Instruction/ maintenance manual of the product JGSP28 GE
Go to page of 16
TOOLS YOU WILL NEED MA TERIALS YOU MA Y NEED 1 229C 4053P596 31-10598 10-04 JR Questions? Call 800.GE.CARES (800.432.2737) or Visit our W ebsite at: www .GEAppliances.com Installation Gas Slide-In Range Instructions JGSP28 BEFORE YOU BEGIN Read these instructions completely and carefully .
FOR YOUR SAFETY : W ARNING — If the information in this manual is not followed exactly , a fire, explosion or gas leak may result, causing property damage, personal injury or death.
3 Installation Instructions ANTI-TIP DEVICE W ARNING — T o reduce the risk of tipping, the appliance must be secured by properly installed Anti-T ip bracket packed with this appliance. T o check if the bracket is installed and engaged properly , carefully tip the range forward.
INSPECT INST ALLA TION LOCA TION Refer to alternate construction section for the following non-standard installations. Counter opening extends to the wall: Maintop Filler (supplied with the range) (see page 15 for Installation Instructions) or Backguard Kit (JXS32XX).
REMOVE THE DOOR IF NECESSARY Door removal is not a requirement for installation of the product, but is an added convenience. T o remove the door: UNLOCK HINGES Push both hinge locks down toward the door frame, to the unlocked position. This may require a flat blade screwdriver .
6 Installation Instructions PRE-INST ALLA TION CHECKLIST (CONT .) PRE-INST ALLA TION CUTOUT AND REQUIRED CLEARANCES If cabinets are placed less than 30 ″ above the range, see Alternate Construction, Step 19F , on page 16. NOTE: Product meets ANSI Z21.
7 Installation Instructions ELECTRICAL CONNECTIONS INST ALLA TION—ELECTRICAL CONNECTIONS Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.
MAKING THE CONNECTIONS (cont.) Install 1/2 ″ flare union adaptor to the 1/2 ″ NPT elbow on pressure regulator . Connect flexible appliance connector to flare union. Move range into approximate position and connect flexible connector to gas supply line with proper flare union adaptor .
INST ALL THE ANTI-TIP BRACKET LOCA TE THE BRACKET a. Decide whether the bracket will be installed on the right or left side of the range opening. b. Place the bracket as shown in Fig. 1. A 12 Rear leveling leg Wa l l FLOOR-CONCRETE 9 Installation Instructions INST ALL THE RANGE INST ALL THE ANTI-TIP BRACKET (cont.
SLIDE RANGE INTO OPENING Position the range in front of the cabinet opening. Make sure that the cooktop edges that overhang the countertop clear the countertop. If necessary , raise the unit by lowering the leveling legs. Push while lifting the range into the opening, until the range is within 2 ″ of engaging the anti-tip bracket.
REPLACE THE OVEN DOOR NOTE: The oven door is heavy . Y ou may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. Lift the oven door by placing one hand on each side. The door is heavy , so you may need help.
12 Installation Instructions INST ALL THE RANGE (CONT .) COOKTOP BURNERS ASSEMBLE THE BURNERS CAUTION: The electrode of the spark igniter is exposed. Be careful not to snag the electrode of the spark igniter with a cleaning cloth. Damage to the igniter could occur .
Installation Instructions PRESSURE TEST INFORMA TION The maximum allowable supply pressure for the regulator is 14 ″ W .C. The minimum supply pressure needed to check the regulator setting is 7 ″ W .
14 Installation Instructions INST ALL THE RANGE (CONT .) BAKE AND BROIL BURNERS If the bake and/or broil burners have lifting or “lazy” (floating) flames or you have a yellow flame, perform the following procedures: CHECKING THE OVEN BURNERS T o check the bake burner flames with the oven door in the closed position: 1.
15 Installation Instructions AL TERNA TE CONSTRUCTION PREP ARA TION OPTIONAL MAINTOP FILLER OR BACKGUARD KIT If counter opening extends to the wall, it will require Maintop Filler Kit (supplied with the range) or Backguard Kit (JXS32XX) to close the gap.
Installation Instructions INST ALL THE RANGE (CONT .) AL TERNA TE CONSTRUCTION PREP ARA TION (cont.) FOR CABINET OPENINGS APPROXIMA TEL Y 30-3/8 ″ If range is installed in cabinet opening approximately 30-3/8 ″ , the V ertical Side T rim Kit (JXS86XX) should be used to cover gaps between range sides and cabinet.
An important point after buying a device GE JGSP28 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE JGSP28 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE JGSP28 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE JGSP28 you will learn all the available features of the product, as well as information on its operation. The information that you get GE JGSP28 will certainly help you make a decision on the purchase.
If you already are a holder of GE JGSP28, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE JGSP28.
However, one of the most important roles played by the user manual is to help in solving problems with GE JGSP28. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE JGSP28 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
