Instruction/ maintenance manual of the product RCS10MPA Amana
Go to page of 14
C ommercial M icrow av e O ve n Keep these instr uctions f or futur e r eference. If the oven changes ownership, this manual must accompany oven. Owner's Manual Contents Model Identification ............................ 2 P RECAUTIONS TO AV O I D POSSIBLE EXPOSURE TO EXCESSIVE MICROW A VE ENERGY .
2 Any questions or to locate an authorized Amana servicer , call toll free 1-866-426-2621 inside the U.S.A. or Canada, or 1-319-622-551 1 outside the U.S.A. or Canada. Warranty service must be performed by an authorized Amana servicer . Amana also recommends contacting an authorized Amana servicer if service is required after warranty expires.
3 SA VE THESE INSTRUCTIONS PRECAUTIONS TO A VOID POSSIBLE EXPOSURE T O EXCESSIVE MICROW A VE ENERGY A. DO NOT attempt to operate this oven with the door open since open door operation can result in harmful exposure to microwave energy . It is important not to defeat or tamper with the safety interlocks.
4 SA VE THESE INSTRUCTIONS a. DO NOT overcook food. Carefully attend oven when p aper , plastic, or other combustible materials are placed inside the oven to facilitate cooking. b. Remove wire twist-ties from paper or plastic bags before placing bag in oven.
5 Installation Unpacking Oven • Inspect oven for damage such as dents in door or inside oven cavity . • Report any dents or breakage to source of purchase immediately . Do not attempt to use oven if damaged. • Remove all materials from oven interior .
6 Display and F eatures (some models) ST ART Pad The ST ART pad is used to begin a manual time entry cooking cycle. It is also used to save any changes to programming sequences or user options. STOP/RESET pad The STOP/RESET pad stops a cooking sequence in progress, clears out any remaining time, and also ends a programming or user option cycle.
7 Display and F eatures (some models) Display Some items in the display can be seen but are not available depending on model. Ready Ready displays when an oven control will accept entries. Cooking Displays 33:33 displays total cooking time. When more than one cooking stage is programmed, total time for all stages displays.
8 Using the Oven Control (Electr onic Control) Manual Time Entr y T o cook food using a specific entered time and power level. 1. Open oven door and place food in oven. Close door . • READY displays. Fan and light will turn on. 2. Press TIME ENTRY pad.
9 Programming Pads Oven is shipped from the factory for single p ad programming. T o change the oven default to allow double pad programming, see User Option section. T o change the amount of time or the power level for a preset pad: 1. Open oven door .
10 User Options (Electr onic Control) Changing user options Options such as single or double pad programming, beep volume, and maximum cooking time can be changed to suit individual preferences.
11 Dial Operation Dial option is av aila ble on some models onl y . The switching operation of this microwave oven can cause voltage fluctuations on the supply line. The operation of this oven under unfavorable voltage supply conditions can have adverse effects.
12 Digital Dial Operation Digital Dial option is available on some models only . So...how do I use it? (Digital Dial) Heating 1. Open oven door , place food in oven, and close oven door . 2. Turn time entry knob clockwise until desired time displays. • Factory default setting for cooking time is 10 minutes.
13 Care and Cleaning Replacing Oven Light 1. Disconnect electrical supply . 2. Remove screw from light access panel located on side panel of oven. 3. Turn light bulb counterclockwise to remove. 4. Replace light bulb. Do not over-tighten bulb. Over-tightening may make bulb difficult to remove later .
14 Befor e Calling f or Ser vice ! WARNI NG T o avoid electrical shock which can cause severe personal injury or death, do not remove outer case at any time. Only an authorized Amana servicer should remove outer case. © 2004 Amana Commercial Products Amana, Iowa 52204 Part No.
An important point after buying a device Amana RCS10MPA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Amana RCS10MPA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Amana RCS10MPA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Amana RCS10MPA you will learn all the available features of the product, as well as information on its operation. The information that you get Amana RCS10MPA will certainly help you make a decision on the purchase.
If you already are a holder of Amana RCS10MPA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Amana RCS10MPA.
However, one of the most important roles played by the user manual is to help in solving problems with Amana RCS10MPA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Amana RCS10MPA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
