Instruction/ maintenance manual of the product MVM96 Goodman Mfg
Go to page of 60
5151 San Felipe Suite 500 Houston, TX 77056 www .goodmanmfg.com • www .amana-hac.com © 2011 Goodman Manufacturing Company , L.P . I NST ALLA TION I NSTRUCTIONS FOR *MVM96 & *CVM96 M ODULA TING .
2 T ABLE OF CONTENTS S HIPPING I NSPECTION ....................................................................................................................................... 6 E LECTROST A TIC D ISCHARGE (ESD) P RECAUTIONS .......................
3 GAS SUPPL Y AND PIPING .......................................................................................................... .................... 29 H IGH A L TITUDE D ERA TE .....................................................................
4 G OOD MA N WILL NOT BE RE SP O N SIB L E FOR ANY INJURY OR PROP E RTY DAMAGE ARISING FROM IMPROPER SERVIC E OR SERVIC E PROC EDU RES .
5 Adhere to the following warnings and cautions when installing, adjusting, altering, servicing, or operating the furnace. T o e nsure proper installation and operation, thoroughly read this manual for specifics pertaining to the installation and application of this product.
6 S HIPPING I NSPECTION All units are securely packed in shipping containers tested ac- cording to International Safe T ransit Association specifications. The carton must be checked upon arrival for external damage. If damage is found, a request for inspection by carrier’s agent must be made in writing immediately .
7 T O PREVEN T PROP ERTY DAMAGE , PER SONAL INJURY OR DEATH DUE TO FIRE , DO NOT INST A LL THI S FUR NAC E IN A MOBILE HOME , TR AI LE R , OR RE CR EAT IO N AL VE HICL E .
8 • All furnace operating conditions (including ignition, input rate, temperature rise and venting) are verified according to these installation instructions. NOTE: The Commonwealth of Massachusetts requires that the following additional requirements must also be met: • Gas furnaces must be installed by a licensed plumber or gas fitter .
9 deicing salts or chemicals carbon tetrachloride halogen type refrigerants cleaning solutions (such as perchloroethylene) printing inks paint removers varnishes hydrochloric acid cements and glues an.
10 C OMBUSTION & V ENTILA TION A IR R EQUIREMENTS T O AVOID PROP E RT Y DAMAGE , PER SONAL INJURY OR DEAT H , SU FFICI ENT FRES H AIR FOR PROP E R CO MB U ST ION AND V ENTILATION OF FLUE GASES MUST BE SUPPL IE D .
11 Horizontal Furnace F URNACE S USPENSION If suspending the furnace from rafters or joists, use 3/8" threaded rod and 2”x2”x1/8” angle iron as shown in the following diagram. The length of rod will depend on the application and the clearances necessary .
12 Recommended Installation Positions NOTE: Alternate “vertical” piping connections can not be used when an upflow furnace is installed with supply air discharging to the right, or when a counterflow furnace is installed with supply air discharging to the left.
13 It is the responsibility of the installer to follow the manufacturers’ recommendations and to verify that all vent/flue piping and connec- tors are compatible with furnace flue products.
14 V ENT /F LUE P IPE V ent/flue pipe can be secured to the vent/flue coupling using the rubber coupling and worm gear hose clamps provided with this furnace (see “S tandard Connections” figure). The rubber coupling allows separation of the vent/flue pipe from the furnace during ser- vicing.
15 N ON -D IRECT V ENT I NSTALLATIONS A minimum of one 90° elbow should be installed on the combus- tion air intake “coupling” to guard against inadvertent blockage.
16 8. Upflow and Counterflow units . For horizontal installations , externally secure the field- supplied vent/flue pipe directly to the vent/flue coupling using a PVC or ABS coupling or elbow .
17 6. For direct vent installations , secure field-supplied combustion air intake pipe directly to the air intake coupling. NOTE: A PVC coupling or elbow is required on counterflow units. N ON -D IRECT V ENT (S INGLE P IPE ) P IPING Non-direct vent installations require only a vent/flue pipe.
18 I n a basement installation, the vent/flue pipe can be run between joist spaces. If the vent pipe must go below a joist and then up into the last joist space to penetrate the header , two 45° elbows should be used to reach the header rather than two 90° elbows.
