EN
GE logo
Official user manual

GE ECD

24 pages·2.1 MB·Oven·PDF·ENDEFRITNLJA
GE ECD
Table of Contents 80 sections Use and Care Manual · Classic Wall Oven · Place Serial Number Label Here · I mportant S afety I nstructions · … ShowHide
Use and Care Manualp.1Classic Wall Ovenp.1Place Serial Number Label Herep.1I mportant S afety I nstructionsp.3DANGERp.3WARNINGp.3Safety Symbols and Labelsp.3READ AND SAVE These Instructionsp.3General Safety Precautionsp.4Getting Startedp.5Setting The Time Of Dayp.5Oven Featuresp.5Control Panelp.6Control Panel - Epicurep.6® Models ECD227 and ECD230p.6® Models ECS227 and ECS230p.6® Models ECS127, ECS130 and ECS136p.6Control Panel - Millenniap.6Control Panel - Preferencep.7Oven Rack Positionsp.8Oven Modesp.9Oven Mode Selectionp.9PURE CONVECTIONp.9Pre-Heating the Ovenp.9NOTE:p.9What Is Pure Convection?p.10Bakeware Tips:p.10Heated Air Circulation in Convection Modesp.10Baking and Roasting Tipsp.10Clock Displaying Broil (double oven)p.10BROILING TIPS:p.11Common Baking Problemsp.11Delay Timed Cookingp.11IMPORTANT:p.11Delay Timed Cooking (Continued)p.12Using the Meat Probep.12Important things to know about the meat probe:p.12Setting the Oven for Delay Timed Cookingp.12Meat Probep.12Dehydrating/Defrostingp.13To use the minute timer:p.13NOTES:p.13165˚F*p.13180˚Fp.13165˚Fp.13C are and C leaningp.14Porcelain Surfacesp.14Convection Filter Removalp.14To Start the Self-Clean Cycle:p.15Convection Filter Installationp.15Self-Cleaningp.15Display - Self-Cleaning Modep.15To Prepare the Oven for Self-Cleaning:p.15Self-Cleaning (Continued)p.16Adjusting the Oven Temperaturep.16To calibrate the oven temperature:p.16Self-Cleaning Tips:p.16TIMER 1 CLOCK STOP TIME TIMER 2p.16Display When Calibrating the Ovenp.16Replacing the Oven Lightp.17Accessoriesp.17Replacement Oven Light Bulbp.17Stainless Steel Cleanerp.17Oven Light Assemblyp.17B efore Y ou C all F or S ervicep.18Problem Solution Guidep.18PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTIONp.18Oven Failure Codesp.19S ervice and P roduct W arrantyp.20Product Maintenancep.20What Is Not Coveredp.20CERTIFICATE OF WARRANTIESp.20DACOR WALL OVENSp.20FULL ONE YEAR WARRANTYp.20LIMITED FIRST YEAR WARRANTYp.20N otesp.21NO POSTAGEp.23NECESSARYp.23IF MAILEDp.23IN THE UNITED STATESp.23
Page 1 of the GE ECD user manual — Place Serial Number Label Here
Page 1 · click to enlarge
Page 1
GE ECD — Use and Care Manual diagram (page 1)
Fig. 1 · Use and Care Manual

Use and Care Manual

Classic Wall Oven

For use with ECD, ECS, MCD, MCS, PCD and PCS series models

GE ECD — Use and Care Manual diagram (page 1)
Fig. 2 · Use and Care Manual

Ta b l e o f C o n t e n t s

Place Serial Number Label Here

Part No. 65031 Rev. J

Page 2 of the GE ECD user manual — Use and Care Manual
Page 2 · click to enlarge
Page 2
GE ECD — Use and Care Manual diagram (page 2)
Fig. 3 · Use and Care Manual
Page 3 of the GE ECD user manual — READ AND SAVE These Instructions
Page 3 · click to enlarge
Page 3

I mportant S afety I nstructions

Installer: Leave these instructions with the appliance.

DANGER

IMPORTANT: To avoid the possibility of explosion or fire, do not store or use combustible, flammable or explosive vapors and liquids (such as gasoline) inside or in the vicinity of this or any other appliance. Keep items that could explode, such as aerosol cans away from the burners and oven. Do not store flammable or explosive materials in adjacent cabinets or areas.

Consumer: Read this use and care manual completely before using this appliance. Save it for future reference. It contains important use and care information. Keep your sales receipt or canceled check in a safe place. Proof of original purchase date is required for warranty service.

WARNING

If you have any questions, call:

Dacor Customer Service (800) 793-0093 (U.S.A. and Canada) Monday — Friday 6:00 a.m. to 5:00 p.m. Pacific Time

Web sitewww.Dacor.com

WARNING

Have the complete model and serial number identification of your appliance ready.

For service and warranty information, see page 18.

Since Dacor is constantly improving the quality and performance of our appliances, we may need to make changes to the appliance without revising this manual. Important Information About Safety Instructions

The Important Safety Instructions and warnings in this manual cannot cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this appliance.

Always contact the manufacturer about problems or conditions you do not understand.

Safety Symbols and Labels

GE ECD — Safety Symbols and Labels diagram (page 3)
Fig. 4 · Safety Symbols and Labels

READ AND SAVE These Instructions

Model Number Serial Number Date of Purchase

Page 4 of the GE ECD user manual — WARNING
Page 4 · click to enlarge
Page 4

I mportant S afety I nstructions

General Safety Precautions

To reduce the risk of fire, electric shock, serious injury or death when using your oven, follow basic safety precautions, including the following:

WARNING

WARNING

If you receive a damaged product, immediately contact • your dealer or builder. Do not install or use a damaged appliance.

Do not use the oven for storage. •

Clean and maintain the oven regularly as instructed in this • manual. Keep the entire oven free of grease that could catch fire. Clean only those parts listed in this manual.

Make sure that the oven has been properly installed • and grounded by a qualified installer according to the accompanying installation instructions. Have the installer show you the location of the fuse or junction box so that you know where and how to turn off power to the oven.

Do not touch the outside surfaces of the oven during the • self-clean cycle. They will be hot.

Use cookware only for its intended purpose. Check the • manufacturer’s recommendations before use to determine if a utensil is suitable for use in an oven. Certain types of glass, ceramic and earthenware are not suitable for use in the oven. Personal injury or damage may result from the improper use of cookware.

Do not install, repair or replace any part of the oven unless • specifically recommended in the literature accompanying it. A qualified service technician should perform all other service.

Before performing any type of service, make sure that • the electrical power to the oven is turned off at the circuit breaker or fuse box.

Exercise caution when opening the oven door. Let hot air or • steam escape before looking or reaching inside.

Use extreme caution if adding water to food in the oven. • The steam can cause serious burns or scalds.

Only use the oven for cooking tasks expected of a home • appliance as outlined in this manual. This oven is not intended for commercial use.

Use only dry pot holders when removing food and • cookware from the oven. Wet pot holders can cause steam burns.

DO NOT TOUCH THE INTERIOR SURFACES OF THE • OVEN DURING OR IMMEDIATELY AFTER USE.

For your safety, do not use the oven to cook without the • convection filter(s) installed. When the filter is not installed, the spinning fan blades at the back of the oven are exposed.

Make sure individuals who use the oven are able to operate • it properly.

Never allow anyone, including children to sit, stand or climb • on any part of the oven including the door. Doing so may cause tipping, damage, serious injury or death.

Do not allow food to sit in the oven for more than one hour • before or after cooking. Eating spoiled food can result in food poisoning.

Do not leave children alone or unattended in the area • around the oven. Do not allow children to play with the controls, pull on the handle(s) or touch other parts of the oven. Do not store items of interest to children above the oven. Children could be burned or injured while climbing on the appliance.

