EN
Graco logo
Official user manual

Graco 2M06

16 pages·963 KB·Hot Beverage Maker·PDF·ENDEFRITNLJA
Graco 2M06
Table of Contents 11 sections Battery Installation · Using AC Adapters · Low Battery · Selecting Channels · … ShowHide
Page 1 of the Graco 2M06 user manual
Page 1 · click to enlarge
Page 1
Graco 2M06 diagram (page 1)
Fig. 1

To purchase parts or accessories or for warranty informa- tion in the United States, please contact us at the following:

the U.S.A. visit us online at www.gracobaby.com/productregistration We currently do not accept product registrations

Graco 2M06 diagram (page 1)
Fig. 2
Page 2 of the Graco 2M06 user manual
Page 2 · click to enlarge
Page 2

Failure to follow these warnings and the assembly instructions could result in serious injury or death.

This device is designed only to monitor the sounds of your child. It will not alert you to your child’s silent activities. This product is not designed or intended for use as a medical monitor. Always be sure that both the transmitter and receiver are working properly and are within range of each other.

  • STRANGULATION HAZARD. Keep the adapter cords out of the reach of children. Do not use with extension cords.
  • DO NOT place the Nursery Unit or its cord within your child’s reach. Do not put the Nursery Unit inside a crib or play yard.
  • Use ONLY with 110-120 volt AC electrical outlets.
  • Protect the AC adapter cords. Place them so they are not walked on or pinched by furniture or other items.
  • Allow for proper ventilation when units are in use. Do not cover the Nursery Unit or Parent Units with any object such as a blanket. Do not place it in a drawer or in any location which would muffle the sound or interfere with the normal flow of air.
  • DO NOT immerse any part of the Nursery Unit or Parent Unit in water. Clean only with a dry cloth.
  • DO NOT place unit near water and moisture. Do not use the Nursery Unit outdoors. Do not use the monitor near possible wet areas, such as a bathtub, shower, wash basin, sink, laundry tub, swimming pool, wet basement, etc.
  • Keep Nursery Unit away from heat sources, such as fireplaces, radiators, stoves, and TVs or other appliances. Heat can damage the case or electrical parts.
  • DO NOT use the monitor if:
  • The adapter cords or plugs have been damaged.
  • The unit has been exposed to liquids.
  • Unit has been dropped or is damaged.
  • DO NOT OPEN THE TRANSMITTER, RECEIVER OR ADAPTER. No user-serviceable parts inside. Risk of electrical shock, fire or death.

FCC Statement:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
Page 3 of the Graco 2M06 user manual — Low Battery
Page 3 · click to enlarge
Page 3

Battery Installation

The Parent Unit is shipped with rechargeable batteries already

installed. The battery must be plugged into the Parent Unit before the unit will be ready for use.

  • Remove the battery door cover on the Parent Unit with a key or flat blade screw driver.
  • Lift the battery out of the compartment, and carefully plug the battery into the unit.
  • Replace the battery and the battery door cover.
  • If it becomes necessary to purchase a new battery, remove the cover, carefully unplug the battery and replace with a new battery. Replace the battery door cover.

Using AC Adapters

  • The Parent Unit can use either the rechargeable battery that comes with the unit or standard 120 volt AC household current. The Nursery Unit uses standard 120 volt AC household current.
  • To use AC adapters, plug the connector on the cord into the AC adapter jack on the side of the Parent Unit and the Nursery Unit. Then plug adapter into a standard wall outlet.
  • Use ONLY the Graco adapters included with the unit. Do not use these adapters with other equipment under any circumstances.
  • If units do not work, check that AC adapters are plugged into working outlets.
  • When electricity is off (from a power failure, etc.), the Parent Unit will operate on rechargeable batteries, however, the Nursery Unit will not operate until power is restored.

Low Battery

  • When the battery is low in the parent unit you may plug in the A/C adapter to recharge the batteries.

Out of Range Indication

  • If the Parent Unit begins to lose the signal from the Nursery Unit you may hear static or other noise. Immediately move the Parent Unit closer to the Nursery Unit to regain connection.

***Note: It is not uncommon for the Parent Unit to occasionally lose and regain connection with the Nursery Unit in environments that have a significant amount of obstructions.