19 1 234 56 78 2 or 2 1/ 2 4 9 4 6 43 4 0 37 3 4 3 1 28 3 7 1 6 86 56 25 95 6 5 35 0 2 or 2 1/ 2 3 6 3 3 30 2 7 24 2 1 1 8 15 3 5 7 5 45 14 84 54 2 3 93 6 2 or 2 1/ 2 6 1 5 8 55 5 2 49 4 6 4 3 40 3 7 .
20 Alternate Vent Termination Above Anticipated Snow Level (Dual Pipe) In a basement installation, the pipes may be run between the joist spaces. If the pipes must go below the joist and then up into the last joist space to penetrate the header , two 45° elbows should be used to reach the header rather than two 90° elbows.
21 S TANDARD R IGHT OR L EFT S IDE D RAIN H OSE C ONNECTIONS All installations positions require the use of the drain trap, hoses, tubes, and clamps. The following quantity of hoses, tubes, and hose clamps are provided with the unit.
22 A LTERNATE V ENT /F LUE D RAIN H OSE C ONNECTIONS Upright installations using the alternate vent/flue outlet will require “right-side only” drain hoses to be connected as follows. Refer to Vent/Flue Pipe and Combustion Air Pipe for details on alternate vent/flue pipe connection .
23 U PRIGHT I NSTALLATIONS -T RAP ON L EFT S IDE NOTE: For left side trap installation, grommets must be moved to the left side of the furnace and the plugs installed on the right side of the furnace. 1. Remove the rubber plug/cap from the left side drain port on the front cover .
24 H ORIZONTAL I NSTALLATIONS R IGHT S IDE D OWN Horizontal installations with the right side down require that the drain hoses be connected to the right side front cover drain port and the rubber elbow drain port. NOTE: On counterflow models, relocation of the front cover pressure switch hose is required.
25 Horizontal installations with the left side panel down will require drain hoses to be connected to the left side front cover drain port and the side drain port on the rubber elbow . 1 . Remove the rubber plug/cap from the front cover left (down) side drain port.
26 E LECTRICAL C ONNECTIONS HIG H VOLT A G E ! T O AVOID THE RIS K OF ELECT RICAL SHOCK , WIRING TO THE UNIT MUST BE POL ARIZE D AND GROUN DED .
27 T o ensure proper unit grounding, the ground wire should run from the furnace ground screw located inside the furnace junction box all the way back to the electrical panel. NOTE: Do not use gas piping as an electrical ground. T o confirm proper unit grounding, turn off the electrical power and perform the following check.
28 W1 W2 Y2 Fur nace Integra ted Control M odule Remote Condensin g Unit (T wo-Stage Cooling) Dehumidis tat [Optiona l] Y2 NEU W1 W2 Y2 Thermostat - Two-Stage Heating with Two-Stage Cooling S ET DIP SWIT CH #14 TO ON PO SI TI ON WHEN USING A 2 ‐ ST A GE COO LIN G THERMO STAT .
29 A UX OUT AUX IN L1 NEUTRAL Accessories Wiring If it is necessary for the installer to supply additional line voltage wiring to the inside of the furnace, the wiring must conform to all local codes, and have a minimum temperature rating of 105°C. All line voltage wire splices must be made inside the furnace junction box.
30 G AS V ALVE This unit is equipped with a 24 volt gas valve which modulates by pneumatic linkage to the combustion air blower T a p s for mea- suring the gas supply pressure and manifold pressure are provided on the valve. This is a non-convertible gas valve equipped for natural gas.
31 MANUAL SH UT O F F VALVE (UP ST REAM FROM PIPE UNION) GRO M M E T IN S T ANDA RD GAS LI NE HOLE G AS L IN E PLUG IN G AS L IN E HOLE HEI GHT REQUIRED BY L O CAL CODE PIPE UNION DRIP L EG MA N IFOLD.
32 D IRECT /S TANDARD I NLET P IPING E DGES OF SHEET META L HOLES MAY BE SHARP . U SE GLOVES AS A PRE CAUT ION WHEN RE M OV IN G HOLE PLUGS .
