Instruction/ maintenance manual of the product ZET757BW GE Monogram
Go to page of 20
GE Monogram ® Installation Instr uctions 30" Built-In Ovens Models ZET757WW ZET757BW ZET737WW ZET737BW.
Before you begin—Read these instr uctions completely and carefully . IMPORT ANT: Save these instr uctions for local inspector’ s use. IMPORT ANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTE TO INST ALLER: Be sure to leave these instr uctions with the Consumer .
Models available ZET757WW White double convection oven ZET757BW Black double convection oven ZET737WW White single convection oven ZET737BW Black single convection oven Dimensions and clearances Doubl.
Cabinet style options Design Infor mation Built-In Ovens Front Framed Partial Overlay Door Front Framed Full Overlay Door Frameless Monogram ovens are installed directly into a wall or wall oven cabinetr y , 30" minimum width. The front sur face of the ovens will be nearly flush with sur- rounding cabinetr y .
Cabinetr y Built-In Ovens 5 Ovens are designed for installation in a cabinet 30" min. wide. • Cut 2" x 4" runners of appropriate length or solid shelf to support oven. • Attach runners or solid shelf in opening as shown. • Runners must be level and rigidly mounted.
A Cabinetr y Built-In Ovens 6 Framed cabinet single oven DIMENSIONS A Cabinet Width 30" Min. B Cutout Width 28-1/2" Min., 28-5/8 Max. C Cutout Height 27-1/4" Min.
Cabinetr y Built-In Ovens 7 Frameless cabinets Frameless Use the infor mation in this dimension drawing for typical frameless cabinets. The front face of the oven will be flush with cabinetr y doors or drawers. Whenever possible, order 30" frameless cabinet with the cutout sized to fit the oven.
Cabinetr y Built-In Ovens 8 Single oven installed below a countertop See Cooktop Installation Instructions For Cutout 27-1/4" Min. 27-5/16" Max. 3/4" Support Platform and 2 x 4‘s Required, Must Support 150 lbs. Junction Box 22" Min.
9 Provide oven supports Cabinetr y Modification Suggestions Built-In Ovens The ovens may be supported by either a solid bottom or 2 x 4 runners. • The support must be level and rigidly mounted, flush with the bottom edge of the cutout.
10 Determine need for filler panels Filler panel construction If the cabinets being used have an opening that is taller than the maximum dimensions indicated for the ovens, filler panels can be made to fill the gaps. Stock filler strips are usually available or for larger gaps order an extra drawer front.
11 Cut rail for filler panel Cut appearance panel Determine location of cleats • T o find the exact position of the cleats, place the appearance panel onto the cabinet in desired position and align to match the other drawers and doors. • Use a pencil to mark the back side of the panel where it meets the cabinet corners.
Cabinetr y Modification Suggestions Built-In Ovens 12 Cut and secure cleats to filler panel Secure rail to appearance panel Secure assembled filler panel to cabinet • Place filler panel in proper position.
13 Installation Built-In Ovens • Outlet box • Electrical cable—3-conductor or 4-conductor wire—as required by local codes • Flexible power cable connector • Electrician’s pliers Note: Do not use an extension cord with these appliances.
Installation Built-In Ovens 14 Remove oven door CAUTION Do not lift oven or oven door by handle. Door glass breakage or handle damage may occur. Glass surface of door face extends beyond door frame on each side; be careful not to impact this exposed glass.
15 Installation Built-In Ovens • When connecting to a 4-conductor branch circuit: – Connect oven red lead to branch circuit red lead. – Connect oven black lead to branch circuit black lead. – Break connection between oven white lead and oven bare copper conductor .
Installation Built-In Ovens 16 Attach lower trim • Attach the lower trim at the bottom of the oven: – Align the key slot on the trim piece to the rivets on the oven. – Push the trim down until it snaps into place. CAUTION The bottom of the trim provides an opening for cooling air to enter the cabinet.
17 Notes Built-In Ovens.
Notes Built-In Ovens 18.
Notes Built -In Ovens 19.
Monogram. ® General Electric Company Louisville, KY 40225 Pub. No. 49-8803 1997 GE Appliances (N.D. 617) 2/97 NOTE: While performing installations described in this book, safety glasses or goggles should be worn.
An important point after buying a device GE Monogram ZET757BW (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE Monogram ZET757BW yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE Monogram ZET757BW - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE Monogram ZET757BW you will learn all the available features of the product, as well as information on its operation. The information that you get GE Monogram ZET757BW will certainly help you make a decision on the purchase.
If you already are a holder of GE Monogram ZET757BW, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE Monogram ZET757BW.
However, one of the most important roles played by the user manual is to help in solving problems with GE Monogram ZET757BW. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE Monogram ZET757BW along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
