Instruction/ maintenance manual of the product ZBD1870NSS GE
Go to page of 14
GE Consumer & Industrial Appliances I n s t a l l a t i o n I n s t r u c t i o n s I f yo u ha ve q ue st io ns , ca ll 8 00 . 62 6 .2 00 0 o r vi si t ou r we bs ite a t : ww w .
IMP OR T ANT – The dishwasher MUST be installed to allow for future r emoval fr om the enclosure if service is required. If you received a damaged dishw asher , you should immediately contact your dealer or builder . Optional Accessories – See the Owner ’s Manual for available custom panel kits.
P ARTS SUPPLIED: ■ Two #8 Phillips head wood scr ews, 5/8" long to Two #8 Phillips head wood scr ews, 5/8" long to secure dishwasher to underside of countertop (in literature package).
Installation Preparation PREP ARE DISHW ASHER ENCLOSURE • The rough cabinet opening must be at least 24" deep, 17-5/8" to 18" wide and approximately 34-1/2" high fr om fl oor to underside of the countertop. • The dishwasher must be installed so that drain hose is no more than 10’ in length for pr oper drainage.
Installation Preparation PREP ARE ELECTRICAL WIRING #282 French FOR PERSONAL SAFE TY: Remove house fuse or open cir cuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. #282 French The improper connection of the equipment grounding conductor can r esult in electric shock .
Installation Instructions PREP ARE HOT W A TER LINE • The line may enter from either side, r ear or fl oor within the shaded area shown in Figur e F . • The line may pass through the same hole as the electrical cable and drain hose. Or , cut an additional 1-1/2" dia.
Installation Instructions Figure I • Lay the dishwasher on its back. Remove the four screws securing the toekick to the dishwasher , and remove the toekick . • Remove the single screw just abov e and to the side of each front leveling leg. • Remove the side panels and set the dishwasher upright .
90 ° Elbow Fill Hose Thread Seal T ape Wa ter V a lve Bracket White G r o u nd Black Check That White, Black and Green Dishwasher Wires Are Threaded Thru Hole in Back Remove Junction Box Cover Insert.
Installation Instructions STEP 6 P OSITION W A TER LINE AND HOUSE WIRING • Position water supply line and house wiring on the fl oor of the opening to avoid interference with base of dishwasher and components under dishwasher .
Countertop Figure S Control Panel Counter top Figure T Dishw asher Door 1/2” Min. Installation Instructions STEP 9 P OSITION DISHW ASHER UNDER COUNTER T OP • Push the dishwasher into the cabinet . • Push the sides with your hands. Do not use your knee against the door since door damage will occur .
8 Turn Legs to Adjust Installation Instructions STEP 10 LEVEL DISHW ASHER IMP OR T ANT – Dishwasher must be level for pr oper dish rack operation and wash performance. • Make sure 1/2" minimum gap is maintained (see Figur e T). • Place level on door to check that the dishwasher is level side- to-side.
Installation Instructions STEP 12 CONNECT W A TER SUPPL Y Connect water supply line to 90° elbow . • Slide compression nut , then ferrule over end of water line. • Insert water line into 90° elbow . • Slide ferrule against elbow and secure with compression nut .
11 White G r o u n d Black Check That White, Black and Green Dishwasher Wires Are Threaded Thru Hole in Back Remove Junction Box Cover Insert Power Cord Wires Thru Strain Relief and Tighten Use UL Listed Wire Nuts A C B D Installation Instructions STEP 14 CONNECT POWER SUPPL Y Skip this step if equipped with power cord.
Installation Instructions STEP 16 DISHW ASHER WE T TEST ■ Turn on power supply (or plug power cor d into outlet , Turn on power supply (or plug power cor d into outlet , if equipped). ■ Start the unit to check for leaks. Start the unit to check for leaks.
An important point after buying a device GE ZBD1870NSS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE ZBD1870NSS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE ZBD1870NSS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE ZBD1870NSS you will learn all the available features of the product, as well as information on its operation. The information that you get GE ZBD1870NSS will certainly help you make a decision on the purchase.
If you already are a holder of GE ZBD1870NSS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE ZBD1870NSS.
However, one of the most important roles played by the user manual is to help in solving problems with GE ZBD1870NSS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE ZBD1870NSS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