33 3/8" 1/2" 5/8" 3/4" 7/8" 1/2" 3/4" 10 730 1,700 3,200 5,300 8,300 3,200 7,500 20 500 1,100 220 3,700 5,800 2,200 4,200 30 400 920 2,000 2,900 4,700 1,800 4,000 40.
34 Checking Static Pressure (80% Furnace Shown, 90% Similar) B OTTOM R ETURN A IR O PENING [U PFLOW M ODELS ] The bottom return air opening on upflow models utilizes a “lance and cut” method to remove sheet metal from the duct opening in the base pan.
35 6 00 800 1 000 120 0 14 00 1 600 200 0 06 03 __X A --- -- - 5 64* 564 * 672 76 8 08 05 __X A --- -- - -- - 752 * 75 2* 76 8 9 60 1 005 __X A 1 155 __X A -- - --- - -- 940 * 94 0* 9 40* 9 60 6 00 80.
36 • After 2 minutes, the IFC increases to 57% at a rate of 1% per second • After 10 total minutes, the IFC increases to 78% at a rate of 1% per second. • After 20 total minutes, the IFC increases to 100% at a rate of 1% per second for the remainder of the call for heat.
37 • If the differential is equal to or less than 2 degrees, the IFC will follow the conventional 2-S tage algorithm, equivalent to a W1 request and be reflected in the Heat Current Demand S tatus %.
38 AT M O S P H E R E PO RT DIRECTIO N FLO W PS CON NECTI ON Honeywell Model VR9205R Outle t Pressure Ta p 1/8 N PT Inl et Pres sure Ta p 1/8 NPT 2-PI N POW ER CONNECTOR i M a n o m e t e r M a n o m e t e r H o s e O p e n t o A t m o s p h e r e Honeywell Model VR9205R Connected to Manometer 1.
39 3 . Outlet pressure tap connections: Remove the outlet pressure boss plug. Install an 1/8" NPT hose barb fitting into the outlet pressure tap. 4 . Attach a hose and manometer to the outlet pressure barb fitting. 5 . T urn ON the gas supply . 6 .
40 4. Adjust temperature rise by adjusting the circulator blower speed. Increase blower speed to reduce temperature rise. Decrease blower speed to increase temperature rise. Refer to Startup Procedure and Adjustment -Circulator Blower Speeds for speed changing details.
41 • Profile A provides only an OFF delay of one (1) minute at 100% of the cooling demand airflow . OFF 100% CFM 100% CFM 1 min OFF • Profile B ramps up to full cooling demand airflow by first stepping up to 50% of the full demand for 30 seconds. The motor then ramps to 100% of the required airflow .
42 B LOWER H EAT O FF D ELAY T IMINGS The integrated control module provides a selectable heat off delay function. The heat off delay period may be set to 90, 120, 150, 180 seconds using the DIP switches or jumper provided on the control module.
43 For example, assume the system is an air conditioner matched with a furnace. With a call for low stage cooling, the air conditioner will calculate the system’s low stage cooling airflow demand. The air conditioner will then send a fan request along with the low stage cooling airflow de- mand to the furnace.
44 123456 789 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 A O FF O FF - -- - -- -- - -- - -- - --- --- - -- - -- -- - -- - - - - --- -- - - -- - -- B O N O F F - - -- - -- - -- - -- - -- - - - - -- - -- - -- .
45 F OSSIL F UEL A PPLICATIONS This furnace can be used in conjunction with a ComfortNet™ compatible heat pump in a fossil fuel application. A fossil fuel application refers to a combined gas furnac.
46 F URNACE A DVANCED F EATURES M ENUS Subm e nu Ite m Ind ic ati on ( for D is pl a y On ly ; no t U s e r Mo difi ab le ) Nu m ber of H eat S ta ge s (HT S TG ) Dis p lay s t he num be r o f f u r n.
47 T HERMOSTAT M ENU If this furnace is installed with a communicating compatible heat pump, the system is recognized as a dual fuel system. The balance point temperature should be set via the thermostat ad- vanced menu. Navigate to the THERMOST A T menu.
