Instruction/ maintenance manual of the product PB970 GE
Go to page of 12
1 31-10652 02-07 JR Installation Free-Standing Instructions Electric Ranges Models PB970, PB975 BEFORE YOU BEGIN Read these instructions completely and carefully . • IMPOR T ANT — Save these instructions for local inspector’ s use. • IMPOR T ANT — Observe all governing codes and ordinances.
TOOLS YOU WILL NEED FOR YOUR SAFETY : All rough-in and spacing dimensions must be met for safe use of your range. T o reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above the cooktop should be avoided.
3 Installation Instructions PREP ARE THE OPENING See illustrations for all rough-in and spacing dimensions. The range may be placed with 0” clearance (flush) at the back wall and side walls of the cabinet. NOTE: Use a 4 ′ power cord to prevent interference.
4 Installation Instructions ELECTRICAL CONNECTIONS Y ou must use a 3-wire, single-phase A.C. 208Y/120 V olt or 240/120 V olt, 60 hertz electrical system. If the electrical service provided does not meet the above specifications, have a licensed electrician install an approved outlet.
5 Installation Instructions POWER CORD AND STRAIN RELIEF INST ALLA TION Remove the terminal block cover (on the back of the range) by removing the screw , using a 1/4” nut driver . Do not discard the screw . Remove the knockout ring (1 3 ⁄ 8 ″ ) located on bracket directly below the terminal block.
6 Installation Instructions ELECTRICAL CONNECTIONS (CONT .) 4-WIRE POWER CORD INST ALLA TION W ARNING: The neutral wire of the supply circuit must be connected to the neutral terminal located in the lower center of the terminal block. The power leads must be connected to the lower left and the lower right terminals of the terminal block.
7 Installation Instructions 3-WIRE CONDUIT INST ALLA TION Loosen the 3 lower terminal screws from the terminal block. Insert the center bare wire (white/neutral) tip through the bottom center terminal block opening. On certain models, the wire will need to be inserted through the ground strap opening and then into the bottom center block opening.
8 Installation Instructions INST ALL THE RANGE ANTI-TIP DEVICE INST ALLA TION An Anti-T ip bracket is supplied with instructions for installation in a variety of locations. The instructions include all necessary information to complete the installation.
LEVEL THE RANGE Install the oven shelves in the oven and position the range where it will be installed. Check for levelness by placing a spirit level or a cup, partially filled with water , on one of the oven shelves. If using a spirit level, take two readings—with the level placed diagonally first in one direction and then the other .
10 Notes.
11 Notes.
12 Printed in the United States.
An important point after buying a device GE PB970 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE PB970 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE PB970 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE PB970 you will learn all the available features of the product, as well as information on its operation. The information that you get GE PB970 will certainly help you make a decision on the purchase.
If you already are a holder of GE PB970, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE PB970.
However, one of the most important roles played by the user manual is to help in solving problems with GE PB970. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE PB970 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