Do not leave metal objects, such as aluminum foil, the meat • probe or cookie sheets on the bottom of the oven. Do not allow the broil elements on the ceiling of the oven chamber to be covered up. Do not line the oven with aluminum foil or other materials. Doing so may cause the oven or the items in it to overheat, creating a fire hazard or causing property damage.

Do not tamper with the controls. •

To prevent the unit from tipping forward and to provide • stable installation, make sure the oven is secured to the cabinet according to the accompanying installation instructions.

Non-stick coatings, when heated, can be harmful to birds. • Remove birds to a separate, well-ventilated room during cooking.

Do not heat unopened food containers such as baby food • jars and cans. Pressure build up may cause the container to burst and cause injury.

Before Self-Cleaning the oven, remove the broiler grill and • pan, oven racks, convection filter and any other utensils, and wipe up excess spills. DO NOT LEAVE FOOD OR COOKING UTENSILS, ETC., IN THE OVEN DURING THE SELF-CLEAN CYCLE.

Do not use water on grease fires. A violent steam explosion • may result. Smother any flames with a lid, cookie sheet or flat tray. Use baking soda or a foam extinguisher to extinguish flaming grease. Be careful to avoid getting burned.

Do not clean the door gasket, because rubbing, moving • or in any way damaging the gasket, may eliminate the required tight door seal.

Keep flammable items, such as paper, cardboard, plastic • and cloth away from and out of the oven. Do not allow pot holders to touch hot surfaces.

Do not use commercial oven cleaners or oven liner • protective coatings on any part of the oven. Do not use caustic cleaners or detergents on this appliance, as these may cause permanent damage. Do not use aerosol cleaners, as these may be flammable or cause corrosion of metal parts.

Do not use towels or bulky cloth as pot holders. Do not • wear loose or hanging apparel while using the oven. Do not allow clothing to come into contact with the interior of the oven and surrounding areas during and immediately after use.

Do not allow acids (citrus juices, tomato sauces, etc.) to • remain on the oven cell surfaces. The porcelain finish may stain.

Page 5 of the GE ECD user manual — Oven Features
Page 5 · click to enlarge
Page 5

Getting Started

Setting The Time Of Day

Before using your oven, become familiar with the features and control panel layout (see pages 4 and 5).

Follow these two steps to set the correct time of day:

Press the 1. CLOCK key. The time of day will flash, “AM” or “PM” will be displayed, and “TIME” will flash in the display.

  • Below the oven mode touch keys are three touch keys labeled CANCEL
  • SECURE , LIGHT and COOK TIME . The CANCEL
  • SECURE key enables the user to cancel the selection of an oven mode or delay timed program, or disable the control panel. The LIGHT key turns the interior oven light on and off. The LIGHT key will remain functional if the control panel has been disabled. The COOK TIME key is used to select the length of time for a cooking process in delay timed cooking mode.

Press the key 2. “+” or “–” until the correct time of day is displayed and release. Securing the Controls

To avoid accidentally turning the oven on, activate the secure feature. Press and hold the CANCEL • SECURE key for approximately three seconds. Doing so will disable the control panel and allow cleaning the controls without accidentally starting any functions. Three beeps will sound and “OFF” will appear in the display when the control panel has been secured.

Clock functions are selected by pressing the keys located below the clock display and oven mode keys. Oven functions are chosen by pressing the key for the desired mode. Once a clock or oven function has been chosen, a description of the selection will flash in the clock display area.

To re-activate the control panel, again push and hold the CANCEL • SECURE key for three seconds. Three beeps will sound and “OFF” will disappear from the display.

GE ECD — Getting Started diagram (page 5)
Fig. 5 · Getting Started

Oven Features

Page 6 of the GE ECD user manual — Control Panel - Millennia
Page 6 · click to enlarge
Page 6

Control Panel

GE ECD — Control Panel diagram (page 6)
Fig. 6 · Control Panel

Control Panel - Epicure

® Models ECD227 and ECD230

GE ECD — Control Panel - Epicure diagram (page 6)
Fig. 7 · Control Panel - Epicure

Control Panel - Epicure

® Models ECS227 and ECS230

GE ECD — Control Panel - Epicure diagram (page 6)
Fig. 8 · Control Panel - Epicure

Control Panel - Epicure

® Models ECS127, ECS130 and ECS136

GE ECD — Control Panel - Epicure diagram (page 6)
Fig. 9 · Control Panel - Epicure

Control Panel - Millennia

™ Models MCD227 and MCD230

GE ECD — Control Panel - Millennia diagram (page 6)
Fig. 10 · Control Panel - Millennia

Control Panel - Millennia

™ Models MCS227 and MCS230

Page 7 of the GE ECD user manual — Control Panel - Preference
Page 7 · click to enlarge
Page 7
GE ECD — Control Panel - Preference diagram (page 7)
Fig. 11 · Control Panel - Preference

Control Panel - Millennia

™ Models MCS127 and MCS130

GE ECD — Control Panel - Millennia diagram (page 7)
Fig. 12 · Control Panel - Millennia

Control Panel - Preference

™ Models PCD227 and PCD230

GE ECD — Control Panel - Preference diagram (page 7)
Fig. 13 · Control Panel - Preference

Control Panel - Preference

GE ECD — Control Panel - Preference diagram (page 7)
Fig. 14 · Control Panel - Preference

Control Panel - Preference

™ Model PCS230 · ™ Model PCS130

Page 8 of the GE ECD user manual — Oven Rack Positions
Page 8 · click to enlarge
Page 8
GE ECD — Oven Rack Positions diagram (page 8)
Fig. 15 · Oven Rack Positions

Three chrome-plated convection racks are provided in the oven. Always remember to position the racks prior to heating the oven. Also, remove the oven racks prior to self-cleaning to prevent permanent discoloration of the racks.

The porcelain rack supports provide six heights for positioning of the oven racks.

To install a rack, align the left and right edges of the rack with the horizontal guide rails of the rack supports, then slide the rack into the oven. GlideRack

Dacor’s GlideRack oven rack is designed to install effortlessly and glide at a full extension. The full extension of the rack allows you to slide pizza on and off with great ease when using Dacor’s optional pizza stone (model number ABS20). It is also great for large roasts in large roasting pans. It will also allow you to baste more easily and check temperatures of the food more safely and quickly.

Oven Rack Positions

Helpful Hints When Using Your GlideRack Oven Rack

The GlideRack oven rack works particularly well with heavier • items, but you can use it during any type of baking, broiling or roasting in your Dacor oven.

The GlideRack racks need to be spaced out when using more • than one in the oven at a time. For instance, they should be used in rack positions 1, 3 and 5 or 2 and 4, counting up from the bottom, instead of positions 2, 3 and 4.

Installation:

Fully extend the two side guides. Align the two small clips 1. on the bottom at the rear of the rack with the black porcelain rack guides in the oven.

When using the GlideRack rack with Dacor’s ABS20 baking • stone, use rack position 1 for best results.

Heavier roasting pans and dishes will also cook better on • rack position 1.

Begin to slide the rack in, then lift up. The GlideRack oven 2. rack must be in between the two clips on the upper and lower side of the rack rear.

Do not leave any of the racks in the oven during self-clean. • They may be damaged and/or will become difficult to slide in and out if self-cleaned. In addition, remove the convection filter in the back of the oven before self-cleaning.

Push the rack all the way to the back. 3.

Grasp the rack in the front center and pull. The rack should 4. come forward while the side guides remain in place.

To clean the racks, use hot, soapy water and the rough side • of a sponge.

GE ECD — Oven Rack Positions diagram (page 8)
Fig. 16 · Oven Rack Positions
Page 9 of the GE ECD user manual — NOTE:
Page 9 · click to enlarge
Page 9

Oven Modes

Oven Mode Selection

All oven modes are described below:

Follow these steps to manually operate the oven in standard bake, Pure Convection or convection bake mode:

STANDARD BAKE – In standard bake mode, the bottom heating element provides conventional radiant heat. Temperatures may be set from 135˚F to 555˚F in 5˚F increments. Use standard bake for single rack baking and roasting.

