EN
Graco logo
Official user manual

Graco Ultra Max II 1095

44 pages·6.7 MB·Paint Sprayer·PDF·ENDEFRITNLJA
Graco Ultra Max II 1095
Table of Contents 21 sections Models · Warnings · Component Identification · Grounding · … ShowHide
Page 1 of the Graco Ultra Max II 1095 user manual — EN
Page 1 · click to enlarge
Page 1

Operation

695 / 795 / 1095 / 1595 / Mark IV / Mark V / Mark VII / Mark X Electric Airless Sprayers

EN

For Portable Airless Spraying of Architectural Coatings and Paints. For professional use only. Not approved for use in European explosive atmosphere locations.

3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure

Graco Ultra Max II 1095 — EN diagram (page 1)
Fig. 1
Page 3 of the Graco Ultra Max II 1095 user manual — Models
Page 3 · click to enlarge
Page 3

Models

UltraMax II, Ultimate Max II Models:

695 UltraMax, Standard, ProContractor, IronMan Models ModelVoltageStandard Hi-BoyStandard Lo-BoyProContractorIronMan 16W892120✓ 16W893120✓ 16W894120✓ 826177120✓ 826178120✓ 826179120✓ 16X656230✓ 16X657230✓ 16X658120✓ 16X659120✓ 16X660230✓ 16X811120✓ 16X812230✓ 16Y635230✓ 16Y637230✓ 16Y638120✓ 16Y639230✓ 795 UltraMax, Standard, ProContractor, IronMan Models 16W895120✓ 16W896120✓ 826180120✓ 826181120✓ 16X813230✓ 16X870230✓ 16X871230✓ 16X872120✓ 16X873230✓ 16Y895230✓ 16Y896230✓ 16Y897230✓ 16Y898120✓ 16Y899120✓ 1095 UltraMax, Standard, ProContractor, IronMan Models 16W899120✓ 16W900120✓ 16W901120✓ 826182120✓ 826183120✓ 826184120✓ 16X874230✓ 16X875230✓ 16X881230✓ 16X882120✓ 16Y829230✓ 16Y830230✓ 16Y831120✓ 16Y832230✓ 16Y833120✓ 16Y869230✓ 16Y871230✓

Models

Page 4 of the Graco Ultra Max II 1095 user manual — TexSpray Models:
Page 4 · click to enlarge
Page 4
1595 UltraMax, Standard, ProContractor, IronMan Models ModelVoltageStandard Hi-BoyStandard Lo-BoyProContractorIronMan 16W902120✓ 16W903120✓ 16W907120✓ 16W936120✓ 16W937120✓ 16W938120✓ 826185120✓ 826186120✓ 826187120✓ 826188120✓ 826189120✓ 826190120✓

TexSpray Models:

Mark IV / Mark V / Mark VII / Mark X Standard, ProContractor, IronMan Models Model NumberModelVoltageStandard Hi-BoyPro ContractorIronManFlex Plus GunBlue Texture GunHD Inline Texture Gun3/8 in. x 50ft + 1/4 in. x 3 ft whip (9.5mm x 15m + 6.4mm x 0.9m whip)3/8 in. x 100 ft + 1/4 in. x 3 ft whip (9.5mm x 30m + 6.4mm x 0.9m whip)1/2 in. x 50 ft + 3/8 in. x 12 ft whip (12.7mm x 15m + 9.5mm x 3.7m whip)1/2 in. x 100 ft + 3/8 in. x 12 ft whip (12.7mm x 30m + 9.5mm x 3.7m whip) 16W897Mark IV120✓✓✓ 16W898Mark IV120✓✓✓ 16X953Mark IV230✓✓✓ 16X954Mark IV230✓✓✓ 16X956Mark IV230✓✓✓ 16Y892Mark IV230✓✓✓ 16Y893Mark IV230✓✓✓ 16Y894Mark IV230✓✓✓ 16W905Mark V120✓✓✓ 16W906Mark V120✓✓✓ 16W939Mark V120✓✓✓ 16W940Mark V120✓✓✓ 16X944Mark V230✓✓✓ 16X947Mark V120✓✓✓ 16X965Mark V230✓✓✓ 16X966Mark V120✓✓✓ 16X967Mark V230✓✓✓ 16Y533Mark V120✓✓✓ 16Y864Mark V230✓✓✓ 16Y865Mark V230✓✓✓ 16Y866Mark V120✓✓✓ 16Y867Mark V230✓✓✓ 16Y868Mark V120✓✓✓ 16Y872Mark V230✓✓✓ 16Y874Mark V230✓✓✓ 16Y763Mark VII230✓✓✓ 16Y919Mark VII230✓✓✓ 16Y920Mark VII230✓✓✓ 16Y921Mark VII230✓✓✓ 16W908Mark X230✓✓✓ 16X099Mark X230✓✓✓ 16Y534Mark X230✓✓✓ 16Y535Mark X230✓✓✓ 16Y536Mark X230✓✓✓ 16Y910Mark X230✓✓✓ 16Y912Mark X230✓✓✓ 16Y913Mark X230✓✓✓

Models

Page 5 of the Graco Ultra Max II 1095 user manual — 120V US 230V
Page 5 · click to enlarge
Page 5

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.

WARNING

GROUNDING This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

  • Improper installation of the grounding plug is able to result in a risk of electric shock.
  • When repair or replacement of the cord or plug is required, do not connect the grounding wire to either flat blade terminal.
  • The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.
  • Check with a qualified electrician or serviceman when the grounding instructions are not completely understood, or when in doubt as to whether the product is properly grounded.
  • Do not modify the plug provided; if it does not fit the outlet, have the proper outlet installed by a qualified electrician.
  • This product is for use on a nominal 120V or 230V circuit and has a grounding plug similar to the plugs illustrated in the figure below.

120V US 230V

Graco Ultra Max II 1095 — 120V US 230V diagram (page 5)
Fig. 2
  • Only connect the product to an outlet having the same configuration as the plug.
  • Do not use an adapter with this product.
  • Extension Cords:
  • Use only a 3-wire extension cord that has a grounding plug and a grounding receptacle that accepts the plug on the product.
  • Make sure your extension cord is not damaged. If an extension cord is necessary, use 12 AWG (2.5 mm 2 ) minimum to carry the current that the product draws.
  • An undersized cord results in a drop in line voltage and loss of power and overheating.
Page 6 of the Graco Ultra Max II 1095 user manual — WARNING
Page 6 · click to enlarge
Page 6

