Instruction/ maintenance manual of the product Professional Power Amplifier American Audio
Go to page of 16
User Instructions AMERICAN AUDIO ® 4295 Charter Street Los Angeles Ca. 90058 Revised 02/02 Pr ofessional Power Ampli ers .
This symbol is intended to alert the user to the presence of non insulated "danger ous voltage" within the product's enclosur e that may be of suf cient magnitude to constitute a risk of electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. THERE ARE NO USER SERVICEABLE P ARTS INSIDE. REFER ALL SERVICE TO YOUR AUTHORIZED AMERICAN AUDIO ® DEALER.
Important Pr ecautions • T o reduce the risk of electrical shock or r e, do not expose this unit rain or moisture • Do not spill water or other liquids into or on to your unit • Do not attem.
FRONT P ANEL 1. Power Switch - This switch controls the units main power . 2. Channel 1 Limiter Switch (V2000 & V3000 Only) - This is used to activate the channels built-in limiter . The limiter reduces the average output level when the signal begins to distort, this process is designed to reduce distortion and pr otect the speakers.
V1000 plus V1000 plus V1000 REAR P ANEL 1. Channel 2 Input - Connect the input source for channel two to either the balance XLR or the balanced/unbalanced 1/4” input jacks. The 1/4” TRS plug is configured as follows; Tip is positive, Ring is negative and Sleeve is ground.
V2000 plus V2000 plus V2000 REAR P ANEL 1. Cooling Fan - Dual speed cooling fans. These fans are used to cool the inter nal parts of the amplifier . Never block the fan grills in any way or mount in an en- close rack, doing so may cause the amplifier to overheat and fail.
V3000 plus V3000 plus V3000 REAR P ANEL 1. Cooling Fan - Dual speed cooling fans. This fans are used to cool the internal parts of the amplifier when in use. Never block the fan grills in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail.
Unbalanced TS 1/4” Unbalanced TS 1/4” Plug Plug Hot (+) Ne gati ve (-) Balanced TRS 1/4 Balanced TRS 1/4 ” Plug Ground/Shield Hot (+) Ne gati ve (-) 2 Hot (+ data) 3 Ne gati v e (- data) 1 Groun.
Bar e Wire Connections: When connecting your speakers to the amplifier using bar e wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. Strip back the wire insulation 1/2” (13mm).
TYPICAL MONO BRIDGE SET -UP SPEAKERS 8 OHM MINIMUM T ypical Stereo Output Connections T ypical Stereo Output Connections Diagram 14 Diagram 13 SPEAKERS 4 OHM MINIMUM SPEAKERS 4 OHM MINIMUM 1000 W A 10.
1 2 3 4 T ypical Ster eo Set-Up T ypical Mixer V3000 plus V3000 plus V3000 series (Rear View) T ypical Speaker Connect to Vplus series Channel One Output T ypical Speaker Connect to Vplus series Channel T wo Output Output Diagram 15 American Audio ® - www .
OPERATING MODES: Stereo Operation - Page 10/Figure 9 details an example of a typical stereo set-up. Connect your inputs into channels one and two of the amplifier. Connect your speakers to the outputs on the rear of the amplifier. Be sure that your front gain controls are turned down to their lowest level (full counter-clockwise).
goes into pr otect mode, the other side will continue to operate normally . During short circuit pr otection, the "Clip" LED and “Pr otect" LED will light simultaneously indicating amplifier fault. All channel output during the “Short Circuit Pr otection" will be interrupted (i.
Output Power: 2 ohms, 1 khz 1% THD 2 ohms, 1 khz 1% THD 2 ohms, 1 khz 1% 4 ohms, 1khz, 1% 4 ohms, 1khz, 1% 4 ohms, 1khz, 1% THD 8 ohms, 1khz 1% THD 8 ohms, 1khz 1% THD 8 ohms, 1khz 1% (Bridge Mode, mo.
©American Audio® American Audio® is part American DJ® Group of Companies American DJ® W orld Headquarters: 4295 Charter Street Los Angeles, CA 90058 USA T el: 323-582-2650 / Fax: 323-582-2610 web: www .
An important point after buying a device American Audio Professional Power Amplifier (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought American Audio Professional Power Amplifier yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data American Audio Professional Power Amplifier - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, American Audio Professional Power Amplifier you will learn all the available features of the product, as well as information on its operation. The information that you get American Audio Professional Power Amplifier will certainly help you make a decision on the purchase.
If you already are a holder of American Audio Professional Power Amplifier, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime American Audio Professional Power Amplifier.
However, one of the most important roles played by the user manual is to help in solving problems with American Audio Professional Power Amplifier. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device American Audio Professional Power Amplifier along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