Position oven rack(s) at the proper height(s). 1.

Press the 2. BAKE, PURE CONVECTION or CONVECTION BAKE key. The oven will beep once, the selected cooking mode will flash, and “– – –” will be displayed.

STANDARD BROIL – The high wattage, top heating element supplies the heat in Broil mode. The broil temperature is adjustable from 135˚F, to the “HI” setting (equivalent to 555˚F) for greater cooking flexibility. Broiling is always performed with the door closed.

Press either the 3. “+” or “–” key. The default temperature of 350˚F will be displayed.

To adjust the cooking temperature from 350˚F, press and 4. hold the TIME • TEMP key. (Press “+” key to increase the temperature setting, “–” to decrease). “PRE” and “ON” will appear in the clock display, and the oven will begin to heat. The convection fan will turn on to help stabilize the oven temperature during pre-heat. In standard bake mode, the convection fan will turn off once the desired temperature is attained. If in a convection mode, the convection fan will turn on. Also, the clock display will change from the desired cooking temperature to the actual oven temperature, starting with 135˚F. The temperature display will increase in 5˚F increments until the desired temperature is reached. The cooling fan will turn on when the oven temperature reaches 200˚F. When the desired temperature is attained, the pre-heat cycle is complete. The clock will beep once and “PRE” and “ON” will disappear from the display. (From this time forward, the “ON” display will cycle on and off with the heating elements.)

CONVECTION BROIL – The high wattage, top heating element supplies the heat in broil mode in combination with the convection fan for better heat distribution. The broil temperature is adjustable from 135˚F to the “HI” setting (equivalent to 555˚F) for greater cooking flexibility. This mode is available only on models ECD230, PCD230, and MCD230. Convection broil is always performed with the door closed.

™ – In Pure Convection mode a third heating element, encircling the convection fan located in the rear of the oven chamber, acts as the heat source. The convection fan draws air from the oven chamber, then forces it across the hot convection heating element. The heated air is directed back into the oven chamber through the convection baffle. The baffle distributes the heated air evenly to ensure uniform results. Temperatures may be set from 135˚F to 555˚F in 5˚F increments. Use this mode for single rack baking, multiple rack baking, roasting and preparation of complete meals.

PURE CONVECTION

Carefully place the food onto the desired rack(s) within the 5. pre-heated oven.

It is recommended that you set a minute timer to time the 6. cooking process (see page 11).

CONVECTION BAKE – In this combination convection- radiant mode, the lower element provides the heat. As in Pure Convection mode, the convection fan and baffle combine to circulate heated air evenly throughout the oven chamber. Temperatures may be set from 135˚F to 555˚F in 5˚F increments. Use this mode for single rack baking, multiple rack baking and roasting.

When the time expires and/or the food is done cooking, press 7. the CANCEL • SECURE key to turn off the oven.

Pre-Heating the Oven

The oven features an automatic pre-heat cycle that rapidly brings the oven chamber up to temperature. Simply by choosing a cooking mode and setting a temperature, the oven will automatically perform the pre-heat function. The pre-heat cycle operates in standard bake, Pure Convection and convection bake modes. There is no pre-heat cycle for the broil or convection broil modes.

TEMPERATURE PROBE – The temperature probe can be used in combination with standard bake, Pure Convection, or convection bake modes. The temperature probe takes the guesswork out of roasting by cooking food to the exact internal temperature you desire. The temperature range that the probe will read is from 100˚F to 200˚F.

NOTE:

SELF-CLEAN – In the pyrolytic self-clean mode, the oven reaches temperatures of 850˚F, thereby burning off oven soil automatically. The self-clean time is adjustable up to four hours so that varying degrees of oven soil can be successfully removed. Also, the self-clean cycle can be delayed to start at a later time if desired.

For faster heat up, the broil element comes on during • pre-heat. For best results, allow the oven to pre-heat prior to placing food inside.

Page 10 of the GE ECD user manual — Clock Displaying Broil (double oven)
Page 10 · click to enlarge
Page 10

What Is Pure Convection?

Wait until the shortest recommended baking time before • checking food. For baked goods, a wooden pick placed in the center should come clean when the food is done.

Your new oven has the best cooking system available today, Pure Convection. Pure Convection is a total system approach to cooking. The heat source is a third element outside the cooking cell behind a baffle. Not only does the baffle separate the food from the heat source, it channels the air from the convection fan evenly into the cell eliminating any hot or cool spots in the oven. This system is what allows multi-rack cooking while achieving even results from one rack to another.

Place pans carefully on the oven racks. Turn pans on the • racks so that the long sides run left to right, parallel to the door.

Adjustments to recipe times and temperatures need to be • made when baking at high altitudes. Consult a cookbook on high-altitude cooking.

Bakeware Tips:

The other component in Pure Convection is the filter. The filter eliminates the transference of flavors when cooking entire meals and also keeps the oven cleaner.

Cakes, quick breads, muffins and cookies should be baked in • shiny, reflective pans for light, golden crusts.

Medium gauge aluminum sheets with low sides should be • used when preparing cookies, biscuits and cream puffs.

GE ECD — Bakeware Tips: diagram (page 10)
Fig. 17 · Bakeware Tips:

Bake most frozen foods in their original foil containers placed • on a flat cookie sheet. Follow the package recommendations.

When using glass bakeware, reduce the recipe temperature • by 25˚F, except when baking pies or yeast breads. Follow the standard recipe baking time for pies and yeast breads. Multiple Rack Baking

The uniform air circulation provided by Pure Convection cooking enables the full oven capacity to be utilized. Many foods, such as pizzas, cakes, cookies, biscuits, muffins, rolls and frozen convenience foods can be successfully prepared on either two or three racks at the same time. Additionally, complete meals can be prepared by using multiple racks. See below for specific recommendations. Follow the steps in the Oven Modes section to manually operate the oven, or refer to the Delay Timed Cooking section below for automatic operation.

Heated Air Circulation in Convection Modes

Baking and Roasting Tips

Multiple Rack Baking Tips:

All modes can be used to successfully prepare meals using standard recipes or your own personal favorites.

Typically, when baking on two racks, use rack positions 2 and • 4 or 3 and 5. When baking on three racks, use rack positions 1, 3 and 5.

Because of variations in food density, surface texture and consistency, there are a few foods that may be prepared more successfully in the standard bake mode. For this reason, standard bake mode is recommended when preparing baked goods such as custard. The user may find other foods that are also prepared more consistently in standard bake mode. This is perfectly normal.

When adapting a single rack recipe to multiple rack baking, • it may be necessary to add to the baking time. This is due to the extra amount of food in the oven. Broiling

As a general rule, to convert conventional Standard Bake • recipes to convection recipes, reduce temperature by 25˚F and the cooking time by approximately 10%.

Broiling is a quick and flavorful way to prepare many foods, including steaks, chicken, chops, hamburgers and fish. Broiling in the oven is performed with the oven door completely shut. It is normal and necessary for some smoke to be present to give the food a broiled flavor. The broil temperature may be adjusted in 5˚F increments from 135˚F up to the maximum setting of “HI”. The “HI” setting is equivalent to 555˚F.

Some recipes, especially those that are homemade, may • require adjustment and testing when converting from standard to convection modes. If unsure how to convert a recipe, begin by preparing the recipe in standard bake mode. After achieving acceptable results this way, follow the convection guidelines listed. If the food is not prepared to your satisfaction during this first convection trial, adjust only one recipe variable at a time (such as cooking time, rack position or temperature) and repeat the convection test. If necessary, continue adjusting one recipe variable at a time until satisfactory results are achieved. See Common Baking Problems on the facing page for additional information.

GE ECD — Heated Air Circulation in Convection Modes diagram (page 10)
Fig. 18 · Heated Air Circulation in Convection Modes

Do not open the oven door frequently during baking. Look • through the door window to check the progress of baking whenever possible.