WARNING

  • FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:
  • Do not spray flammable or combustible materials near an open flame or sources of ignition such as cigarettes, motors, and electrical equipment.
  • Paint or solvent flowing through the equipment is able to result in static electricity. Static electricity creates a risk of fire or explosion in the presence of paint or solvent fumes. All parts of the spray system, including the pump, hose assembly, spray gun, and objects in and around the spray area shall be properly grounded to protect against static discharge and sparks. Use Graco conductive or grounded high-pressure airless paint sprayer hoses.
  • Verify that all containers and collection systems are grounded to prevent static discharge. Do not use pail liners unless they are are antistatic or conductive.
  • Connect to a grounded outlet and use grounded extensions cords. Do not use a 3-to-2 adapter.
  • Do not use a paint or a solvent containing halogenated hydrocarbons.
  • Keep spray area well-ventilated. Keep a good supply of fresh air moving through the area. Keep pump assembly in a well ventilated area. Do not spray pump assembly.
  • Do not smoke in the spray area.
  • Do not operate light switches, engines, or similar spark producing products in the spray area.
  • Keep area clean and free of paint or solvent containers, rags, and other flammable materials.
  • Know the contents of the paints and solvents being sprayed. Read all Material Safety Data Sheets (MSDS) and container labels provided with the paints and solvents. Follow the paint and solvents manufacturer’s safety instructions.
  • Fire extinguisher equipment shall be present and working.
  • Sprayer generates sparks. When flammable liquid is used in or near the sprayer or for flushing or cleaning, keep sprayer at least 20 feet (6 m) away from explosive vapors.
  • SKIN INJECTION HAZARD High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that injection occurs, get immediate surgical treatment.
  • Do not aim the gun at, or spray any person or animal.
  • Keep hands and other body parts away from the discharge. For example, do not try to stop leaks with any part of the body.
  • Always use the nozzle tip guard. Do not spray without nozzle tip guard in place.
  • Use Graco nozzle tips.
  • Use caution when cleaning and changing nozzle tips. In the case where the nozzle tip clogs while spraying, follow the Pressure Relief Procedure for turning off the unit and relieving the pressure before removing the nozzle tip to clean.
  • Do not leave the unit energized or under pressure while unattended. When the unit is not in use, turn off the unit and follow the Pressure Relief Procedure for turning off the unit.
  • Check hoses and parts for signs of damage. Replace any damaged hoses or parts.
  • This system is capable of producing 3300 psi (227 bar, 22.7 MPa). Use Graco replacement parts or accessories that are rated a minimum of 3300 psi (227 bar, 22.7 MPa).
  • Always engage the trigger lock when not spraying. Verify the trigger lock is functioning properly.
  • Verify that all connections are secure before operating the unit.
  • Know how to stop the unit and bleed pressure quickly. Be thoroughly familiar with the controls.
Page 7 of the Graco Ultra Max II 1095 user manual — Warnings
Page 7 · click to enlarge
Page 7
WARNING EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • Always wear appropriate gloves, eye protection, and a respirator or mask when painting. • Do not operate or spray near children. Keep children away from equipment at all times. • Do not overreach or stand on an unstable support. Keep effective footing and balance at all times. • Stay alert and watch what you are doing. • Do not leave the unit energized or under pressure while unattended. When the unit is not in use, turn off the unit and follow the Pressure Relief Procedure for turning off the unit. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not kink or over-bend the hose. • Do not expose the hose to temperatures or to pressures in excess of those specified by Graco. • Do not use the hose as a strength member to pull or lift the equipment. • Do not spray with a hose shorter than 25 feet. • Do not alter or modify equipment. Alterations or modifications may void agency approvals and create safety hazards. • Make sure all equipment is rated and approved for the environment in which you are using it. ELECTRIC SHOCK HAZARD This equipment must be grounded. Improper grounding, setup, or usage of the system can cause electric shock. • Turn off and disconnect power cord before servicing equipment. • Connect only to grounded electrical outlets. • Use only 3-wire extension cords. • Ensure ground prongs are intact on power and extension cords. • Do not expose to rain. Store indoors. • Wait five minutes after disconnecting power cord before servicing large capacitor units. PRESSURIZED ALUMINUM PARTS HAZARD Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or property damage. • Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents. • Many other fluids may contain chemicals that can react with aluminum. Contact your material supplier for compatibility. MOVING PARTS HAZARD Moving parts can pinch, cut or amputate fingers and other body parts. • Keep clear of moving parts. • Do not operate equipment with protective guards or covers removed. • Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure and disconnect all power sources. PERSONAL PROTECTIVE EQUIPMENT Wear appropriate protective equipment when in the work area to help prevent serious injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective equipment includes but is not limited to: • Protective eyewear, and hearing protection. • Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.
Page 8 of the Graco Ultra Max II 1095 user manual — Component Identification
Page 8 · click to enlarge
Page 8
Component Identification Component Identification 695 / 795 / 1095 / 1595 / Mark IV / Mark V / Mark VII / Mark X Standard Models: A M B L C OFF ON D ti14839c G H J K E F A Pressure Gauge (not available on all units) G Filter B Amp Switch (not available on all units) H Strainer C ON/OFF Switch J Pump D Pressure Control K Drain Tube E Prime / Spray Valve L Model/Serial Tag F Trigger Lock M ProGuard Status Light APressure Gauge (not available on all units BAmp Switch (not available on all units) CON/OFF Switch DPressure Control EPrime / Spray Valve FTrigger Lock
Graco Ultra Max II 1095 — Component Identification diagram (page 8)
Fig. 3 · Component Identification
Page 9 of the Graco Ultra Max II 1095 user manual — Component Identification
Page 9 · click to enlarge
Page 9
695 / 795 / 1095 / 1595 Mark IV / Mark V / Mark VII / Mark X ProContractor Models: A R P B C N OFF ON M D L K E G H J F F ti18239b A Smart Control 3.0 Display J Pump B Amp Switch (not available on all units) K ProConnect™ II C ON/OFF Switch L Tool Box D Pressure Control M Rod Pull Feature E Spray / Prime / Fast Flush N Unit / Serial Tag F Trigger Lock P Drain Tube G Filter R QuikReel H Strainer ASmart Control 3.0 Display BAmp Switch (not available on all units) CON/OFF Switch DPressure Control ESpray / Prime / Fast Flush FTrigger Lock GFilter HStrainer
Graco Ultra Max II 1095 — Component Identification diagram (page 9)
Fig. 4 · Component Identification
Page 10 of the Graco Ultra Max II 1095 user manual — Component Identification
Page 10 · click to enlarge
Page 10
1095 / 1595 / Mark V IronMan Models: A N B C OFF ON M D L K E G H J F ti22935a A Smart Control 3.0 Display H Strainer B Amp Switch (not available on all units) J Pump C ON/OFF Switch K ProConnect™ II D Pressure Control L Rod Pull Feature E Spray / Prime / Fast Flush M Unit / Serial Tag F Trigger Lock N Drain Tube G Filter ASmart Control 3.0 Display BAmp Switch (not available on all units) CON/OFF Switch DPressure Control ESpray / Prime / Fast Flush FTrigger Lock GFilter
Graco Ultra Max II 1095 — Component Identification diagram (page 10)
Fig. 5 · Component Identification

Component Identification

Page 11 of the Graco Ultra Max II 1095 user manual — Extension Cords
Page 11 · click to enlarge
Page 11

Grounding

Do not modify plug! If it will not fit in outlet, have grounded outlet installed by a qualified electrician. Do not use an adapter.

Graco Ultra Max II 1095 — Grounding diagram (page 11)
Fig. 6 · Grounding

The equipment must be grounded to reduce the risk of static sparking and electric shock. Electric or static sparking can cause fumes to ignite or explode. Improper grounding can cause electric shock. Grounding provides an escape wire for the electric current.

Power Requirements

  • 100-120V units require 100-120 VAC, 50/60 Hz, 15A, 1 phase
  • 230V units require 220-240 VAC, 50/60 Hz, 10A-16A

The sprayer cord includes a grounding wire with an appropriate grounding contact. Do not use the sprayer if the electrical cord has a damaged ground contact.

Extension Cords

Use an extension cord with an undamaged ground contact.

If an extension cord is necessary, use a 3-wire, 12 AWG (2.5 mm2) minimum. Longer cords and higher gauge cords reduce sprayer performance.

The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Graco Ultra Max II 1095 — Extension Cords diagram (page 11)
Fig. 7 · Extension Cords

Grounding

Page 12 of the Graco Ultra Max II 1095 user manual — 10/16 Amp Switch
Page 12 · click to enlarge
Page 12
Graco Ultra Max II 1095 — 10/16 Amp Switch diagram (page 12)
Fig. 8 · 10/16 Amp Switch

Solvent and oil/based fluids: follow local code. Use only conductive metal pails, placed on a grounded sur- face such as concrete.

