Instruction/ maintenance manual of the product PDW9200 Series GE
Go to page of 15
Installation Instructions Built-In Dishwasher If you have questions, call 800-GECARES or visit our website at: www .GEAppliances.com READ CAREFULL Y . KEEP THESE INSTRUCTIONS.
Installation Preparation P ARTS SUPPLIED: T wo #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop or sides of cabinetry . (T aped to top or side of dishwasher .) Side and top trim pieces T rim Panel Accessory Kit (not shown).
Installation Preparation 3 PREP ARE DISHW ASHER ENCLOSURE • The rough cabinet opening must be at least 24" deep, 24" wide and approximately 34-1/2" high from floor to underside of the countertop. • The dishwasher must be installed so that drain hose is no more than 10 feet in length for proper drainage.
Installation Preparation 4 For models equipped with power cord: Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified technician. Cabinet Preparation & Wire Routing • The wiring may enter the opening from either side, rear or the floor within the shaded area.
Installation Instructions 5 Figure G STEP 1 CHECK DOOR BALANCE • With dishwasher on the wood skid, check the door balance by opening and closing the door . • If the door drops when released, increase the spring tension. If the door rises when released, decrease the tension.
Installation Instructions 6 • Do not over tighten 90 ° elbow , water valve bracket could bend or water valve fitting could break. • Position the end of the elbow to face the rear of the dishwasher . STEP 5 INST ALL 90 ° ELBOW • W rap 90 ° elbow with thread seal tape.
Power Cord (If Used) Water Line House Wiring Drain Hose Insulation Blanket Installation Instructions 7 STEP 9 INST ALL TRIM PIECES Skip this step if trim is not supplied with the dishwasher . • Locate trim strips inside dishwasher . • Press trim onto the tub flange on each side.
STEP 10 POSITION DISHW ASHER UNDER COUNTER TOP • Push the dishwasher into the cabinet. • Push at the sides with your hands. Do not use your knee against the door since door damage will occur . • Check that the tub insulation blanket does not get “ bunched-up ” or interfere with the springs as you slide it into the cabinet.
Figure X STEP 1 1 LEVEL DISHW ASHER IMPOR T ANT – Dishwasher must be level for proper dish rack operation and wash performance. TIP: Pull lower rack out, about halfway . Check to be sure the rack does not roll forward or back into dishwasher . If the rack rolls in either direction, the dishwasher must be leveled again.
Installation Instructions 10 STEP 13 CONNECT W A TER SUPPL Y Connect water supply line to 90 ° elbow . • Slide compression nut, then ferrule over end of water line. • Insert water line into 90 ° elbow . • Slide ferrule against elbow and secure with compres- sion nut.
Installation Instructions 11 Figure HH STEP 16 PRE-TEST CHECK LIST Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty . Check to be sure power is OFF . Open door and remove all foam and paper packaging.
Installation Instructions • Align the toekick with the bottom edge and make sure it is against the floor . • Insert and tighten the two toekick attachment screws. The toekick should stay in contact with the floor . TIP: Make sure toekick is against floor to minimize noise.
Specification Created 7/03 250202 TM PDW9700JII – GE Profile ™ Fully Integrated Built-In Dishwasher 24 24 ††† 21-1/4 2-3/4 4 (Adjustable) 33-13/16" MIN.
3/4" Thick Custom Panel T emplate Instructions For PDW9700J Series The custom panel should be sized to your installation situation. See Step 1. For easier installation the custom panel and custom handle should be attached before installing the dishwasher .
Specification Created 7/03 250202 TM PDW9700JII – GE Profile ™ Fully Integrated Built-In Dishwasher T I M E R E M A I N I N G.
An important point after buying a device GE PDW9200 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE PDW9200 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE PDW9200 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE PDW9200 Series you will learn all the available features of the product, as well as information on its operation. The information that you get GE PDW9200 Series will certainly help you make a decision on the purchase.
If you already are a holder of GE PDW9200 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE PDW9200 Series.
However, one of the most important roles played by the user manual is to help in solving problems with GE PDW9200 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE PDW9200 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