Clock Displaying Broil (double oven)

Use the minute timers to time baking functions (see page 11). •

Page 11 of the GE ECD user manual — IMPORTANT:
Page 11 · click to enlarge
Page 11

To operate the oven in standard broil or convection broil modes:

BROILING TIPS:

Always use a broiler pan and grill to provide drainage for 1. excess fat and grease. Doing so will reduce spatter, smoke and flare-ups.

Close the door tightly. 1.

Press the 2. BROIL or CONVECTION BROIL key.

Pre-heat the broiler for 10 minutes prior to cooking. 2.

  • Press the 3. TIME
  • TEMP + or TIME
  • TEMP – key and the default temperature setting “HI” will be displayed. “HI” is equivalent to 555˚F.

Begin with a room temperature broiler pan for even cooking. 3.

Use tongs or a spatula to turn and remove meats. Never 4. pierce meat with a fork. The natural juices will escape.

If a temperature other than 4. “HI” is desired, press the TIME • TEMP – key to reduce the temperature. Six seconds after setting the temperature, the “ON” indicator will light up in the clock display, the broiler element will begin heating.

Broil food on the first side for slightly more than half of the 5. recommended time, then season and turn. Season the second side just before removing.

Dacor recommends that you set the minute timer(s) to time 5. the broiling process (see page 11).

To prevent sticking, lightly grease the broiler grill. Excess 6. grease will result in heavy smoke. For easier cleaning, remove the broiler pan and grill when the food is removed. While the pan and grill are still warm, soak the pan and grill in a solution of hot water and dishwashing liquid, then scrub them with an abrasive pad.

When the minute timer expires and/or the food is cooked, 6. press the CANCEL • SECURE key to turn off the oven. The cooling fan will continue to run for 30 to 45 minutes depending upon the length and temperature of the broiling process.

Common Baking Problems

PROBLEMPROBABLE CAUSECORRECTION Cookies and biscuits burn on the bottom.Oven door opened too oftenUse door window to check food or set minute timer to shortest recommended time and check food when timer beeps. Incorrect rack position being used. Pan too close to bake element.Change rack position. Use Pure Convection mode. Standard bake or convection bake mode being used.Use Pure Convection mode. Cookies and biscuits are too brown on top.Rack position being used is too high.Change rack position. Food was placed in the oven during pre-heat.Wait until oven is pre-heated Cakes burn on the sides or are not done in center.Oven was too hot.Reduce temperature. Cakes crack on top.Oven temperature was too high.Reduce temperature. Cakes are not level.Oven and/or oven rack was not level.Level oven and rack as needed. Pies burn around edges or are not done in center.Oven was too hot.Reduce temperature. Dark, heat absorbing pan being used.Use shiny, reflective pans. Pies are too light in color on top.Oven was not hot enough.Increase oven temperature. Oven and/or rack over crowded.Reduce number of pans.

Delay Timed Cooking

WARNING

This function allows the user to finish and/or start a cooking cycle automatically. It is especially useful for preparing meals in advance or cooking while you are at work or play. Timed cooking can only be used with standard bake, Pure Convection and convection bake modes. Timed cooking does not function in the broil modes.

Food safety is an important consideration when using delayed cooking modes. To avoid potential sickness and spoiling of food, take the following steps:

  • Avoid using foods that will spoil while waiting for the
  • cooking cycle to begin. Typical foods to avoid include those containing eggs and dairy products, cream soups, and cooked or uncooked meats, poultry and fish. If cooking will not begin immediately, place only very cold
  • or frozen food into the oven. Most unfrozen foods should never stand in the oven for more than two hours before cooking begins. Do not allow foods to remain in the oven more than one
  • hour after completion of the cooking cycle. When the temperature drops below 140˚, bacteria can develop.

IMPORTANT:

COOK TIM • E refers to the length of the cooking cycle. It does not refer to the start time.

The time required to pre-heat the oven must be included in • the COOK TIME. Allow for about 8 to 12 minutes pre-heat time depending upon the temperature setting. The top element does not come on to pre-heat in the delay mode, so you will not pre-maturely brown foods.

Page 12 of the GE ECD user manual — Meat Probe
Page 12 · click to enlarge
Page 12

Delay Timed Cooking (Continued)

Using the Meat Probe

To begin cooking immediately and turn off at the desired time:

For many foods, especially roasts and poultry, internal food temperature is the best test for properly cooked food. The meat probe takes the guesswork out of roasting by cooking food to the exact temperature you desire.

Position oven rack(s) at the proper height(s). 1.

Place the food onto the center of the oven rack(s). 2.

Important things to know about the meat probe:

Select the desired cooking mode and temperature. 3.

Double oven models have a meat probe connector in the • upper oven only.

Press the 4. COOK TIME key and “TIME” will appear in the clock display. Press the TIME • TEMP + key to set the length of time that the food will be cooked. The cook time can be set from 5 minutes to 11 hours, 50 minutes.

If the internal temperature of the meat you are cooking is • less than 55˚F, you need to wait to insert the meat probe for proper operation.

Make sure the food is completely defrosted before inserting • the meat probe to avoid breaking the probe.

For fully defrosted meat • : allow it to come to room temperature by leaving it out for at least 15 minutes, but no more than 2 hours. Fully defrosted meat allowed to come to room temperature before cooking can improve cooking results for searing, roasting and meat cooked rare.

For partially frozen meat • : first fully defrost and follow the steps above.

Setting the Oven for Delay Timed Cooking

To avoid the possibility of burns, unplug the meat probe using • hot pads.

After the cook time has expired, the clock will beep 5. three times, and “Hold” will be displayed. If cooking in a convection mode, the convection fan will also turn off at this time. While in hold mode, the oven temperature will be maintained at 150˚F for a period of two hours. Hold mode can be cancelled by pressing the CANCEL • SECURE key. The cooling fan will continue to run depending upon the length and temperature of the cooking process.

To prevent damage, use the handles of the meat probe and • plug to insert and remove them from the food and connector. Do not use tongs to pull on the cable when removing the probe.

Never leave the meat probe inside the oven when the oven is • not in use and especially during self-clean mode.

To start at a later time and finish at the desired time:

To prevent damage to the oven, do not use probes other than • the one provided with your wall oven.

Follow steps 1 thru 4 in the previous instructions for timed 1. cooking.

Probe Placement:

Press the 2. STOP TIME key.

Lay the probe on the outside of the meat along the top or 1. side and mark with your finger where the edge of the meat comes to the probe. The point should rest in the center of the thickest meaty part of the roast.

  • “STOP” 3. will appear in the clock display. Press the TIME
  • TEMP + key to enter the time of day that you wish the oven to shut off. “DELAY” will appear on the display. The oven will calculate the correct start time. After the cook time has expired, the clock will beep three times, and “Hold” will appear on the display. If cooking in a convection mode, the convection fan will also turn off at this time. While in hold mode, the oven temperature will be maintained at 150˚F for a period of two hours. Hold mode can be cancelled by pressing the CANCEL
  • SECURE key. The cooling fan will continue to run depending upon the length and temperature of the cooking process.

Meat Probe

NOTE:

Insert the probe into the meat to the point marked by your 2. finger. The probe should not touch the bone, fat, gristle or the bottom of the pan.

For double ovens, both the upper and lower chambers can be • set for delay timed cooking. However, both chambers must have the same cook times and stop times.

For roasts with no bone, insert the probe into the side of • the roast in the center. For bone-in ham or lamb, insert the probe into the center of the lowest large muscle or joint.

Do not use foods containing baking powder or yeast in delay • timed cooking mode. These foods will not rise properly.

For dishes such as meat loaf or casseroles, insert the • probe into the center of the dish. When cooking fish, insert the probe from just above the gill into the meatiest area, parallel to the backbone.

Insert the probe into the meatiest part of the inner thigh • from below, and parallel to the leg of a whole turkey.