Do not place pail on a nonconductive surface such as paper or cardboard which interrupts grounding continuity.

Select 10A or 16A setting based on your circuit rating.

Grounding a metal pail: connect a ground wire to the pail by clamping one end to pail and other end to a true earth ground.

Select 15A or 20A setting based on your circuit rating.

To maintain grounding continuity when flushing or relieving pressure: hold metal part of spray gun firmly to side of a grounded metal pail. Then trigger gun.

10/16 Amp Switch

Page 13 of the Graco Ultra Max II 1095 user manual — Pressure Relief Procedure
Page 13 · click to enlarge
Page 13

Pressure Relief Procedure

Follow the Pressure Relief Procedure whenever you see this symbol.

4. Turn pressure to lowest setting. Trigger gun to relieve pressure.

This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment.

1. Turn power OFF. Wait 7 seconds for power to dissipate.
5. Put drain tube in pail. Turn prime valve down to DRAIN position. Leave prime valve in DRAIN position until you are ready to spray again.
2. Engage trigger lock.
6. If you suspect the spray tip or hose is clogged or that pressure has not been fully relieved after following the steps above, VERY SLOWLY loosen tip guard retaining nut or hose end coupling to relieve pressure gradually, then loosen completely. Clear hose or tip obstruction.
3. Remove guard and SwitchTip.

Pressure Relief Procedure

Page 14 of the Graco Ultra Max II 1095 user manual — Setup
Page 14 · click to enlarge
Page 14

Setup

5. Check inlet strainer for clogs and debris.
1. All sprayers except ProContractor: Connect Graco airless hose to sprayer. Tighten securely.
6. Fill throat packing nut with Graco TSL to prevent premature packing wear. Do this each time you spray.

If using the optional hopper, remove the nipple fit- ting from the filter. Install 45° elbow (from parts box) into filter and install nipple fitting into elbow. Then connect the hose to the nipple.

7. Turn power OFF.
8. Plug power supply cord into a properly grounded electrical outlet.
2. Connect whip hose (if applicable) and gun to other end of hose. Tighten securely.
9. Turn prime valve down to DRAIN position.
3. Engage trigger lock.
10. Place pump in grounded metal pail partially filled with flushing fluid. Attach ground wire to pail and to true earth ground. Perform steps 1 - 5 of Startup to flush out storage oil shipped in sprayer. Use water to flush water-base paint and mineral spirits to flush oil-base paint and storage oil.
4. Remove tip guard.
Show 4 more labels / short text on this page
Setup · ti17608b · ti18421b · ti18245b
Page 15 of the Graco Ultra Max II 1095 user manual — Startup
Page 15 · click to enlarge
Page 15

Startup

6. Hold gun against grounded metal flushing pail. Trigger gun and increase fluid pressure 1/2 turn. Flush 1 minute.
Graco Ultra Max II 1095 — Startup diagram (page 15)
Fig. 9 · Startup
1. Perform Pressure Relief Procedure , page 13.
Graco Ultra Max II 1095 — Startup diagram (page 15)
Fig. 10 · Startup

High-pressure spray is able to inject toxins into the body and cause serious bodily injury. Do not stop leaks with hand or rag.

7. Inspect for leaks. If leaks occur, perform Pressure Relief Procedure , page 13. Tighten fittings. Perform Startup , steps 1 - 5. If no leaks, proceed to step 7.
8. Place pump in paint pail.
4. Increase pressure 1/2 turn to start motor and allow fluid to circulate through drain tube for 15 seconds; turn pressure down.
Graco Ultra Max II 1095 — Startup diagram (page 15)
Fig. 11 · Startup
9. Trigger gun again into flushing pail until paint appears. Move gun to paint pail and trigger for 20 seconds.
5. Turn prime valve forward to SPRAY position. Disengage trigger lock.
10. Engage trigger lock. Assemble tip and guard, see instructions on next page.

Startup

Page 16 of the Graco Ultra Max II 1095 user manual — Clearing Tip Clog
Page 16 · click to enlarge
Page 16

Switch Tip Installation

Spray

1. Spray test pattern. Increase pressure to eliminate heavy edges. Use smaller tip size if pressure adjustment can not eliminate heavy edges.
1. Perform Pressure Relief Procedure , page 13.
2. Use spray tip (A) to insert OneSeal ™ (B) into guard (C).

A B

2. Hold gun perpendicular, 10-12 in. (25-30 cm) from surface. Spray back and forth. Overlap by 50%. Trigger gun after moving and release before stopping.
3. Insert Switch Tip.
4. Screw assembly onto gun. Tighten.

Clearing Tip Clog

Graco Ultra Max II 1095 — Clearing Tip Clog diagram (page 16)
Fig. 12 · Clearing Tip Clog

SKIN INJECTION HAZARD Never point gun at your hand or into a rag!

1. Release trigger, engage trigger lock. Rotate SwitchTip. Disengage trigger lock. Trigger gun to clear clog.
2. Engage trigger lock. Return SwitchTip to original position. Disengage trigger lock and continue spraying.

Switch Tip Installation

Page 17 of the Graco Ultra Max II 1095 user manual — (ProContractor and IronMan models only)
Page 17 · click to enlarge
Page 17

Fast Flush (ProContractor and IronMan models only)

Fast Flush

WatchDog ™ Protection System (ProContractor and IronMan models only)

(ProContractor and IronMan models only)

To flush the hose and gun at an accelerated speed, per- form the following steps:

Pump stops automatically when material pail is empty.

Graco Ultra Max II 1095 — (ProContractor and IronMan models only) diagram (page 17)
Fig. 13 · (ProContractor and IronMan models only)

To Activate:

1. Perform steps 1 - 3 of Cleanup , page 22.
1. Perform Startup .
Graco Ultra Max II 1095 — (ProContractor and IronMan models only) diagram (page 17)
Fig. 14 · (ProContractor and IronMan models only)
2. Squeeze gun trigger and turn prime valve down to DRAIN position and then over to FAST FLUSH.
2. Turn WatchDog switch ON and WD ON displays. EMPTY displays/flashes and pump stops when Watchdog protection system detects an empty material pail.
3. Turn WatchDog switch OFF. Add material or reprime sprayer. Turn pump switch OFF and ON to reset WatchDog protection system. Turn WatchDog switch back ON to continue to monitor material level.
Graco Ultra Max II 1095 — (ProContractor and IronMan models only) diagram (page 17)
Fig. 15 · (ProContractor and IronMan models only)
Page 18 of the Graco Ultra Max II 1095 user manual — Standard Models
Page 18 · click to enlarge
Page 18

ProGuard

This sprayer protects itself against high and low voltage. If the sprayer is plugged into a power source that is too low or too high the sprayer will stop operating.

ProContractor and IronMan Models

One of three error codes will be displayed:

Standard Models

Standard models come equipped with a ProGuard sta- tus indicator light. This light has three different states of operation: ON, blink, and OFF.

Multiple incoming voltage surges detected - unplug sprayer and locate good voltage supply to prevent damage to electronics. Typical cause of this error is plugging into a circuit that is higher than the rated voltage of the sprayer. Find a circuit that supplies the correct voltage.

Graco Ultra Max II 1095 — Standard Models diagram (page 18)
Fig. 16 · Standard Models

Light is ON Unit is powered and operating normally.

Incoming voltage too low for sprayer operation - unplug sprayer and locate good voltage supply to prevent damage to electronics. Typical cause of this error is other equipment on the same circuit or generator frequently turning on/off under load. Find a circuit that is dedicated to the sprayer.

Light is Blinking Voltage supply is too low or too high for sprayer and will not run until it is plugged into a good power supply.

