Instruction/ maintenance manual of the product 0030808445 Haier
Go to page of 18
User's manual This manual is for HWM1 10-287S Please read this manual carefully before using. Retain it for future reference. T win-tub Washing Machine 0030808445.
Contents Names of the parts - - - - - - - - - - - - - - - - - 1 Safety precautions - - - - - - - - - - - - - - - - - 2 Installation and adjustment - - - - - - - - - - - 4 Preparation before washing - .
ºó¸Ç Ë®µÀ Major frame Base frame W ater-filling entrance W ash selector W ash timer Control panel W ater level adjusting lever Pulsator W ash tub W ash tub cover Drain hose Overflow filter V a.
Safety precautions Please insert the power cord into special receptacle with rated vol- tage. Be sure to use single-phase three pins receptacle. The earthing terminal of the receptacle must be earthed reliably. If possible, please adopt electric leakage protector.
Please don t use the washer in the environment below 0 C. If the washer is below 0 C, the washer s water inlet system and draining system will be frozen ,then result in the damaged of the whole machine. If the washer has below 0 C, please be sure to ensure the washer is placed under the room temperature for 2~4 hours and then use .
Installa tion and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. 4 Usage of the drain hose If the extra hose is too long, cut it either at point A or B.
5 How to change the direction of the drain hoses Figure 1 indicates the ex factory installation position of the drain hose. Figure 1 Figure 2 Drain h ose fixing h ook Side sectional v iew Drain h ose .
Pr epar a tion bef or e washing 6 Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe.
The musts in washing 7 The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity.
Washing sequence 8 Spin timer Wa sh timer (T o set to below 2 minute, first set to 6 minute then turn it back. it can increase the service life of the timer). (to set to below 1 minute, first set to 2 minute then turn it back. it can increase the service life of the timer).
Ï´µÓÐëÖª Midway spinning Push Push Proper Proper Outer cover of The spin tub Inner cover of The spin tub The laundries are slanting Gland No gland (1) Set the water-filling selector control rod at the "SPIN" side. Fill water for about 1 minute.
Rinse with stored water Rinse with water-filling 1. Put the laundries into the wash tub. Select suitable current according to the laundries. 2. Fill water to preset water level. 3. Rinse Adjust the wash timer to 2-3 minutes to do rinsing. When the laundries quantity is a few , please use "Standard" current.
1. Put the laundries into the spin tub evenly and smoothly. 2. Press the gland in the tub properly. Close the inner and outer cover of the spin tub. 3. Spin Select suitable spin time according to the laundries, and do spinning. During spinning, if there's abnormal sound, it is generally owing to slanting placement of the laundries.
After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine.
Wipe the complete unit with soft cloth twisted dry. Wipe with neutral detergent if too dirty Do not wash it directly by water Cleaning the overflow filter 2. T ake off the corrugation pipe. Dismantle the upper part of the corrugation pipe inside the overflow filter ( as indicated in Figure 1).
When the remained water is frozen Prevent the freezing (be sure to discharge the water completely after using) After complete draining, set the "WASH SELECTOR" at "STRONG" or "STANDARD". If it is set at "DRAIN", it will be rather difficult for the frozen water to melt.
T r ouble-shooting Ans wer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company.
W ater inlet hose Gland Packing list Twin-tub washing machine Name Quantity User's manual One piece One piece One piece One set 16 Speciafication W ater level/Water quantity (L) (about) Maximum/70 Medium/60 Minimum/50 Injection pressure(MPa ) Washing capacity(kg) 8.
An important point after buying a device Haier 0030808445 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Haier 0030808445 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Haier 0030808445 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Haier 0030808445 you will learn all the available features of the product, as well as information on its operation. The information that you get Haier 0030808445 will certainly help you make a decision on the purchase.
If you already are a holder of Haier 0030808445, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Haier 0030808445.
However, one of the most important roles played by the user manual is to help in solving problems with Haier 0030808445. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Haier 0030808445 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
