Instruction/ maintenance manual of the product ZV850 GE
Go to page of 16
GE Monogram ® Installation Instr uctions 36" Island V ent Hood Model ZV850.
2 Before you begin — Read these instr uctions completely and carefully . IMPORT ANT - Save these instructions for local inspector’s use. IMPORT ANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer - Be sure to leave these instr uctions with the Consumer .
3 Design Infor mation 36" Island Vent Hood Model ZV850 Model Available Required Accessor y This vent hood is designed to be used in vented ceiling mounted installations. NOTE: Accessories to meet proper ceiling height are required to complete the installation.
4 Installation Preparation 36" Island Vent Hood • Tape measure • Knife • Spirit level • Wire cutter • Wire stripper • Wire nuts • Electric drill and 5/32” bit • Phillips screwdr.
5 Installation Preparation 36" Island Vent Hood Duct fittings T otal Equivalent Quantity Equivalent Duct Piece Dimensions Length* Used Length Round, 1 ft. straight (per foot length) 3 -1 ⁄ 4" x 10" 1 ft. straight (per foot length) 90 ° elbow 15 ft.
6 Installation Preparation 36" Island Vent Hood Advance Planning 1 Step Note: The cross framing must be spaced 8-3/4” on the side from centerline to centerline in order to accept the hood mounting screws. Plan the location Determine the exact location of the vent hood.
7 Installation Preparation 36" Island Vent Hood Advance Planning (continued) 1 Step Ductwork • Use the shortest and straightest duct route possible. For satisfactor y per for mance, duct r un should not exceed 100 feet equivalent length for any duct configuration.
8 Installation 36" Island Vent Hood Check Installation Hardware 3 Step Check contents of the required accessory, ZX858, ZX859 or ZX8510. Locate the hardware accessory box packed with the hood and check contents.
9 Installation 36" Island Vent Hood • Align the template with the marks on the ceiling and tape in place. – Be sure the template is oriented cor rectly , with the front of the hood. • Use a plumb to check to be sure the mount- ing holes will provide parallel alignment with the countertop below .
10 Installation 36" Island Vent Hood Wiring • Route house wiring through the ceiling hole and pull a length to reach the hood junction box, approximately 6” below the support. • T ape the wire to the front of the frame support to prevent damage during installa- tion and ser vice.
Installation 36" Island Vent Hood Install Decorative Duct Covers Step 8 11 • Pretap or drive decorative screw into the screw holes on the support frame. This will make screw installation easier . • Separate the two decorative duct covers. • Select the inside (top) cover , which has two screw holes in the top.
12 Installation 36" Island Vent Hood 10 Step Connect Electrical V erify that power is tur ned of f at the source. CAUTION If house wiring is not 2-wire with a ground wire, a ground must be provided by the installer . When house wiring is aluminum, be sure to use U.
13 Installation 36" Island Vent Hood Slide Duct Cover Down, Install Side Utility Bars Step 11 • Hold the decorative duct cover and remove the temporar y stop screw . Retur n the screw to the ser vice manual envelope for future use. • Slide the lower duct cover down onto the hood.
14 Installation 36" Island Vent Hood • Remove protective film on filters. • Tip the filter into the lower slots at the rear of the opening. Lift the filter and pull the knob for ward until the filter rests on the slots. • T o remove the filters, grasp the knob, push the filter towards the rear and tilt down- wards.
Notes 36" Island Vent Hood 15.
Pub. No. 49-8970-1 Dwg. No. 164D3333P197 1999 GE Appliances (N.D. 500) 12/99 04306398 Monogram. ® General Electric Company Louisville, KY 40225 Note: While performing installations described in this book, safety glasses or goggles should be worn.
An important point after buying a device GE ZV850 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE ZV850 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE ZV850 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE ZV850 you will learn all the available features of the product, as well as information on its operation. The information that you get GE ZV850 will certainly help you make a decision on the purchase.
If you already are a holder of GE ZV850, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE ZV850.
However, one of the most important roles played by the user manual is to help in solving problems with GE ZV850. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE ZV850 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