Light is OFF No power to sprayer, or there is another error other than the voltage supply.

Sprayer plugged into wrong voltage - unplug sprayer and locate correct voltage supply. Typical cause of this error is a GFCI box that is wired for the wrong voltage (240V vs. 120V). No damage has occurred to the sprayer. Find a circuit with the correct voltage and the sprayer will run correctly.

See Troubleshooting (page 24) to determine the cause of any errors.

Graco Ultra Max II 1095 — Standard Models diagram (page 18)
Fig. 17 · Standard Models

ProGuard · Error Code Definition

Page 19 of the Graco Ultra Max II 1095 user manual — Hose Reel
Page 19 · click to enlarge
Page 19

Hose Reel

Graco Ultra Max II 1095 — Hose Reel diagram (page 19)
Fig. 18 · Hose Reel
3. Pull reel handle up and turn clockwise to reel in hose.

Moving parts can pinch, cut or amputate fingers and other body parts. To avoid injury from moving parts, be sure to keep your head clear of hose reel while winding up hose.

1. Make sure hose is routed through hose guide.
2. Lift and turn pivot lock 90° to unlock hose reel. Pull on hose to remove it from hose reel.

Hose Reel

Page 20 of the Graco Ultra Max II 1095 user manual — Change Display Units
Page 20 · click to enlarge
Page 20

Digital Tracking System (ProContractor and IronMan models only)

Digital Tracking System

Job Gallons

(ProContractor and IronMan models only)

1. Short press DTS button to move to Job Gallons (or liters x 10).

Operation Main Menu

Graco Ultra Max II 1095 — Operation Main Menu diagram (page 20)
Fig. 19 · Operation Main Menu

Short press to move to next display. Press and hold (5 seconds) to change units or reset data.

1. Turn pressure to lowest setting. Trigger gun to relieve pressure. Turn prime valve down to DRAIN position.
2. Press and hold to reset to zero.
Graco Ultra Max II 1095 — Operation Main Menu diagram (page 20)
Fig. 20 · Operation Main Menu

Lifetime Gallons

1. Short press DTS button to move to Lifetime Gallons (or liters x 10).
2. Turn power ON. Pressure display appears. Dashes will not appear unless pressure is less than 200 psi (14 bar, 1,4 MPa).
Graco Ultra Max II 1095 — Lifetime Gallons diagram (page 20)
Fig. 21 · Lifetime Gallons
Graco Ultra Max II 1095 — Lifetime Gallons diagram (page 20)
Fig. 22 · Lifetime Gallons

Change Display Units

Press and hold DTS button for 5 seconds to change pressure units (psi, bar, MPa) to desired units. Selec- tion of bar or MPa changes gallons to liters x 10. To change display units DTS must be in pressure display mode and pressure must be at zero.

Graco Ultra Max II 1095 — Change Display Units diagram (page 20)
Fig. 23 · Change Display Units
Page 21 of the Graco Ultra Max II 1095 user manual — Secondary Menu - Stored Data
Page 21 · click to enlarge
Page 21

Digital Tracking System (ProContractor and IronMan models only)

Secondary Menu - Stored Data

7. Short press DTS button. W-DOG scrolls past then OFF displays if watchdog switch is OFF. ON displays if Watchdog switch is ON.
1. Perform Pressure Relief, steps 1 - 4 if they have not already been done.
Graco Ultra Max II 1095 — Secondary Menu - Stored Data diagram (page 21)
Fig. 24 · Secondary Menu - Stored Data
2. Turn power switch on while holding DTS button down.
8. Press and hold (8 seconds) DTS button to move to WatchDog Trigger % menu. Continue to hold DTS button and Watchdog can be set to trigger at 30, 40, 50, or 60% of current sprayer pressure setting. Release DTS button when desired % is displayed. Default is 50%.
3. SERIAL NUMBER scrolls past and then serial number (e.g. 00001) displays.
4. Short press DTS button and MOTOR HOURS scrolls past and then total motor run hours are displayed.
9. Short press to move to SOFTWARE REV .
10. Short press DTS button. MOTOR ID RESISTOR scrolls by and model code number (see below).
5. Short press DTS button. LAST CODE scrolls by and last code is displayed; e.g. E=07 (see Repair manual).
Graco Ultra Max II 1095 — Secondary Menu - Stored Data diagram (page 21)
Fig. 25 · Secondary Menu - Stored Data
Graco Ultra Max II 1095 — Secondary Menu - Stored Data diagram (page 21)
Fig. 26 · Secondary Menu - Stored Data

0 695 2 795 / Mark IV 4 1095 / 230V Mark V 6 1595 / 120V Mark V / MARK VII 10 Mark X

6. Press and hold DTS button to clear code to zero.
Page 22 of the Graco Ultra Max II 1095 user manual — Cleanup
Page 22 · click to enlarge
Page 22

Cleanup

5. Turn prime valve down to DRAIN position and allow flushing fluid to circulate until flushing fluid appears clear.
1. Perform Pressure Relief Procedure (page 13), steps 1 - 4. Remove tip guard from gun.
Graco Ultra Max II 1095 — Cleanup diagram (page 22)
Fig. 27 · Cleanup
6. Turn prime valve forward to SPRAY position. Trigger gun into flushing pail to purge fluid from hose.
2. Turn power ON . Turn prime valve forward to SPRAY position.
Graco Ultra Max II 1095 — Cleanup diagram (page 22)
Fig. 28 · Cleanup
3. Increase pressure to 1/2. Hold gun against pail. Disengage trigger lock. Trigger gun until flushing fluid appears.
7. Raise pump above flushing fluid and run sprayer for 15 to 30 seconds to drain fluid. Turn power OFF.
4. Move gun to waste pail, hold gun against pail, trigger gun to thoroughly flush system. Release trigger and engage trigger lock.
Graco Ultra Max II 1095 — Cleanup diagram (page 22)
Fig. 29 · Cleanup
8. Turn prime valve down DRAIN position. Unplug sprayer.

Cleanup · ti18249a ti22944a

Page 23 of the Graco Ultra Max II 1095 user manual — Cleanup
Page 23 · click to enlarge
Page 23
9. Remove filters from gun and sprayer, if installed. Clean and inspect. Install filters.
Graco Ultra Max II 1095 — Cleanup diagram (page 23)
Fig. 30 · Cleanup
11. Wipe sprayer, hose and gun with a rag soaked in water or mineral spirits.
Graco Ultra Max II 1095 — Cleanup diagram (page 23)
Fig. 31 · Cleanup
10. If flushing with water, flush again with mineral spirits, or Pump Armor, to leave a protective coating to prevent freezing or corrosion.

Cleanup · Pump Armor

Page 24 of the Graco Ultra Max II 1095 user manual — TYPE OF PROBLEM
Page 24 · click to enlarge
Page 24

Troubleshooting

Mechanical/Fluid Flow

Perform Pressure Relief Procedure; page 13.

WHAT TO CHECK If check is OK, go to next check

WHAT TO DO When check is not OK, refer to this column

TYPE OF PROBLEM

For units with display: CODE XX is displayed.

Fault condition exists Determine fault correction from table, page 27.

For units with no display: ProGuard status light is blinking or the light is off and there is power to the sprayer.

Pump output is low Spray tip worn Follow Pressure Relief Procedure on page 13, then replace tip. See your separate gun or tip manual.

Spray tip clogged Relieve pressure. Check and clean spray tip.

Paint supply Refill and reprime pump.

Intake strainer clogged Remove and clean, then reinstall

Intake valve ball and piston ball are not seating properly

Remove intake valve and clean. Check balls and seats for nicks; replace if necessary; see pump manual. Strain paint before using to remove particles that could clog pump.