Show 4 more labels / short text on this page
Cable · Probe · Plug · Handles
Page 13 of the GE ECD user manual — 165˚F
Page 13 · click to enlarge
Page 13

Dehydrating/Defrosting

Setting the Oven When Using the Temperature Probe:

Pre-heat the oven to the desired temperature. 1.

The oven can be used to dehydrate or defrost foods at low heat settings in Pure Convection mode.

Insert the meat probe into the food. (See 2. Probe Placement).

After the oven cell has reached the desired temperature, 3. place the food into the oven.

Follow these steps to dehydrate or defrost foods:

Position oven rack(s) at the proper height(s). 1.

Wearing an oven mitt, lift the meat probe connector cover 4. in the oven and plug in the meat probe. The connector is located on the left inside oven wall near the front of the oven. Make sure the plug is pushed all the way in.

Place the food onto the center of the oven rack. For 2. dehydrating, prepare food as recommended then place food onto a drying rack.

Press the 3. PURE CONVECTION key.

Close the oven door. 5.

Press the 6. PROBE key. The display will flash “PRB” and beep if the probe is not connected properly.

Set the temperature to 135˚F, the minimum temperature that 4. can be set. For dehydrating, a higher temperature setting may be required. Follow the recommended temperature for the type of food being prepared.

  • Adjust the temperature to the desired setting using the 7. TIME
  • TEMPERATURE keys. A "jump-in" temperature of 160˚ will appear when the TIME
  • TEMPERATURE key is first pressed. To change to a different temperature, press the TIME
  • TEMPERATURE key repeatedly until you reach the desired temperature. The temperature can be set from 100-200˚F. See the chart below for the Minimum Safe Internal Temperatures for Various Foods .

Dacor recommends that you set the minute timer(s) to time 5. the process (see page 11). Using the Minute Timer

The clock features two timers that may be used to time cooking or other processes up to 11 hours 50 minutes in length.

After the temperature is set, the control panel temperature 8. readout will default to 95˚F, even if the food has not reached that temperature. The temperature readout will increase in 1˚F increments until the food reaches the set temperature.

To use the minute timer:

Press the key labeled 1. TIMER 1, or TIMER 2. The clock will display “00:00”, and “TIMER 1” or “TIMER 2” will flash.

The oven will go into hold mode for 2 hours after the internal 9. temperature of the food has reached the desired temperature and will hold the oven temperature at 150˚F. The residual heat of the oven will cause the internal temperature of the food to continue to climb. Use hot pads to remove the meat probe from the food.

Press the 2. + key repeatedly until the desired time is displayed on the clock.

After 3. TIMER 1 has expired, the clock will sound off with one second beeps and “TIMER 1” will appear in the display. After the TIMER 2 minute timer has expired, the clock will sound alternating one and two second beeps and “TIMER 2” will appear in the display. The beeper can be silenced by pressing the TIMER key while the beeper is sounding.

NOTES:

After meat is pulled out of the oven, it will continue to cook. • Carry-over cooking affects all foods. The larger the item, the longer the carry-over. It is best to let the meat rest after it comes out of the oven for 10 to 15 minutes. Doing so allows meat to retain its juices and continue to set, making it easier to carve.

NOTES:

If the probe is left attached to the connector when not in use, • the control panel will beep and flash "PRB" until the probe is unplugged. Unplugging the probe from the oven turns the oven off.

To view the 1. current time of day rather than the minute timer display, press the CLOCK key. To change back to a minute timer display, press the TIMER 1 or TIMER 2 key.

To cancel the minute timer while in progress, press the 2. TIMER 1 or TIMER 2 key twice. The clock display will return to the time of day.

Minimum Safe Internal Temperatures for Various Foods

Type and Cut Internal

Temp.

The minute timers may be used at the same time as delay 3. timed cooking or self-clean.

Pork, ham, sausage and bacon 180˚F

All foods previously served and cooled that are reheated

165˚F*

The minute timers will beep for 2 minutes (if not cancelled) 4. before automatically shutting off.

All poultry and game birds (turkey, chicken, cornish game hen, duck, etc.)

180˚F

Pressing the 5. CANCEL • SECURE key when the beeper is sounding will cancel both the beeper and the cooking function.

Fish and most other potentially hazardous food not listed in this table

165˚F

Beef steaks (rare) 145˚F

Beef roasts (rare) 145˚F

* Within two hours

Stuffed meats 165˚F · Stuffing 165˚F

Page 14 of the GE ECD user manual — Convection Filter Removal
Page 14 · click to enlarge
Page 14

C are and C leaning

Porcelain Surfaces

WARNING

  • To avoid electrical shock or burns, turn off all controls and
  • ensure the oven is cool before cleaning. Do not use harsh or abrasive cleaning agents, waxes,
  • polishes or commercial oven cleaners to clean the oven. Do not use commercial oven cleaners inside the oven. Use
  • of these cleaners can produce hazardous fumes or can permanently damage the porcelain finishes.

The oven interior and inner door liners are finished in • porcelain enamel. Clean these surfaces with a solution of mild detergent and hot water. Rinse and dry with a soft cloth. Do not use abrasives or commercial oven cleaners. Always remove excess grease and soil from the oven interior and door prior to using the self-cleaning cycle. Brass, Chrome and Copper Surfaces

Read and follow these Care and Cleaning instructions completely to maintain proper oven operation and appearance throughout the life of the product. Several materials and finishes are used in the oven. Each material and finish must be properly cleaned according to the following recommendations. Failure to follow these recommendations may result in permanent damage to the oven. Control Panel

Clean these surfaces with a solution of mild detergent and • warm water. Rinse, dry and polish with a soft, lint-free cloth.

Brass, chrome, and copper finishes are protected with a clear • coat enamel and should not be cleaned with metal polishes. Broiler Pan and Grill

  • To avoid accidentally turning the oven on while cleaning the
  • control panel, activate the secure feature. Press and hold the CANCEL
  • SECURE key for approximately three seconds. This will disable the control panel and allow cleaning the controls without accidentally starting any functions. “OFF” will appear in the display when the control panel has been secured.

The oven broiler pan and grill are finished in porcelain • enamel. Clean both components in a solution of detergent and hot water. For heavy soil conditions, use a scouring pad such as steel wool with plenty of water. Rinse well after cleaning. Oven Racks

  • To re-activate the control panel, again push and hold the
  • CANCEL
  • SECURE key for three seconds. “OFF” will disappear from the display.

The oven racks are chrome-plated. For everyday cleaning, • apply a solution of detergent and hot water. To clean heavy soil, use a scouring pad such as steel wool with plenty of water, or use a solution of 1 cup ammonia to 2 gallons of water. Remove the racks during self-cleaning. If the racks are left in the oven during self-cleaning, they will permanently discolor. Convection Filter

Clean the control panel with a solution of mild detergent • and warm water. DO NOT USE ABRASIVE CLEANERS OR SCRUBBERS. THEY WILL PERMANENTLY DAMAGE THE FINISH. Dry the control panel completely with a soft, lint-free cloth. Door Handle/Control Housing

Clean the door handle and control panel housing with a • solution of mild detergent and hot water. Rinse and dry with a soft cloth. DO NOT USE ABRASIVE CLEANERS OR SCRUBBERS. THEY WILL PERMANENTLY DAMAGE THE FINISH. Door Glass

WARNING

  • Remove the filter only when it is cool.
  • Remove the filter during self-cleaning. If the filter is left in
  • the oven during self-cleaning it will permanently discolor. Re-install the filter before cooking in the oven again. Failure to do so will expose the convection fan blade that rotates at high speed during convection modes.

Clean all glass surfaces with a solution of mild detergent and • hot water. Use a mild glass cleaner to remove fingerprints or smears. Dry completely with a soft, lint-free cloth. Stainless Steel Surfaces

The convection filter is made of stainless steel. Remove the • filter regularly for cleaning. A clogged filter will reduce the effectiveness of the convection cooking modes.

