Instruction/ maintenance manual of the product JS905 GE
Go to page of 20
1 MA TERIALS YOU MA Y NEED 3-Wire Cord 4 ’ long (UL Approved 40 or 50 AMP) Lag Bolts Anchor Sleeves (For Anti-Tip Bracket Mounted on Concrete Floors Only) 4-Wire Cord 4 ’ long OR If you have questions, call 1.800.GE.CARES or visit our website at: ge.
2 IMPORT ANT SAFETY INSTRUCTIONS Installation Instructions For Y our Safety All rough-in and spacing dimensions must be met for safe use of your range. Electricity to the range can be disconnected at the outlet without moving the range if the outlet is in the preferred location (remove lower drawer).
3 Inspect Installation Location Refer to alternate construction section for the following non-standard installations. a. Counter opening extends to the wall: Maintop Filler (supplied with the range.) (See page 15, section AA, for Installation Instructions) or Backguard (Kit JXS36XX or JXS39SS).
4 Installation Instructions Pre-Installation Checklist cont. Door removal is not a requirement for installation of the product, but is an added convenience. T o remove the door: Open the oven door as far as it will go. Push both hinge locks down toward the door frame, to the unlocked position.
5 Installation Instructions Pre-Installation Cutout and Required Clearances 1 If cabinets are placed less than 30 ” above the range, see Alternate Construction, section AF , on page 16. 30 ” ranges conform to U.L. requirements for 0 ” spacing from vertical walls below countertops.
6 Installation Instructions Standard Installation If the construction of your cabinet cannot provide a 1/4 ” flat area at the back of the countertop opening, consider changing the countertop to accommodate this dimension. See Alternate Construction section.
7 (Continued on following page) Installation Instructions Electrical Connections ALL NEW CONSTRUCTIONS, MOBILE HOMES AND INST ALLA TIONS WHERE LOCAL CODES DO NOT ALLOW GROUNDING THROUGH NEUTRAL, REQUIRE A 4-CONDUCTOR UL-LISTED RANGE CORD. Y ou must use a 3-wire, single-phase A.
8 Installation Instructions Electrical Connections cont. 3 POWER CORD AND STRAIN RELIEF INST ALLA TION A Remove the wire cover (on the back of the range) by removing 2 screws, using a 1/4 ″ nut driver . Do not discard these screws. Wire Cover B Remove the knockout ring (1-3/8 ″ ) located on bracket directly below the terminal block.
9 Installation Instructions Electrical Connections cont. 4 3-WIRE POWER CORD INST ALLA TION W ARNING: The neutral or ground wire of the power cord must be connected to the neutral terminal located in the center of the terminal block. The power leads must be connected to the lower left and the lower right terminals of the terminal block.
10 Installation Instructions Electrical Connections cont. 6 3-WIRE CONDUIT INST ALLA TION A Loosen the 3 lower terminal screws from the terminal block.
11 Installation Instructions Installing the Range FIG. 1 Decide whether the bracket will be installed on the right or left side of the range opening. Place the bracket as shown in Fig. 1. FIG. 2 I NST ALLING THE BRACKET IN WOOD OR CONCRETE 10 INST ALLA TION — WOOD CONSTRUCTIONS Locate the centers of the 4 holes identified in Fig.
12 Installation Instructions Installing The Range cont. SLIDE RANGE INTO OPENING Position the range in front of the cabinet opening. Make sure that the glass which overhangs the countertop clears the countertop. If necessary , raise the unit by lowering the leveling legs.
13 Installation Instructions Installing The Range cont. REPLACING THE OVEN DOOR Lift the oven door by placing one hand on each side. The door is heavy , so you may need help.
14 Installation Instructions Check to make sure the circuit breaker is closed (Reset) or the circuit fuses are replaced. Be sure power is in service to the building. Check to be sure that all packing materials and tape on metal panel (if applicable) under control knobs and drawer have been removed.
15 Wall Must Be Flat Must Be Flat Must Be Level Must Be Level 31-1/8 ” 30 ” Smooth Cut 25 ” Installation Instructions Alternate Construction OPTIONAL MAINTOP FILLER OR BACKGUARD KIT If counter opening extends to the wall, it will require Maintop Filler Kit (supplied with the range) or Backguard Kit (JXS36XX or JXS39SS) to close the gap.
16 Installation Instructions Alternate Construction cont. COUNTERT OPS HIGHER THAN 36-1/2 ” If countertop height is between 36-1/2 ” and 38 ” , a lower trim kit (JXS56XX) is recommended.
17 NOTES.
18 NOTES.
19 NOTES.
20 NOTES.
An important point after buying a device GE JS905 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE JS905 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE JS905 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE JS905 you will learn all the available features of the product, as well as information on its operation. The information that you get GE JS905 will certainly help you make a decision on the purchase.
If you already are a holder of GE JS905, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE JS905.
However, one of the most important roles played by the user manual is to help in solving problems with GE JS905. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE JS905 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
