Instruction/ maintenance manual of the product 1094A Genelec
Go to page of 8
Operating Operating Operating Operating Operating Manual Manual Manual Manual Manual Genelec 1094A and 1092A Genelec 1094A and 1092A Genelec 1094A and 1092A Genelec 1094A and 1092A Genelec 1094A and 1.
General Description The Genelec 1094A and 1092A active subwoofers are powerful low frequency loudspeakers, incorporating all the amplifier and crossover electronics needed to combine them with other loudspeakers and amplifiers. Drivers The 1094A contains a single 385mm (15") long throw cone driver, housed in a 110 litre vented cabinet.
Subw oofer P ositioning 1 2 2 3 3 4 'S o f fi t' M o u n t 5 The figure to the left shows some example subwoofer positions within a room. Unless mentioned otherwise, the vents of the subwoofer should face towards the nearest wall. 1 Recommended position.
Coarse Phase Correction Method The method to coarse align the phase of the system is as follows. • Connect an audio frequency signal generator to one of the channels used in the system. If the signal generator has an unbalanced output use a cable with pin 3 grounded to pin 1 at the input as shown in figure 4 below.
System Connection Subwoofer in two channel Stereo mode. Both left and right stereo channels are fed into the inputs of the subwoofer. Each subwoofer output is then connected to the corresponding main monitor. The following diagrams show the various ways the subwoofer can easily be included into an existing system.
Subwoofer in Analogue Matrix Surround Sound systems. When using a single subwoofer in an analogue matrix surround sound system, such as Dolby Surround or Dolby Pro-Logic, only the front three channels should be connected to the subwoofer inputs (see figure 9 above).
T wo Subw oofer s (mono) in three channel LCR mode. To combine the subwoofers into the system so that both subwoofers produce the bass signals for all three channels, connect the system as shown to the left. Note that the level generated by the subwoofer will be 6dB greater than that generated by a single subwoofer.
Free field frequency response of system (± 2.5 dB): 29 - 80 Hz 33 - 80 Hz Maximum short term sine wave acoustic output in half space, averaged from 35 Hz to 85 Hz @ 1m: >120 dB SPL >115 dB SPL .
An important point after buying a device Genelec 1094A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Genelec 1094A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Genelec 1094A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Genelec 1094A you will learn all the available features of the product, as well as information on its operation. The information that you get Genelec 1094A will certainly help you make a decision on the purchase.
If you already are a holder of Genelec 1094A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Genelec 1094A.
However, one of the most important roles played by the user manual is to help in solving problems with Genelec 1094A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Genelec 1094A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