On stainless steel ovens, the control panel, door(s) and • exhaust grill are covered with stainless steel panels. Clean these surfaces with a solution of mild detergent and warm water. Rinse and dry with a soft, lint-free cloth.

IMPORTANT:

If commercially available stainless steel cleaners are used, • it is important to read the labels for chlorine compounds. Chlorine is a corrosive substance. If these compounds are present, rinse thoroughly and dry with a soft, lint-free cloth.

Always wipe stainless steel surfaces with the grain. •

Convection Filter Removal

Page 15 of the GE ECD user manual — Display - Self-Cleaning Mode
Page 15 · click to enlarge
Page 15

C are and C leaning

Soak the filter in hot soapy water. •

Remove the broiler pan and grill, all cookware, utensils and 2. other loose items from the oven chamber. Also, remove all oven racks and the convection fan filter to prevent them from permanently discoloring. However, to clean stubborn particles in the convection filter you may elect to simply leave it in place during self-clean. The filter will discolor due to the high heat, but the filtering capabilities will not be affected.

Dry the filter completely before re-installing. •

To re-install the filter, orient the two mounting tabs towards • the rear, open end down. Hook the two mounting tabs over the center horizontal bar.

GE ECD — C are and C leaning diagram (page 15)
Fig. 19 · C are and C leaning

Wipe up excess grease and other food spills with a damp 3. cloth. This will minimize smoke and increase the efficiency of the self-clean cycle.

Turn on kitchen fans or vents to help remove odors during the 4. process.

IMPORTANT:

If racks are left in the oven during a self-clean cycle, it will affect their ability to slide in and out easily. If damage occurs, polish the rack edges with a soapy steel wool pad, then apply a small amount of vegetable oil to the edges so that the racks will slide more easily.

To Start the Self-Clean Cycle:

Convection Filter Installation

Close the oven door completely. 1.

Press the 2. SELF-CLEAN key. The oven will beep once, “CLEAN” will flash, and “– –:– –” will be displayed.

Self-Cleaning

GE ECD — Self-Cleaning diagram (page 15)
Fig. 20 · Self-Cleaning

Press the 3. TIME • TEMP + key and the default time of “2:00” hours will be displayed.

1. DO NOT OPERATE THE OVEN LIGHTS IN THE SELF-CLEAN MODE. 2. Do not touch the outside surfaces of the oven during the self-clean cycle.

Increase the self-clean time up to 4 hours (depending upon 4. the amount of oven soil) by holding the TIME • TEMP + key.

To delay the self-clean start to a more convenient time, press 5. the STOP TIME key. Then, press the TIME • TEMP + key to set the time of day for the cycle to be complete. “DELAY TIMED” will appear in the clock display. The cycle can be delayed up to 11 hours and 50 minutes.

The oven features an automatic pyrolytic self-cleaning cycle to eliminate the need for difficult and time-consuming manual scrubbing of interior surfaces. During this cycle, the oven reaches temperatures of 850˚F to burn off soil and deposits. A powder ash residue is left in the bottom of the oven after completion of the self-clean cycle.

Approximately 30 to 60 seconds after selecting self-clean, the 6. automatic door latch will lock the door. “LOCK” and “ON” will appear in the clock display. The oven will begin heating. The “ON” indicator will cycle on and off with the burner.

The self-clean time is variable from 2 to 4 hours to offer flexibility in handling various soil conditions. A 2-hour cycle normally handles a moderately soiled oven, whereas a 4-hour cycle is recommended for heavy soil. The self-clean cycle can also be delayed to start at a later time if desired.

NOTE:

If delay timed mode has been set, the “ON” display and the oven heat will not turn on until the programmed time has been reached.

IMPORTANT:

IMPORTANT:

It is normal for some smoke to be emitted during the first few • self-clean cycles.

  • The electric door latch is a convenient safety feature that keeps the door locked when the interior is too hot. If the door is not closed completely, the automatic door latch will not lock the door when the self-clean is selected. In this case, “Door” will flash in the display, Press the CANCEL
  • SECURE key and wait about 1 minute. Repeat the self-clean steps from the beginning, being certain to close the door completely. Do not try to force the door open after it is locked, because damage can occur. If you need to unlock the door, press the CANCEL
  • SECURE key to turn off the self-clean cycle. After about 1 minute, “LOCK” will disappear from the clock display, and the door will unlock. The door will remain locked until the oven temperature falls below 390˚F.

Popping sounds are normal during self-clean. These sounds • are caused by the expansion and contraction of metal surfaces during heat-up and cool-down.

Do not line the oven with aluminum foil or other materials. • These items can melt or burn during a self-clean cycle, causing permanent damage to the oven.

Display - Self-Cleaning Mode

To Prepare the Oven for Self-Cleaning:

Clean soil from the oven front frame area and the oven door 1. outside of the door gasket. Do not clean the door gasket. Cleaning the door gasket by hand can cause it to bend or move. A tight door seal is essential for proper baking and self-cleaning. Rinse surfaces well with a solution of vinegar and water, then wipe dry. Heavily soiled areas may be cleaned with a non-scratching scouring pad.

Continued...

Page 16 of the GE ECD user manual — NOTE:
Page 16 · click to enlarge
Page 16

C are and C leaning

Self-Cleaning (Continued)

Adjusting the Oven Temperature

About 50 to 60 minutes is required for the oven to reach the 7. self-clean temperature of 850˚F.

IMPORTANT:

You may find the temperature in their new oven to be different from that of their previously-owned appliance. Familiarity with the old appliance sometimes makes it difficult to get used to a new oven. If you feel that the oven temperature is consistently high or low, the temperature of the new oven can be calibrated. The calibration needs to be done only once.

The self-clean cycle can be stopped at any time by pressing 8. CANCEL • SECURE.

After completion of the self-clean cycle, the oven will stop 9. heating and the “ON” and “CLEAN” indicators will disappear from the clock display. Press the CANCEL • SECURE key.

After the interior oven temperature falls below 390˚F, the door 10. latch will release and “LOCK” will disappear from the display. The door can be opened. Do not select any cooking function until the oven door is unlocked.

To calibrate the oven temperature:

Press the 1. BAKE key.

Press the 2. TIME • TEMP + pad to set a temperature of 500˚F or higher.

Open the door. After ensuring that the oven has cooled 11. sufficiently to be safe, use a damp cloth or sponge to wipe out the powder residue found in the bottom of the oven. If white spots remain in the oven, remove them with a non-scratch scouring pad before using the oven again. These spots are normally salt that cannot be removed by the self-clean cycle.

Press and hold the 3. BAKE key. After approximately 5 seconds the temperature display is replaced by “00”. The BAKE key can be released. The calibration mode has been accessed.

Re-install the oven racks and convection filter before cooking 12. in the oven.

Self-Cleaning Tips:

If any soil remains in the oven after completion of a self-clean • cycle, repeat the cycle if desired. Increase the cleaning time during future cycles.

TIMER 1 CLOCK STOP TIME TIMER 2

Display When Calibrating the Oven

Clean the oven regularly to prevent excessive soil build-up. • Doing so will increase the efficiency of the self-clean cycle and reduce the amount of smoke and odors generated.

  • Press the 4. TIME
  • TEMP + or TIME
  • TEMP – key to set the amount of temperature adjustment. The temperature can be changed a maximum of 35˚F higher or lower. Set the adjustment to positive (+) numbers to increase the oven temperature; set the adjustment to negative (–) numbers to reduce the oven temperature. Temperatures can be adjusted in increments of 5˚F.

Self-clean in the cooler evening hours after cooking is • complete and when electricity rates are lower.

On double oven models, if one oven is in the self-clean mode • the other oven is inoperable.

After setting the desired temperature adjustment, press the 5. CANCEL • SECURE key to exit the calibration mode and to reset the clock display.

