Instruction/ maintenance manual of the product HA600TE Haier
Go to page of 18
Automatic Drum W ashing Machine HA1000TE HA800TE HA600TE T able of Contents Before using Names of Parts---------------------------------inside front cover Matters Needing Attention--------------------.
Names of Parts T able Cover Program Knob Operation Button Drainage hose clip Back plate Packing bolt (3) W ashing Allocating box W ash Door Observing Glass Window Drainage hose Earth terminal Power su.
Safety 1. A separate earthed socket is required for the power supply . After installation of the washing machine,the power plug should be accessible during the normal wash. 3. Fuses in the power circuit should be rated for 15A. Refer to a washing machine techni- cian or a Haier designated service point for power cable replacement.
Matters Needing Attention 2 Use ƽ.
9. Keep the door slightly open when the washing machine is not being used. Never cover the machine with a plastic sheet. 4. Do not wash foam rubber or similar sponge materials. 5. Before washing, do up zippers, buttons , laces and repair damaged areas,under- wear or small articals should be placed in the laundry bag or a pillowslip.
As shown in figure1 remove all the packing materials (including the foam base). Fig 1 Check attachments and materials. 3 Name Qty Model Operational manual Quality certificate Wa t e r hose Drainage holder Plastic plugs 1 1 1 HA1000TE HA800TE HA600TE 1 Remove the packing screws as shown in figure 2.
Connection of water inlet hose and washing machine W a t e rd r a i n a g eh o s e Connection of power supply The height of the terminal of the water drainage hose should be between 80cm-100cm, the water drainage hose must be securely placed on the clip on the back of the washing machine.
6 Control Panel T urn the knob at "0", then turn of f the power and turn the program knob for setting desired wash program. The program knob will not rotate with the programmed washing process.
7 Operational Functions Economic W ash button Note: Select this function when "Cotton" "Synthetics", "Wool" or "Silk" (programs 1-12) is selected.
Program Selection 8 Intense Prewash Normal Middle Delicate Normal Middle Delicate Normal Delicate Normal Delicate Silk 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7 V ery heavy soil Non-fade heavily soiled wo.
1. Power supply Plug in the power supply 220V~240V/50Hz. 3. Laundry treament 5.W ash Load 2. W ater supply T urn on the tap ensure that the water is clear . Caution: Before staring the washing machine turn on the water faucrt to ensure that the water faucet and the water inlet hose are connected correctly and do not leak.
1. Laundry loading Evenly load the laundry in the washing machine and then tightly close the door of the washing machine Note: 1) When first using the washing machine, let it run un- loaded for one program to pre- vent the laundry from being tainted by oil or dirty water from the washing machine.
11 7. End W ait 2-3 minutes after the washing process is finished , press the power button again to cut off the power supply . Open the door to take out the laundry .
Other Functions 1. Power-off memory funtion: This machine has a power-off menmory funtion. In case of abrupt power failure or the power must be cut off during a program cycle, the present settings will be saved, and operation will resume when the power is switched on again.
Insert the bolts. 5. If the machine is to be moved a distance location, replace the vibration mounting locks which were re- moved during installation as shown below. 1. T urn of the water and electricity supply af- ter every wash. Open the door to prevent the formation of moisture and odors.
The following circumstances do not constitute problems. Do not contact the maintenance service until the problem has been confirmed. Problem Possible Cause The washing machine fails to operate Poor co.
Maximum power (W) Model Maximum working current (A) W ater pressure (MPa) W ashing power (W) Spinning power (W) Max. washing load (kg) Spinning speed (r/min) Size (mm) W eight (kg) HA1000TE 220V~240V/50Hz 15 0.03 P 1 230 400 5 15 2000 65 1000 850x520x595 Item Power supply W ashing program T echnical Specification HA 8 00TE 220V~240V/50Hz 15 0.
W iring Circuit 16 Motor R S T M1 M2 M3 M5 M7 M8 CN1-2 CN2-1 CN1-3 CN1-1 CN3-3 CN3-1 CN2-2 CON3 CN2-3 CN2-4 CN2-5 CN2-6 CON3 CN3-3 CN3-4 CON2 CON1 CN6-3 CN6-4 PCB NTC SW N G L FA MRN MRL MRC MR EVF EV.
An important point after buying a device Haier HA600TE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Haier HA600TE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Haier HA600TE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Haier HA600TE you will learn all the available features of the product, as well as information on its operation. The information that you get Haier HA600TE will certainly help you make a decision on the purchase.
If you already are a holder of Haier HA600TE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Haier HA600TE.
However, one of the most important roles played by the user manual is to help in solving problems with Haier HA600TE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Haier HA600TE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