Fluid filter, tip filter, or tip is clogged or dirty.

Clean filter; see operation manual.

Prime valve leaking Relieve pressure. Repair prime valve.

Verify pump does not continue to stroke when gun trigger is released. (Prime valve not leaking.)

Service pump; see pump manual.

Leaking around throat packing nut which may indicate worn or damaged packings.

Replace packings; see pump manual. Also check piston valve seat for hardened paint or nicks and replace if necessary. Tighten pack- ing nut/wet-cup.

Troubleshooting

Page 25 of the Graco Ultra Max II 1095 user manual — TYPE OF PROBLEM
Page 25 · click to enlarge
Page 25

WHAT TO CHECK If check is OK, go to next check

WHAT TO DO When check is not OK, refer to this column

TYPE OF PROBLEM

Pump output is low Pump rod damage Repair pump. See pump manual.

Low stall pressure Turn pressure knob fully clockwise. Make sure pressure control knob is properly installed to allow full clockwise position. If problem per- sists, replace pressure transducer.

Piston packings are worn or dam- aged

Replace packings; see pump manual.

O-ring in pump is worn or damaged Replace o-ring; see pump manual.

Intake valve ball is packed with mate- rial

Clean intake valve; see pump manual.

Pressure setting is too low Increase pressure; see pump manual.

Large pressure drop in hose with heavy materials

Use larger diameter hose and/or reduce overall length of hose.

Check to see if Amp switch (10/16 or 15/20) is on low setting. Make sure circuit is able to provide high setting.

Switch to 16A or 20A setting. Change to circuit that provides 16A or 20A. Change to less loaded circuit.

Motor runs but pump does not stroke

Displacement pump pin damaged or missing; see pump manual.

Replace pump pin if missing. Be sure retainer spring is fully in groove all around connecting rod; see pump manual.

Connecting rod assembly damaged; see pump manual.

Replace connecting rod assembly; see pump manual.

Gears or drive housing damaged. Inspect drive housing assembly and gears for damage and replace if necessary; see pump manual.

Excessive paint leakage into throat packing nut

Throat packing nut is loose Remove throat packing nut spacer. Tighten throat packing nut just enough to stop leakage.

Throat packings are worn or dam- aged

Replace packings; see pump manual.

Displacement rod is worn or dam- aged

Replace rod; see pump manual.

Fluid is spitting from gun Air in pump or hose Check and tighten all fluid connections. Cycle pump as slowly as possible during priming.

Fluid supply is low or empty Refill fluid supply. Prime pump; see pump man- ual. Check fluid supply often to prevent running pump dry.

Troubleshooting

Page 26 of the Graco Ultra Max II 1095 user manual — TYPE OF PROBLEM
Page 26 · click to enlarge
Page 26

WHAT TO CHECK If check is OK, go to next check

WHAT TO DO When check is not OK, refer to this column

TYPE OF PROBLEM

Pump is difficult to prime Air in pump or hose Check and tighten all fluid connections. Cycle pump as slowly as possible during priming.

Intake valve is leaking Clean intake valve. Be sure ball seat is not nicked or worn and that ball seats well. Reas- semble valve.

Pump packings are worn Replace pump packings; see pump manual.

Paint is too thick Thin the paint according to supplier recommen- dations.

No display, sprayer operates

Display is damaged or has bad con- nection

Check connections. Replace display.

Troubleshooting

Page 27 of the Graco Ultra Max II 1095 user manual — Electrical
Page 27 · click to enlarge
Page 27

Electrical

ProGuard Status Light Control Board Status Light

Symptom: Sprayer does not run, stops running, or will not shut off.

Graco Ultra Max II 1095 — Electrical diagram (page 27)
Fig. 32 · Electrical

Perform Pressure Relief Procedure; page 13.

1. Plug sprayer into correct voltage, grounded outlet.

For units without a display, see ProGuard (page 18). If there is a voltage supply issue (CODE 04, 08, or 17), the ProGuard status light will blink continuously when the ON/OFF switch is ON. To determine which code (or any other code besides voltage supply) refer to the control board status light. Turn the ON/OFF switch OFF, remove the control cover then turn power back ON. Observe the status light. Blinking LED total count equals the error code (for example: two blinks equals CODE 02).

2. Set power switch OFF for 30 seconds and then ON again (this ensures sprayer is in normal run mode).
3. Turn pressure control knob clockwise 1/2 turn.
4. View digital displayy.

Keep clear of electrical and moving parts during trou- bleshooting procedures. To avoid electrical shock haz- ards when covers are removed for troubleshooting, wait 5 minutes after unplugging power cord for stored elec- tricity to dissipate.

TYPE OF PROBLEM WHAT TO CHECK HOW TO CHECK

Sprayer does not run at all See flow chart, page 33.

ProGuard status light and control board status light never light

Sprayer does not run at all Check transducer or transducer connections

1. Make sure there is no pressure in the system (see Pressure Relief Procedure , page 13 ). Check fluid path for clogs, such as clogged filter.

Display shows CODE 02

2. Use airless paint spray hose with no metal braid 1/4 in. x 50 ft minimum. Smaller hose or metal braid hose may result in high-pressure spikes.
3. Set sprayer to OFF and disconnect power to sprayer.
4. Check transducer and connections to control board.
5. Disconnect transducer from control board socket. Check that transducer and control board contacts are clean and secure.

Control board status light blinks 2 times repeatedly

6. Reconnect transducer to control board socket. Connect power, set sprayer ON and control knob 1/2 turn clockwise. If sprayer does not run properly, set sprayer to OFF and go to next step.
7. Install new transducer. Connect power, set sprayer ON and control knob 1/2 turn clockwise. Replace control board if sprayer does not run properly.

Troubleshooting · Display is blank

Page 28 of the Graco Ultra Max II 1095 user manual — Troubleshooting
Page 28 · click to enlarge
Page 28

TYPE OF PROBLEM WHAT TO CHECK HOW TO CHECK

Sprayer does not run at all Check transducer or transducer connections (control board is not detecting a pressure signal).

1. Set sprayer to OFF and disconnect power to sprayer.

Display shows CODE 03

2. Check transducer and connections to control board.
3. Disconnect transducer from control board socket. Check to see if transducer and control board contacts are clean and secure.
4. Reconnect transducer to control board socket. Connect power, set sprayer ON and control knob to 1/2 turn clockwise. If sprayer does not run, set sprayer to OFF and go to next step.

Control board status light blinks 3 times repeatedly

5. Connect a confirmed working transducer to control board socket.
6. Set sprayer ON and control knob to 1/2 turn clockwise. If sprayer runs, install new transducer. Replace control board if sprayer does not run.
7. Check transducer resistance with ohmmeter (less than 9k ohm between red and black wires and 3-6k ohm between green and yellow wires).

Sprayer does not run at all Check voltage supply to the sprayer (control board is detecting a multiple voltage surges).

1. Set sprayer to OFF and disconnect power to sprayer.

Display shows CODE 4

2. Locate a good voltage supply to prevent damage to electronics.

Control board status light blinks four times repeatedly

Troubleshooting

Page 29 of the Graco Ultra Max II 1095 user manual — STEP 3:
Page 29 · click to enlarge
Page 29

TYPE OF PROBLEM WHAT TO CHECK HOW TO CHECK

Sprayer does not run at all Control is commanding motor to run but motor shaft does not rotate. Possibly locked rotor condition, an open connection exists between motor and control, there is a problem with motor or control board, or motor amp draw is excessive.

1. Remove pump and try to run sprayer. If motor runs, check for locked or frozen pump or drive train. If sprayer does not run, continue to step 2.