NOTE:

If the 1. CANCEL • SECURE key is not pressed after setting the adjustment, the clock display will automatically reset in 6 seconds.

The amount of temperature adjustment may be changed 2. again by repeating the calibration procedure. The oven will only retain the most recent temperature adjustment.

The temperature adjustment is not affected by an electrical 3. power failure

The temperature adjustment only affects standard bake and 4. convection bake modes. Broil and self-clean temperatures cannot be adjusted.

Page 17 of the GE ECD user manual — Oven Light Assembly
Page 17 · click to enlarge
Page 17

C are and C leaning

Replacing the Oven Light

Accessories

WARNING

For accessories call your local Dacor dealer or visit www.everythingdacor.com

To prevent electrical shock and/or personal injury:

Accessory Cookie sheets (3 in a carton): These Full sized cookie sheets maximize oven rack baking capabilities by allowing the total usable rack area.

  • Make certain that the appliance and light bulb are cool and
  • that power to the appliance has been turned off before replacing the light bulb. Always ensure that the lens cover is in place when using
  • the appliance. The lens cover protects the bulb from breakage caused by high temperatures or mechanical shock.

27” Oven - Model No. ACS273 •

30” Oven - Model No. ACS303 •

36” Oven - Model No. ACS363 •

Replacement Oven Light Bulb

The light assembly consists of a removable lens cover and 10-watt 12 Vac halogen bulb, as well as a light fixture housing. Light bulb replacement is considered to be a homeowner maintenance operation.

Part No. 86364 •

Stainless Steel Cleaner

Part No. A302 •

To replace a light bulb, follow these steps:

Turn off the power at the main power supply. 1.

Remove the lens cover from the housing by pulling straight 2. out.

NOTE:

In some cases the lens cover may be tightly in place and require removal using the included lens pry stick. The pry stick should be used with caution. Do not cause uneven stress on the lens cover. Gently insert the pointed end of the pry stick under the center edge of the lens cover on the side facing the oven door. Hold your hand under the lens for support then pry out to remove the lens cover.

Pull the light bulb out and replace it with a special 10-watt 3. halogen bulb rated for use in a self-cleaning oven. Use Dacor Part No. 86364 available from any authorized Dacor parts distributor or dealer.

Reinstall the lens cover by aligning the cover over the 4. opening and gently pressing it into its original position. IMPORTANT: Make sure the cutout in the lens is lined up with the socket to prevent damage to the light fixture.

Turn the power back on at the main power supply. 5.

Oven Light Assembly

Light Socket

Page 18 of the GE ECD user manual — PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
Page 18 · click to enlarge
Page 18

B efore Y ou C all F or S ervice

Problem Solution Guide

Unnecessary service calls may be expensive, frustrating and time-consuming. Before you call for service, please review the potential problems, possible causes and remedies shown below. Also, see the facing page for various oven failure codes that can be displayed on the control panel. Failure codes will appear where the temperature is normally displayed on the control panel.

PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION

Nothing works. Oven is not connected to electrical power. Have oven connected to a properly sized electrical power supply by a qualified electrician.

Power supply is not energized. Check for tripped circuit breaker or blown fuse. Have an electrician check power supply.

Oven will not heat. Oven settings are not correct. Follow mode selection and clock settings as specified in OVEN OPERATION section.

Oven is set for delay-timed cooking. Oven will turn on automatically at time set. If desired, press CANCEL • SECURE key to cancel out of delay timed cooking.

  • Clock displays incorrect time of day. Time of day is not set. Press CLOCK touch pad, then press TIME
  • TEMP + or TIME
  • TEMP - key to set correct time of day.

Power supply has been interrupted. Reset time of day.

Foods over-cook. Incorrect cooking time, temperature or rack position being used.

Adjust temperature or time settings.

Oven temperature calibration differs from your previous oven.

Calibrate temperature according to Adjusting the Oven Temperature section (see Care and Cleaning).

Foods under-cook. Incorrect cooking time, temperature or rack position being used.

Adjust temperature or time settings.

Oven temperature calibration differs from your previous oven.

Calibrate temperature according to Adjusting the Oven Temperature section (see Care and Cleaning).

Oven does not self-clean. Door is not shut tight so automatic door latch will not lock.

Close door tightly.

Oven settings are not correct. Follow mode selection and clock settings as specified in the Self-Cleaning section (see Care and Cleaning).

Oven is set for delay timed cleaning. Oven will turn on automatically at time set. If desired, press CANCEL • SECURE key to cancel out delay-timed cleaning.

Oven light will not work. Light bulb is burned out. Follow Replacing the Oven Light section (see Care and Cleaning).

Door will not open. Oven is in self-clean mode. If oven is hot, door latch will release automatically when oven temperature falls below 390˚F at end of cycle.

If SELF-CLEAN was just selected and the oven is still cool, press CANCEL • SECURE key to turn off self-clean. The door will open in about 30 seconds.

Oven is set to self-clean in delay-timed mode.

Oven will turn on automatically at time set. If desired, press CANCEL • SECURE key to cancel out of delay-timed mode.

Page 19 of the GE ECD user manual — Oven Failure Codes
Page 19 · click to enlarge
Page 19

B efore Y ou C all F or S ervice

IMPORTANT:

If a failure code is displayed, the oven will beep continuously until the user presses the CANCEL • SECURE key. The oven will not heat after a failure code is displayed. Call a qualified appliance technician to repair the oven.

F0. Touch pad is stuck in depressed position.

F1. Relay circuit failure.

F2. Oven temperature exceeded the clean runaway temperature (self-clean mode only) or the cooking runaway temperature (cooking modes only).

F3. Short circuit in the oven temperature sensor.

F4. Open circuit in the oven temperature sensor.

F6. Failure in the EEPROM check comparison. (Only time of day and timer will operate.)

F7 Failure of the self-clean automatic door latch circuit.

F8. Failure of the door latch motor. Occurs when the motor runs for two minutes without the door locking in self-clean mode.

Oven Failure Codes

Clock Display Cause

Page 20 of the GE ECD user manual — LIMITED FIRST YEAR WARRANTY
Page 20 · click to enlarge
Page 20

S ervice and P roduct W arranty

Product Maintenance

What Is Not Covered

No maintenance, other than that in the CARE AND CLEANING section of this use and care manual, should be attempted by the owner/operator. All other maintenance and service must be performed by a qualified appliance technician. If You Need Service...

Failure of the product caused by faulty installation, improper • usage, or neglect of required maintenance.

Service calls to educate the customer in the proper use and • care of the product.

Failure of the product when used for commercial, business, • rental or any application other than for residential consumer use.

First, review the recommended checks listed in the preceding Before You Call for Service section. Then, be certain that the appliance has been installed properly and is being operated correctly. Familiarize yourself with the warranty terms and conditions listed in this section.

Replacement of house fuses or fuse boxes, or resetting of • circuit breakers.

Damage to the product caused by accident, fire, flood or • other acts of God.

If the above mentioned checks have been completed and the problem has not yet been remedied, call your local authorized DACOR service representative. Your dealer can normally provide the name and telephone number of the nearest service company.

Breakage, discoloration or damage to glass, metal surfaces, • plastic components, trim, paint, porcelain or other cosmetic finish, caused by improper usage or care, abuse, or neglect.

THE REMEDIES PROVIDED FOR THE ABOVE EXPRESS WARRANTIES ARE THE SOLE AND EXCLUSIVE REMEDIES. THEREFORE, NO OTHER EXPRESS WARRANTIES ARE MADE, AND OUTSIDE THE FIFTY STATES OF THE UNITED STATES AND THE DISTRICT OF COLUMBIA, ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. IN NO EVENT SHALL DACOR® BE LIABLE FOR INCIDENTAL EXPENSE OR CONSEQUENTIAL DAMAGES. NO WARRANTIES, EXPRESSED OR IMPLIED, ARE MADE TO ANY BUYER FOR RESALE.

