, 8 Monitors C-10 C A M E R A 2 5 2 8 2 9 3 2 C A M E R A 1 7 2 0 2 1 2 4 C A M E R A 9 1 2 1 3 1 6 C A M E R A 1 4 5 8 C A M E R A 5 7 6 0 6 1 6 4.
TYPICAL SYSTEM CONFIGURATIONS TWO BAYS, 24 Cameras, 16 Monitors C-11 24 INPUTS FROM CAMERAS AD1653 BAY AD1657 BAY 1 8 24 1 PROGRAMMING MONITOR 9 16 8 OUTPUTS TO MONITORS 24 LOOPING INPUTS FROM AD1657 .
TYPICAL SYSTEM CONFIGURATIONS FOUR BAYS, 64 Cameras, 16 Monitors C-12 C A M E R A 2 5 2 8 2 9 3 2 C A M E R A 1 7 2 0 2 1 2 4 C A M E R A 9 1 2 1 3 1 6 C A M E R A 1 4 5 8 C A M E R A 5 7 6 0 6 1 6 4 .
J1 OUT 2 5 3 2 5 7 6 4 4 9 5 6 4 1 4 8 3 3 4 0 9 1 6 1 8 1 7 2 4 V I P 9 11 13 15 10 12 14 16 MONITOR 21 O U T A A B B O U T MONITOR 43 O U T A A B B O U T MONITOR 6 5 O U T A A B B O U T MONITOR 8 7 .
.
INDEX.
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AD1603N PSM, Power Supply Module . . . . . . . . . . . . . . . 2 AD1609CM, Video Input Module . . . . . . . . . . . . . . . . . . . 3 AD1611, Video Input Module . .
Three Bays, 128 Camera, 8 Monitor Systems . . . . . . . . . 3-5 Two Bays, 64 Camera, 8 Monitor Systems . . . . . . . . . . . 3-4 Two Bays, 24 Camera, 16 Monitor Systems . . . . . . . . . . 3-7 TYPICAL SYSTEM CONNECTIONS . . . . . . . . . . . . . C-1 Vertical Phase Adjustment, Power Supply Module .
.
Declaration of Conformity Manufacturer: Sensormatic CCTV Systems Division Manufacturer’s Address: Sensormatic CCTV Systems Division 10 Corporate Drive Orangeburg, New York 10962 USA Sensormatic Electronics Corporation American Dynamics Business Unit State Rd.
Additional information: These products herein, comply with the requirements of the EMC Directive 89/336/EEC. The equipment was tested in a typical configuration.
.
An American Dynamics Product Designed and built by Sensormatic CCTV Systems Division One Blue Hill Plaza Pearl River, New York, 10965 (914) 624-7600 Technical Support Center: 800-442-2225 FAX: (914) 624-7685 8000-0869-01 OP1650BG June 1996 Printed in USA SPECIFICATIONS Supply Voltage: Power per Bay: 35 watts max.
An important point after buying a device American Dynamics AD1650B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought American Dynamics AD1650B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data American Dynamics AD1650B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, American Dynamics AD1650B you will learn all the available features of the product, as well as information on its operation. The information that you get American Dynamics AD1650B will certainly help you make a decision on the purchase.
If you already are a holder of American Dynamics AD1650B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime American Dynamics AD1650B.
However, one of the most important roles played by the user manual is to help in solving problems with American Dynamics AD1650B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device American Dynamics AD1650B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