48 F AULT C LEAR S EQUENCE : • Only allowed in standby mode, while display is showing ON. • Hold fault recall push-button for 5-10 seconds (until display starts flashing “—”) and then release. • All faults in the history will have been cleared, and display returns to ON.
49 If the last call for heat was a call for high heat, the air circulating motor will run on the high heating speed for thirty (30) seconds and then switch to the low heating speed for the balance of the heat off delay period (60, 90, 120 or 150 seconds).
50 P RESSURE S WITCHES The pressure switches are normally-open (closed during opera- tion) negative air pressure-activated switches. They monitor the airflow (combustion air and flue products) through the heat ex- changer via pressure taps located on the induced draft blower and the coil front cover .
51 A NNUAL I NSPECTION The furnace should be inspected by a qualified installer , or service agency at least once per year . This check should be performed at the beginning of the heating season. This will ensure that all fur- nace components are in proper working order and that the heating system functions appropriately .
52 B EFORE L EA VING AN I NST ALLA TION • Cycle the furnace with the thermostat at least three times. V erify cooling and fan only operation. • Review the Owner’s Manual with the homeowner and discuss proper furnace operation and maintenance. • Leave literature packet near furnace.
53 T ROUBLESHOOTING C ODES ComfortNet Thermostat Only Symptoms of Abnor mal Operation (Non-communicat ing & Com fortNet™ Thermostat) Diagnostic /Status LED Codes Fault Description Message Code Possible Cau ses Corrective Actions Notes & Cautions x Furnace fails to operate x Integrated c ontrol m odule LED dis play provides n o signal.
54 T ROUBLESHOOTING C ODES ComfortNet Thermostat Only Symptoms of A bnormal Operation (Non-communicat ing & Com fortNet™ Thermostat) Diagnostic/St atus LED Codes Fault Description Message Code Possible Cau ses Corrective Actions Notes & Cautions x Circulator blower runs continuously.
55 T ROUBLESHOOTING C ODES ComfortNet Thermostat Only Symptoms of Abnor mal Operation (Non-comm unicating & Com fortNet™ Thermostat) Diagnostic/St atus LED Codes Fault Description Message Code Possible Cau ses Corrective Actions Notes & Cautions x Furnace fails to opera te on high stage; furnace operates nor mally on low stage.
56 T ROUBLESHOOTING C ODES ComfortNetThermostat Only Symptoms of Abnor mal Operation (Non-communicat ing & Com fortNet™ Thermostat) Diagnostic/St atus LED Codes Fault Description Message Code Possible Cau ses Corrective Actions Notes & Cautions x Operation different than expected or no operation.
57 T ROUBLESHOOTING C ODES ComfortNet Thermostat Only Symptoms of Abnor mal Operation (Non-communicat ing & Com fortNet™ Thermostat) Diagnostic /Status LED Codes Fault Description Message Code Possible Cau ses Corrective Actions Notes & Cautions x Furnace fails to operate.
58 S T A TUS C ODES E 4 IN T E RN AL C O NTR OL FA ULT/N O P OW ER NO RMA L OP ER A T I ON LOCKOUT DUE T O EX C ESSIVE RE TR IES LOW ST A GE P RESSUE SWI T CH STUCK CLOS ED A T STAR T OF HE A TING CYC.
59 HIGH VOL TAGE! Disconnect ALL pow er be fore s ervicing or inst alling thi s unit. Multiple power sources m ay be present. Fai lur e to do so may cause property damage, p er sonal injury or de ath. Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
60 5151 San Felipe Suite 500 Houston, TX 77056 www .goodmanmfg.com • www .amana-hac.com © 2011 Goodman Manufacturing Company , L.P ..
An important point after buying a device Goodman Mfg MVM96 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Goodman Mfg MVM96 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Goodman Mfg MVM96 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Goodman Mfg MVM96 you will learn all the available features of the product, as well as information on its operation. The information that you get Goodman Mfg MVM96 will certainly help you make a decision on the purchase.
If you already are a holder of Goodman Mfg MVM96, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Goodman Mfg MVM96.
However, one of the most important roles played by the user manual is to help in solving problems with Goodman Mfg MVM96. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Goodman Mfg MVM96 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
