Instruction/ maintenance manual of the product JT980 GE
Go to page of 16
1 31-10663 1-07 JR Installation 30” Built-In T rivection ™ Instructions W all Oven JT930, JT980, ZET3038, ZET3058 BEFORE YOU BEGIN Read these instructions completely and carefully . • IMPOR T ANT — Save these instructions for local inspector’ s use.
2 Installation Instructions PREP ARE TO INST ALL THE OVEN TOOLS YOU WILL NEED MA TERIALS YOU MA Y NEED Wire Nuts Junction Box 60” of String for Single Ovens 96” of String for Double Ovens Adjustab.
3 Installation Instructions PRE-INST ALLA TION All installation information on the following pages is to be used for SINGLE and DOUBLE oven installation! Remove packaging materials. Check behind hinges. Remove plastic on trims and panel, all tape around the oven, and any shipping screws securing the oven to the base pad.
4 Installation Instructions SINGLE BUIL T -IN OVEN CUTOUT OPTIONS W ALL MOUNT—SINGLE BUIL T -IN OVEN OPTION Cabinet Width 30” Recommended Cutout Location from Floor 32 1/2” Cutout Depth 23 1/2” Min. Cutout Width 28 1/2” Min. 28 5/8” Max. Cutout Height 27 1/4” Min.
Installation Instructions W ALL MOUNT—SINGLE BUIL T -IN OVEN BELOW AN ADV ANTIUM OVEN OPTION • When installed over a single wall oven, allow at least 2” between the two openings. This separation will provide clearance for bottom overlap of the Advantium oven and top overlap of the single wall oven.
6 UNDER COUNTER—SINGLE BUIL T -IN OVEN OPTION D T op and/or side fillers may be necessary if unit is positioned between existing cabinets. Be sure they are attached securely , since they will anchor the oven in the cabinet. 25” 24” 27 1/4” Min.
Installation Instructions 7 DOUBLE BUIL T -IN OVEN CUTOUT CUTOUT FOR DOUBLE BUIL T -IN OVEN Cabinet Width 30” Recommended Cutout Location from Floor 12” Cutout Depth 23 1/2” Min. Cutout Width 28 1/2” Min. 28 5/8” Max. Cutout Height 51 13/16” Min.
ON DOUBLE W ALL OVEN MODELS, REMOVE THE LOWER DOOR ONL Y (CONT .): Close door to the door removal position, which is halfway between the broil stop position and fully closed.
Installation Instructions 9 9 ELECTRICAL CONNECTIONS ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency , and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate.
10 Installation Instructions ELECTRICAL CONNECTIONS (CONT .) CONNECT CONDUIT With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below . Position the conduit in such a manner that it will lie behind the oven in a natural loop when the oven is installed.
11 Installation Instructions THREE-CONDUCTOR BRANCH CIRCUIT CONNECTION When connecting to a three-conductor branch circuit, if local codes permit: Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut.
12 Installation Instructions SECURE THE OVEN IN THE OPENING SLIDE THE OVEN INTO THE OPENING Loop (do not tie) the correct length of string around the conduit before the oven is slid into place. This will keep the conduit from falling improperly behind the oven.
13 Installation Instructions T o install a single metal bottom trim assembly (on some models), see Step 11. T o install a metal bottom trim with a plastic bottom trim (on some models), see Steps 11 and 12. INST ALL THE MET AL BOTTOM TRIM With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening.
14 Installation Instructions REPLACE THE LOWER OVEN DOOR ON DOUBLE W ALL OVEN MODELS ON DOUBLE W ALL OVEN MODELS, REPLACE THE LOWER DOOR: Firmly grasp both sides of the door at the top. With the door at the same angle as the removal position, seat the indentation of the hinge arm into the bottom edge of the hinge slot.
15 Installation Instructions FINAL CHECKLISTS PRE-TEST CHECKLIST Remove all protective film. Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Check that the bottom trim is installed properly (see Steps 11 and 12).
16 Printed in the United States.
An important point after buying a device GE JT980 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE JT980 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE JT980 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE JT980 you will learn all the available features of the product, as well as information on its operation. The information that you get GE JT980 will certainly help you make a decision on the purchase.
If you already are a holder of GE JT980, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE JT980.
However, one of the most important roles played by the user manual is to help in solving problems with GE JT980. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE JT980 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