Parent Unit · Parent Unit

Page 4 of the Graco 2M06 user manual — Testing the System
Page 4 · click to enlarge
Page 4

Selecting Channels

  • In case you are experiencing some interference, the channel on the Nursery Unit can be changed by switching the channel button on the side of the unit. The Parent Unit and Nursery Unit must both be set to the same channel, either channel “A” or “B” (“X” or “Y”).

Setting Up the Baby Monitor

1. For optimum operation, it is best to use fully charged batteries in the Parent Unit. It is recommended that the batteries in the Parent Unit be charged for 16 hours prior to initial use.
2. Place the Nursery Unit within 10 feet (3 meters) of your baby. Plug an AC adapter into the jack on the side of the Nursery Unit. Plug it into a working 120 volt AC outlet.
3. Aim the Nursery Unit toward your baby. Check that there are no walls or large objects that could block sound transmission.
4. Set both the Nursery Unit and Parent Unit to the same channel, “A” or “B” (“X” or “Y”).
5. Turn on the Nursery Unit using the On/Off switch on the side. The green power light should come on.
6. Place the Parent Unit within five (5) feet (1.5 meters) of the Nursery Unit and turn on the Parent Unit using the On/Off switch on the side of the unit. The green power light should come on. Your monitor is now ready for use.

Testing the System

It is VERY IMPORTANT to test the system when first set up, and at regular times thereafter. Test the units if you

suspect they may have been damaged or have not been used for a long time.

1. If two adults are present, have one take the Parent Unit to different locations, trying various volume settings, while the other speaks into the Nursery Unit.
2. If only one adult is available, place a ticking clock, radio, or other sound-producing device near the Nursery Unit to test it.
3. When testing, keep the level of your child’s sounds in mind, and adjust the volume accordingly.
4. If there is sound interference, switch the Nursery Unit and the Parent Unit to the other channel setting.
Page 5 of the Graco 2M06 user manual — Clock and Timer
Page 5 · click to enlarge
Page 5

Operation

To Listen To Baby

  • Turn on Nursery Unit using the ON/OFF switch.
  • Turn on Parent Unit using the ON/OFF switch.
  • Adjust the volume on the Nursery Unit and Parent Unit by turning the Volume Up/Down knob.
  • The Sound Lights on the Parent Unit will illuminate as your child (or other objects) make noise near the Nursery Unit. Please note that the Sound Lights and volume control on the Parent Unit are independent of each other. When the volume is turned all the way down, the Sound Lights will still illuminate as your child (or other objects) make noise near the Nursery Unit.

Clock and Timer

To Set Clock:

  • When the battery is first plugged in, the clock will beep and a few seconds later blink “ 12:00 ”.
  • To set the hours, push the S1 button to the desired time. A small “PM” will appear on the left side of the window to designate “pm”.
  • To set the minutes, push the S2 button to the desired time.
  • Once the correct time is displayed in the window, push the S3 button to start the clock.

To Change the time:

  • To change the time push the S3 button and hold it down for 5 seconds. Repeat the steps above to change the time. Push S3 to start the clock.

Timer Feature:

To Count UP from 0 (up to 19 hours and 59 minutes):

  • Press both S1 and S2 buttons at the same time. The display will be “ 0:00 ”.
  • Press the S3 button. The word “UP” will appear on the upper right side of the window and the timer will start to count up.
  • To stop the timer push S3 again. You may stop and start the timer by pressing the S3 button.
  • To reset the timer to “ 0:00 ”, press both the S1 and S2 buttons at the same time.
  • If you want to view the clock time while in count up mode, press and hold the S1 button. Releasing the button will display the counter again.
  • To return to the clock, Push S1, S2 and S3 at the same time.