DACOR works diligently to ensure your satisfaction when service is necessary. However, if you are not completely satisfied with the service provided, contact the company that performed the service and express why you are not pleased. Normally, they will be willing and able to resolve the problem.

If the service agency is not able to respond effectively, call or write the DACOR Customer Service Department. The phone number and address of this department are listed on the inside front cover of this manual. Please include your telephone number if you choose to write. We will then do our utmost to assure your happiness and satisfaction. What Is Covered

Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

CERTIFICATE OF WARRANTIES

DACOR WALL OVENS

WITHIN THE FIFTY STATES OF THE U.S.A., THE DISTRICT OF COLUMBIA AND CANADA*:

FULL ONE YEAR WARRANTY

If your DACOR product fails to function within one year of the original date of purchase, due to a defect in material or workmanship, DACOR will remedy the defect without charge to you or subsequent users. The owner must provide proof of purchase upon request and have the appliance accessible for service.

* Warranty is null and void if non-CSA approved product is transported from the U.S.

OUTSIDE THE FIFTY STATES OF THE U.S.A., THE DISTRICT OF COLUMBIA AND CANADA:

LIMITED FIRST YEAR WARRANTY

If your DACOR product fails to function within one year of the original date of purchase, due to a defect in material or workmanship, DACOR will furnish a new part, F.O.B. factory, to replace the defective part. All delivery, installation and labor costs are the responsibility of the purchaser. The owner must provide proof of purchase upon request and have the appliance accessible for service.

Page 21 of the GE ECD user manual — N otes
Page 21 · click to enlarge
Page 21

N otes

Page 22 of the GE ECD user manual — N otes
Page 22 · click to enlarge
Page 22

N otes

Page 23 of the GE ECD user manual — NO POSTAGE
Page 23 · click to enlarge
Page 23

NO POSTAGE

NECESSARY

IF MAILED

IN THE UNITED STATES

BUSINESS REPLY MAIL

FIRST-CLASS MAIL DIAMOND BAR CA

PERMIT NO. 4507

POSTAGE WILL BE PAID BY ADDRESSEE

DACOR INC. ATTN: WARRANTY PROCESSING DEPT 1440 BRIDGE GATE DR STE 200 PO BOX 6532 DIAMOND BAR CA 91765-9861

fold here

Page 24 of the GE ECD user manual — WARRANTY INFORMATION
Page 24 · click to enlarge
Page 24

Please visit www.Dacor.com to activate your warranty online.

WARRANTY INFORMATION

Please rest assured that under no conditions will Dacor sell your name or any of the information on this form for mailing list purposes. We are very grateful that you have chosen Dacor products for your home and do not consider the sale of such information to be a proper way of expressing our gratitude!

cut here cut here

Owner’s Name:

(Please Print or Type) Last First Middle

Street:

CityState: Zip:
Purchase DateEmail: Telephone:

Dealer:

CityState: Zip:

Your willingness to take a few seconds to fill in the section below will be sincerely appreciated. Thank you.

1. How were you first exposed to Dacor products? (Please check one only.) A. T.V. Cooking Show F Builder B. Magazine G. Architect/Designer C. Appliance Dealer Showroom H. Another Dacor Owner D. Kitchen Dealer Showroom I. Model Home E. Home Show J. Other
2. Where did you buy your Dacor appliances? A. Appliance Dealer D. Builder B. Kitchen Dealer E. Other C. Builder Supplier
3. For what purpose was the product purchased? A. Replacement only C. New Home B. Part of a Remodel D. Other
4. What is your household income? A. Under $75,000 D. $150,000 – $200,000 B. $75,000 – $100,000 E. $200,000 – $250,000 C. $100,000 – $150,000 F. Over $250,000
5. What other brands of appliances do you have in your kitchen? A. Cooktop C. Dishwasher B. Oven D. Refrigerator
6. Would you buy or recommend another Dacor product? Yes No Comments:

Thank you very much for your assistance. The information you have provided will be extremely valuable in helping us plan for the future and giving you the support you deserve.

Place Serial Number Label Here

Web sitewww.Dacor.com Corporate phone: (800) 793-0093
Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Cookies and biscuits burn on the bottom.Oven door opened too oftenUse door window to check food or set minute timer to shortest recommended time and check food when timer beeps. p.11
Cookies and biscuits burn on the bottom.Incorrect rack position being used. Pan too close to bake element.Change rack position. Use Pure Convection mode. p.11
Cookies and biscuits burn on the bottom.Standard bake or convection bake mode being used.Use Pure Convection mode. p.11
Cookies and biscuits are too brown on top.Rack position being used is too high.Change rack position. p.11
Cookies and biscuits are too brown on top.Food was placed in the oven during pre-heat.Wait until oven is pre-heated p.11
Cakes burn on the sides or are not done in center.Oven was too hot.Reduce temperature. p.11
Cakes crack on top.Oven temperature was too high.Reduce temperature. p.11
Cakes are not level.Oven and/or oven rack was not level.Level oven and rack as needed. p.11
Pies burn around edges or are not done in center.Oven was too hot.Reduce temperature. p.11
Pies burn around edges or are not done in center.Dark, heat absorbing pan being used.Use shiny, reflective pans. p.11
Pies are too light in color on top.Oven was not hot enough.Increase oven temperature. p.11
Pies are too light in color on top.Oven and/or rack over crowded.Reduce number of pans. p.11
Nothing works.Oven is not connected to electrical power.Have oven connected to a properly sized electrical power supply by a qualified electrician. p.18
Nothing works.Power supply is not energized.Check for tripped circuit breaker or blown fuse. Have an electrician check power supply. p.18
Oven will not heat.Oven settings are not correct.Follow mode selection and clock settings as specified in OVEN OPERATION section. p.18
Oven will not heat.Oven is set for delay-timed cooking.Oven will turn on automatically at time set. If desired, press CANCEL • SECURE key to cancel out of delay timed cooking. p.18
Clock displays incorrect time of day.Time of day is not set.Press CLOCK touch pad, then press TIME • TEMP + or TIME • TEMP - key to set correct time of day. p.18
Clock displays incorrect time of day.Power supply has been interrupted.Reset time of day. p.18
Foods over-cook.Incorrect cooking time, temperature or rack position being used.Adjust temperature or time settings. p.18
Foods over-cook.Oven temperature calibration differs from your previous oven.Calibrate temperature according to Adjusting the Oven Temperature section (see Care and Cleaning). p.18
Foods under-cook.Incorrect cooking time, temperature or rack position being used.Adjust temperature or time settings. p.18
Foods under-cook.Oven temperature calibration differs from your previous oven.Calibrate temperature according to Adjusting the Oven Temperature section (see Care and Cleaning). p.18
Oven does not self-clean.Door is not shut tight so automatic door latch will not lock.Close door tightly. p.18
Oven does not self-clean.Oven settings are not correct.Follow mode selection and clock settings as specified in the Self-Cleaning section (see Care and Cleaning). p.18
Oven does not self-clean.Oven is set for delay timed cleaning.Oven will turn on automatically at time set. If desired, press CANCEL • SECURE key to cancel out delay-timed cleaning. p.18
Oven light will not work.Light bulb is burned out.Follow Replacing the Oven Light section (see Care and Cleaning). p.18
Door will not open.Oven is in self-clean mode.If oven is hot, door latch will release automatically when oven temperature falls below 390˚F at end of cycle. p.18
Door will not open.If SELF-CLEAN was just selected and the oven is still cool, press CANCEL • SECURE key to turn off self-clean. The door will open in about 30 seconds. p.18
Door will not open.Oven is set to self-clean in delay-timed mode.Oven will turn on automatically at time set. If desired, press CANCEL • SECURE key to cancel out of delay-timed mode. p.18

Ask about the GE ECD

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the GE ECD

Be the first to ask — other owners or our team will answer.

Original document

GE ECD manual PDF

24 pages·2.1 MB·Oven·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…