Display shows CODE 05

2. Set sprayer to OFF and disconnect power to sprayer.
3. Disconnect motor connector(s) from control board socket(s). Check that motor connector and control board contacts are clean and secure. If contacts are clean and secure, continue to step 4.

Control board status light blinks 5 times repeatedly

4. Set sprayer to OFF and spin motor fan 1/2 turn. Restart sprayer. If sprayer runs, replace control board. If sprayer does not run, continue to step 5.

5. Perform Spin Test: Test at large 4-pin motor field connector. Disconnect fluid pump from sprayer. Test motor by placing a jumper across pins 1 & 2. Rotate motor fan at about 2 revolutions per second. A cogging resistance to motion should be felt at the fan. The motor should be replaced if no resistance is felt. Repeat for pin combinations 1 & 3 and 2 & 3. Pin 4 (the green wire) is not used in this test. If all spin test is positive, continue to step 6.

Green Blue Red Black

STEP 1:

Green Blue Red Black

STEP 2:

Green Blue Red Black

STEP 3:

Troubleshooting

Page 30 of the Graco Ultra Max II 1095 user manual — Troubleshooting
Page 30 · click to enlarge
Page 30

TYPE OF PROBLEM WHAT TO CHECK HOW TO CHECK

Sprayer does not run at all Control is commanding motor to run but motor shaft does not rotate. Possibly locked rotor condition, an open connection exists between motor and control, there is a problem with motor or control board, or motor amp draw is excessive.

6. Perform Field Short Test: Test at large 4-pin motor field connector. There should not be continuity from pin 4, the ground wire, and any of the remaining 3 pins. If motor field connector tests fail, replace motor.

Display shows CODE 05

7. Check Motor Thermal Switch: Unplug thermal wires. Set meter to ohms. Meter should read the proper resistance for each unit (see table below).

Control board status light blinks 5 times repeatedly

Resistance Table:

695/240V Mark IV 0 ohms

795/120V Mark IV 2k ohms

1095/240V Mark V 3.9k ohms

1595/120V Mark V/MARK VII 6.2k ohms

MARK X 10.0k ohms

Troubleshooting

Page 31 of the Graco Ultra Max II 1095 user manual — Troubleshooting
Page 31 · click to enlarge
Page 31

TYPE OF PROBLEM WHAT TO CHECK HOW TO CHECK

Sprayer does not run at all Allow sprayer to cool. If sprayer runs when cool, correct cause of overheating. Keep sprayer in cooler location with good ventilation. Make sure motor air intake is not blocked. If sprayer still does not run, follow Step 1.

Display shows CODE 06

1. Check thermal device connector (yellow wires) at control board.
2. Disconnect thermal device connector from control board socket. Make sure contacts are clean and secure. Measure resistance of the thermal device. If reading is not correct, replace motor.

Check Motor Thermal Switch: Unplug thermal wires. Set meter to ohms. Meter should read the proper resistance for each unit (see table below).

Control board status light blinks 6 times repeatedly

Resistance Table:

695/240V Mark IV 0 ohms

795/120V Mark IV 2k ohms

1095/240V Mark V 3.9k ohms

1595/120V Mark V/MARK VII 6.2k ohms

MARK X 10.0k ohms

3. Reconnect thermal device connector to control board socket. Connect power, turn sprayer ON and control knob 1/2 turn clockwise. If sprayer does not run, replace control board.

Sprayer does not run at all Check voltage supply to the sprayer (incoming voltage too low for sprayer operation)

1. Set sprayer to OFF and disconnect power to sprayer.

Display shows CODE 08

2. Remove other equipment that uses the same circuit.
3. Locate a good voltage supply to avoid damage to electronics.

Control board status light blinks eight times repeatedly

Sprayer does not run at all Check to see if control board is over heating.

1. Make sure motor air intake is not blocked.

Display shows CODE 10

2. Make sure fan has not failed.
3. Make sure control board is properly connected to back plate and that conductive thermal paste is used on power components.
4. Replace control board.
5. Replace motor.

Control board status light blinks 10 times repeatedly

Troubleshooting

Page 32 of the Graco Ultra Max II 1095 user manual — Troubleshooting
Page 32 · click to enlarge
Page 32
Graco Ultra Max II 1095 — Troubleshooting diagram (page 32)
Fig. 33 · Troubleshooting

TYPE OF PROBLEM WHAT TO CHECK HOW TO CHECK

Sprayer does not run at all Excessive current protection enabled

Sprayer does not run at all Check the connections above the motor

1. Set sprayer to OFF and disconnect power to sprayer.
3. Disconnect motor control and inspect for damage at connectors.
5. Turn power on. If code continues, replace motor.

Sprayer does not run at all Check the connections. Control is not receiving a motor position sensor signal

2. Disconnect motor position sensor and inspect for damage at connectors.
4. Turn power ON. If code continues, replace motor.

Sprayer does not run at all Check voltage supply to the sprayer (sprayer plugged into wrong voltage)

1. Set sprayer to OFF and disconnect power to sprayer.
2. Locate a good voltage supply to avoid damage to electronics.

Troubleshooting

Page 33 of the Graco Ultra Max II 1095 user manual — Troubleshooting
Page 33 · click to enlarge
Page 33

Sprayer Will Not Run (See following page for steps)

Graco Ultra Max II 1095 — Troubleshooting diagram (page 33)
Fig. 34 · Troubleshooting

Remove control box cover. Turn sprayer ON. Observe control board status light on control board (see page 27).

retest. If Step 3 still shows incorrect resistance, replace

Troubleshooting

Page 34 of the Graco Ultra Max II 1095 user manual — Troubleshooting
Page 34 · click to enlarge
Page 34
Graco Ultra Max II 1095 — Troubleshooting diagram (page 34)
Fig. 35 · Troubleshooting
1. Plug power cord in and turn switch ON. Connect probes to on/off switch. Turn meter to AC Volts.
2. Plug power cord in and turn switch ON. Connect probes to on/off switch. Turn meter to AC Volts.
3. Check motor thermal switch. Unplug yellow wires. Meter should read according to Resistance Table on page 30. NOTE: Motor should be cool during reading.
4. Plug power cord in and turn switch ON. Disconnect potentiometer.

Troubleshooting

Page 35 of the Graco Ultra Max II 1095 user manual — YES
Page 35 · click to enlarge
Page 35

Sprayer Will Not Shut Off

1. Perform Pressure Relief Procedure ; page 13. Leave prime valve open and power switch OFF.
2. Remove control box cover so the control board status light can be viewed if available.

Plumb pressure gauge into paint hose, plug sprayer in, and turn power

Mechanical problemSee the proper fluid pump manual for the sprayer for

NO

switch ON. Does sprayer reach or

further trouble shooting procedures.

exceed its maximum pressure?

YES

Unplug the transducer from control

NO

Replace the control board.

board. Does motor stop running?

YES

Bad transducer. Replace and test

with a new one.