To set the alarm for a specific amount of time (up to 19 hours and 59 minutes):

  • Press both S1 and S2 at the same time. The display will be “ 0:00 ”.
  • Press the S1 button to set the hours up to 19 hours.
  • Press the S2 button to set the minutes up to 59 minutes.
  • Press the S3 button. The word “DOWN” will appear in the lower right corner of the window and the colon will blink.
  • When the alarm sounds press the S3 button to stop the beep.
  • To reset the alarm to “ 0:00 ” press the S1 and S2 buttons at the same time.
  • If you want to view the clock time while in count down mode, press and hold the S1 button. Releasing the button will display the counter again.
  • To return to the clock, Push S1, S2 and S3 at the same time.
Page 6 of the Graco 2M06 user manual — Music
Page 6 · click to enlarge
Page 6

To Record a Message

To Record a Message

  • Turn the Nursery Unit on and set to the desired sound level.
  • Slide the “ON/OFF Sensitivity Selector” button on the back of the Nursery Unit to “OFF” and the “Record/Melody Selector” button on the top of the Nursery Unit to “RECORD”.
  • Push and hold the “RECORD” button on the back of the Nursery Unit. Record a message up to 15 seconds long. Release the button when you are done. When the unit beeps, the record time has ended.

To Play back the Message or a Chosen Melody

Your Nursery Unit is equiped with a sensor that will trigger the unit to play either the message or one melody if the volume of

noise around the unit is sufficient to trigger the sensor. There are two settings. When the “ON/OFF Sensitivity Selector” button on the back of the Nursery Unit is switched to the “LOW” setting, the sensor will detect low sounds near the Nursery Unit and will trigger the unit to play the message or one melody. The “HIGH” setting will detect only the higher sounds near the Nursery Unit and trigger the unit to play the message or one melody.

  • Turn the Nursery Unit on and set to the desired sound level.
  • Slide the “Record/Melody Selector” button on the top of the Nursery Unit to “RECORD”.
  • Slide the “ON/OFF Sensitivity Selector” button on the back of the Nursery Unit to “LOW” or “HIGH”.
  • The “Record/Melody Selector” button on the top of the Nursery Unit can also be set to the “MELODY” setting. If the sensor detects sound, the unit will play one melody and then turn off. If the sound near the Nursery Unit continues, the unit will play the next melody. This will continue as long as the sensor detects the sound.

Music

  • To play music, slide the “ON/OFF Sensitivity Selector” button on the back of the Nursery Unit to “OFF” and the “Record/Melody Selector” button on the top of the Nursery Unit to “MELODY”.
  • Press the “PLAY” button no the back of the Nursery Unit. One of four tunes will begin to play. To select a specific tune, push the “PLAY” button until the desired tune is on. The Nursery Unit will play one song and then shut off automatically.
Page 7 of the Graco 2M06 user manual — TroubleShooting
Page 7 · click to enlarge
Page 7

TroubleShooting

DO NOT ATTEMPT to modify the unit. Any modifications to the transmitter and/or receiver can void the

operator’s authority to operate the equipment.

Most problems have a simple solution. First, check that:

  • Power is turned ON for both units
  • Both units are plugged in (or batteries are recharged in Parent Unit)
  • Electrical outlet works
  • Volume is turned up on Parent Unit
  • Parent Unit is in range of the Nursery Unit
  • Battery dead or weak — recharge battery or use AC adapter.
  • AC adapter not properly connected — check the connections.
  • Nursery Unit covered or blocked — remove the obstruction.
  • Nursery Unit too far from baby — move closer.
  • Large objects blocking the signal — try repositioning Nursery Unit.
  • Volume setting too low — turn it up.
  • Interference from other electrical equipment — eliminate cause of static (TVs, mixers, computers, fans, fluorescent lights, light dimmers, etc.)
  • Parent Unit too far from Nursery Unit — move them closer.
  • Significant amount of obstructions between Parent Unit and Nursery Unit such as walls, ceilings & buildings. Try moving the Nursery Unit to another part of the room.
  • Nursery Unit and Parent Unit too close together — move them farther apart.
  • Volume set too high — lower the volume.
Show 4 more labels / short text on this page
No Sound · Weak Sound · Static · Shrill Sound (Feedback)
Page 8 of the Graco 2M06 user manual — TroubleShooting
Page 8 · click to enlarge
Page 8
Page 8 of the Graco 2M06 user manual — TroubleShooting

Ask about the Graco 2M06

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Graco 2M06

Be the first to ask — other owners or our team will answer.

Original document

Graco 2M06 manual PDF

16 pages·963 KB·Hot Beverage Maker·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…