Troubleshooting · Troubleshooting Procedure

Page 36 of the Graco Ultra Max II 1095 user manual — Technical Data
Page 36 · click to enlarge
Page 36

Technical Data

695 Sprayers U.S. Metric

North American Models 0.95 gpm 3.6 lpm International Models 0.75 gpm 2.8 lpm Maximum Tip Size 0.031 0.031 Fluid Outlet npsm 1/4 in. 1/4 in. Cycles 226 per gallon 60 per liter Generator Minimum 5000 W 5000 W 120V, A, Hz 14.8, 50/60 14.8, 8, 50/60 230V, A, Hz 9, 50/60 9, 50/60 Dimensions

Weight:

Standard Series Lo-Boy 94 lb 43 kg Standard Series Hi-Boy 94 lb 43 kg ProContractor 111 lb 50 kg Height:

Standard Series Lo-Boy 27.5 in. 69.9 cm

Standard Series Hi-Boy 28.5 in. (Handle down) 38.75 in. (Handle up) 72.4 cm (Handle down) 98.4 cm (Handle up) ProContractor 39 in. 99 cm Length:

Standard Series Lo-Boy 37 in. 94 cm Standard Series Hi-Boy 26 in. 66 cm ProContractor 29.5 in. 75 cm Width: 22.5 in. 57.2 cm

Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,

leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass Noise Level:

Sound Power 91 dBa* 91 dBa* Sound Pressure 82 dBa* 82 dBa* *per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m

Technical Data · Sprayer · Maximum Delivery

Page 37 of the Graco Ultra Max II 1095 user manual — 795 Sprayers U.S. Metric
Page 37 · click to enlarge
Page 37

795 Sprayers U.S. Metric

North American Models 1.1 gpm 4.2 lpm International Models 0.95 gpm 3.6 lpm Maximum Tip Size 0.033 0.033 Fluid Outlet npsm 1/4 in. 1/4 in. Cycles 195 per gallon 52 per liter Generator Minimum 5000 W 5000 W 120V, A, Hz 15, 50/60 15, 50/60 230V, A, Hz 10, 50/60 10, 50/60 Dimensions

Weight:

Standard Series Lo-Boy 98 lb 45 kg Standard Series Hi-Boy 98 lb 45 kg ProContractor 115 lb 52 kg Height:

Standard Series Lo-Boy 27.5 in. 69.9 cm

Standard Series Hi-Boy 28.5 in. (Handle down) 38.75 in. (Handle up) 72.4 cm (Handle down) 98.4 cm (Handle up) ProContractor 39 in. 99 cm Length:

Standard Series Lo-Boy 37 in. 94 cm Standard Series Hi-Boy 26 in. 66 cm ProContractor 29.5 in. 75 cm Width: 22.5 in. 57.2 cm

Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,

leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass Noise Level:

Sound Power 91 dBa* 91 dBa* Sound Pressure 82 dBa* 82 dBa* *per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m

Technical Data · Sprayer · Maximum Delivery

Page 38 of the Graco Ultra Max II 1095 user manual — 1095 Sprayers U.S. Metric
Page 38 · click to enlarge
Page 38

1095 Sprayers U.S. Metric

North American Models 1.2 gpm 4.5 lpm International Models 1.1 gpm 4.1 lpm Maximum Tip Size 0.035 0.035 Fluid Outlet npsm 1/4 in. 1/4 in. Cycles 123 per gallon 33 per liter Generator Minimum 5000 W 5000 W 120V, A, Hz 15, 50/60 15, 50/60 230V, A, Hz 10, 50/60 10, 50/60 Dimensions

Weight:

Standard Series Hi-Boy 120 lb 55 kg ProContractor 141 lb 64 kg IronMan 127 lb 58 kg Height:

Standard Series Hi-Boy 29.5 in. (Handle down) 38.5 in. (Handle up) 74.9 cm (Handle down) 97.8 cm (Handle up) ProContractor 39 in. 99 cm IronMan 40.2 in. 102 cm Length:

Standard Series Hi-Boy 26 in. 66 cm ProContractor 28 in. 71 cm IronMan 29.9 in. 76 cm Width:

Standard Series Hi-Boy 24 in. 61 cm ProContractor 24 in. 61 cm IronMan 24.4 in. 62 cm

Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,

leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass Noise Level:

Sound Power 91 dBa* 91 dBa* Sound Pressure 82 dBa* 82 dBa* *per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m

Technical Data · Sprayer · Maximum Delivery

Page 39 of the Graco Ultra Max II 1095 user manual — 1595 Sprayers U.S. Metric
Page 39 · click to enlarge
Page 39

1595 Sprayers U.S. Metric

Maximum Delivery 1.35 gpm 5.1 lpm Maximum Tip Size 0.039 0.039 Fluid Outlet npsm 1/4 in. 1/4 in. Cycles 110 per gallon 29 per liter Generator Minimum 5000 W 5000 W 120V, A, Hz 20/15, 50/60 20/15, 50/60 Dimensions

Weight:

Standard Series Hi-Boy 125 lb 57 kg ProContractor 146 lb 66 kg IronMan 132 lb 60 kg Height:

Standard Series Hi-Boy 29.5 in. (Handle down) 38.5 in. (Handle up) 74.9 cm (Handle down) 97.8 cm (Handle up) ProContractor 39 in. 99 cm IronMan 40.2 in. 102 cm Length:

Standard Series Hi-Boy 26 in. 66 cm ProContractor 28 in. 71 cm IronMan 29.9 in. 76 cm Width:

Standard Series Hi-Boy 24 in. 61 cm ProContractor 24 in. 61 cm IronMan 24.4 in. 62 cm

Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,

leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass Noise Level:

Sound Power 91 dBa* 91 dBa* Sound Pressure 82 dBa* 82 dBa* *per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m

Technical Data · Sprayer

Page 40 of the Graco Ultra Max II 1095 user manual — U.S. Metric
Page 40 · click to enlarge
Page 40

Mark IV Sprayers

U.S. Metric

North American Models 1.1 gpm 4.2 lpm International Models 0.95 gpm 3.6 lpm Maximum Tip Size

North American Models 0.033 0.033 International Models 0.031 0.031 Fluid Outlet npsm 3/8 in. 3/8 in. Cycles 195 per gallon 52 per liter Generator Minimum 5000 W 5000 W 120V, A, Hz 15, 50/60 15, 50/60 230V, A, Hz 10, 50/60 10, 50/60 Dimensions

Weight:

Standard Series Hi-Boy 98 lb 45 kg ProContractor 119 lb 54 kg Height:

Standard Series Hi-Boy 28.5 in. (Handle down) 38.75 in. (Handle up) 72.4 cm (Handle down) 98.4 cm (Handle up) ProContractor 39 in. 99 cm Length:

Standard Series Hi-Boy 26 in. 66 cm ProContractor 29.5 in. 75 cm Width: 22.5 in. 57.2 cm

Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,

leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass Noise Level:

Sound Power 91 dBa* 91 dBa* Sound Pressure 82 dBa* 82 dBa* *per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m

Technical Data · Sprayer · Maximum Delivery

Page 41 of the Graco Ultra Max II 1095 user manual — U.S. Metric
Page 41 · click to enlarge
Page 41

Mark V Sprayers

U.S. Metric

North American and UK Models 1.35 gpm 5.1 lpm International Models 1.2 gpm 4.5 lpm Maximum Tip Size

North American and UK Models 0.039 0.039 International Models 0.035 0.035 Fluid Outlet npsm 3/8 in. 3/8 in. Cycles 110 per gallon 29 per liter Generator Minimum 5000 W 5000 W 120V, A, Hz 20/15, 50/60 20/15, 50/60 230V, A, Hz 10, 50/60 10, 50/60 Dimensions

Weight:

Standard Series Hi-Boy 130 lb 59 kg ProContractor 151 lb 68 kg IronMan 137 lb 62 kg Height:

Standard Series Hi-Boy 29.5 in. (Handle down) 38.5 in. (Handle up) 74.9 cm (Handle down) 97.8 cm (Handle up) ProContractor 39 in. 99 cm IronMan 40.2 in. 102 cm Length:

Standard Series Hi-Boy 26 in. 66 cm ProContractor 28 in. 71 cm IronMan 29.9 in. 76 cm Width:

Standard Series Hi-Boy 24 in. 61 cm ProContractor 24 in. 61 cm IronMan 24.4 in. 62 cm

Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,

leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass Noise Level:

Sound Power 91 dBa* 91 dBa* Sound Pressure 82 dBa* 82 dBa* *per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m

Technical Data · Sprayer · Maximum Delivery

Page 42 of the Graco Ultra Max II 1095 user manual — U.S. Metric
Page 42 · click to enlarge
Page 42

Mark VII Sprayers

U.S. Metric

Maximum Delivery 1.58 gpm 6.0 lpm Maximum Tip Size 0.041 in. 0.041 in. Fluid Outlet npsm 1/2 in. 1/2 in. Cycles 97 per gallon 26 per liter Generator Minimum 5000 W 5000 W 230V, A, Hz 16, 50/60 16, 50/60 Dimensions

Weight:

Standard Series Hi-Boy 139 lb 63 kg ProContractor 160 lb 73 kg Height:

Standard Series Hi-Boy 29.5 in. (Handle down) 38.5 in. (Handle up) 74.9 cm (Handle down) 97.8 cm (Handle up) ProContractor 39 in. 99 cm Length:

Standard Series Hi-Boy 26 in. 66 cm ProContractor 28 in. 71 cm Width: 24 in. 61 cm

Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,

leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass Noise Level:

Sound Power 91 dBa* 91 dBa* Sound Pressure 82 dBa* 82 dBa* *per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m

Technical Data · Sprayer

Page 43 of the Graco Ultra Max II 1095 user manual — U.S. Metric
Page 43 · click to enlarge
Page 43

Mark X Sprayers

U.S. Metric

Maximum Delivery 2.1 gpm 8.0 lpm Maximum Tip Size 0.045 in. 0.045 in. Fluid Outlet npsm 1/2 in. 1/2 in. Cycles 70 per gallon 19 per liter Generator Minimum 5000 W 5000 W 230V, A, Hz 16, 50/60 Dimensions

Weight:

Standard Series Hi-Boy 154 lb 70 kg ProContractor 178 lb 81 kg Height:

Standard Series Hi-Boy 29.9 in. (Handle down) 40.1 in. (Handle up) 76 cm (Handle down) 102 cm (Handle up) ProContractor 39 in. 99 cm Length:

Standard Series Hi-Boy 26 in. 66 cm ProContractor 30 in. 75 cm Width: 24 in. 61 cm

Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,

leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass Noise Level:

Sound Power 91 dBa* 91 dBa* Sound Pressure 82 dBa* 82 dBa* *per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m

Technical Data · Sprayer

Page 44 of the Graco Ultra Max II 1095 user manual — Graco Information
Page 44 · click to enlarge
Page 44

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com

For patent information, see www.graco.com/patents

TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 332916

Graco HeadquartersMinneapolis International Offices: Belgium, China, Japan, Korea
  • GRACO INC. AND SUBSIDIARIES
  • P.O. BOX 1441
  • MINNEAPOLIS MN 55440-1441
  • USA

Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com Revision C - March 2014

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
For units with display: CODE XX is displayed. For units with no display: ProGuard status light is blinking or the light is off and there is power to the sprayer.Fault condition exists p.24
Pump output is lowSpray tip worn p.24
Pump output is lowSpray tip clogged p.24
Pump output is lowPaint supply p.24
Pump output is lowIntake strainer clogged p.24
Pump output is lowIntake valve ball and piston ball are not seating properly p.24
Pump output is lowFluid filter, tip filter, or tip is clogged or dirty. p.24
Pump output is lowPrime valve leaking p.24
Pump output is lowVerify pump does not continue to stroke when gun trigger is released. (Prime valve not leaking.) p.24
Pump output is lowLeaking around throat packing nut which may indicate worn or damaged packings. p.24
Pump output is lowPump rod damage p.25
Pump output is lowLow stall pressure p.25
Pump output is lowPiston packings are worn or dam- aged p.25
Pump output is lowO-ring in pump is worn or damaged p.25
Pump output is lowIntake valve ball is packed with mate- rial p.25
Pump output is lowPressure setting is too low p.25
Pump output is lowLarge pressure drop in hose with heavy materials p.25
Pump output is lowCheck to see if Amp switch (10/16 or 15/20) is on low setting. Make sure circuit is able to provide high setting. p.25
Motor runs but pump does not strokeDisplacement pump pin damaged or missing; see pump manual. p.25
Motor runs but pump does not strokeConnecting rod assembly damaged; see pump manual. p.25
Motor runs but pump does not strokeGears or drive housing damaged. p.25
Excessive paint leakage into throat packing nutThroat packing nut is loose p.25
Excessive paint leakage into throat packing nutThroat packings are worn or dam- aged p.25
Excessive paint leakage into throat packing nutDisplacement rod is worn or dam- aged p.25
Fluid is spitting from gunAir in pump or hose p.25
Fluid is spitting from gunTip is partially clogged p.25
Fluid is spitting from gunFluid supply is low or empty p.25
Pump is difficult to primeAir in pump or hose p.26
Pump is difficult to primeIntake valve is leaking p.26
Pump is difficult to primePump packings are worn p.26
Pump is difficult to primePaint is too thick p.26
No display, sprayer operatesDisplay is damaged or has bad con- nection p.26
Sprayer does not run at allSee flow chart, page 33. p.27
Display is blank p.27
ProGuard status light and control board status light never light p.27
Sprayer does not run at allCheck transducer or transducer connections p.27
Display shows CODE 02 p.27
Control board status light blinks 2 times repeatedly p.27
Display shows CODE 03 p.28
Control board status light blinks 3 times repeatedly p.28
Sprayer does not run at allCheck voltage supply to the sprayer (control board is detecting a multiple voltage surges). p.28
Display shows CODE 4 p.28
Control board status light blinks four times repeatedly p.28
Sprayer does not run at allControl is commanding motor to run but motor shaft does not rotate. Possibly locked rotor condition, an open connection exists between motor and control, there is a problem with motor or control board, or motor amp draw is excessive. p.29
Display shows CODE 05 p.29
Control board status light blinks 5 times repeatedly p.29
Sprayer does not run at allAllow sprayer to cool. If sprayer runs when cool, correct cause of overheating. Keep sprayer in cooler location with good ventilation. Make sure motor air intake is not blocked. If sprayer still does not run, follow Step 1. p.31
Display shows CODE 06 p.31
Control board status light blinks 6 times repeatedly p.31
Sprayer does not run at allCheck voltage supply to the sprayer (incoming voltage too low for sprayer operation) p.31
Display shows CODE 08 p.31
Control board status light blinks eight times repeatedly p.31
Sprayer does not run at allCheck to see if control board is over heating. p.31
Display shows CODE 10 p.31
Control board status light blinks 10 times repeatedly p.31
Sprayer does not run at allExcessive current protection enabled p.32
Display shows CODE 12 p.32
Control board status light blinks 12 times repeatedly p.32
Sprayer does not run at allCheck the connections above the motor p.32
Display shows CODE 15 p.32
Control board status light blinks 15 times repeatedly p.32
Sprayer does not run at allCheck the connections. Control is not receiving a motor position sensor signal p.32
Digital display shows CODE 16 p.32
Control board status light blinks 16 times repeatedly p.32
Sprayer does not run at allCheck voltage supply to the sprayer (sprayer plugged into wrong voltage) p.32
Display shows CODE 17 p.32
Control board status light blinks 17 times repeatedly p.32

Ask about the Graco Ultra Max II 1095

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Graco Ultra Max II 1095

Be the first to ask — other owners or our team will answer.

Original document

Graco Ultra Max II 1095 manual PDF

44 pages·6.7 MB·Paint Sprayer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…