
Z-Wave® Certified Wireless Lighting Control On/Off Relay Switch and 3-Way Switch Kit
©2009 Jasco Made in China
45609/45614

Z-Wave® Certified Wireless Lighting Control On/Off Relay Switch and 3-Way Switch Kit
Introduction Thank you for your purchase of a GE Z-Wave® control device. Z-Wave technology is designed to automate lighting/home control and provide easy remote operation of all your Z-Wave enabled de- vices. The GE Z-Wave product family includes a variety of devices to control lighting in your home. It is up to you whether you want to control one room or your entire house and whether you want to do it all now or start with one room and add more over time. This switch is one component of a Z-Wave® control system and is designed to work with all other Z-Wave enabled devices in a home control network. It will also act as a wireless repeater to insure that commands intended for another device in the network are received, thereby extending the range of the wireless control- ler. Z-Wave devices of other types and brands can be added to the system and will also act as range extenders if they support this function of repeating the signal received to other nodes in the system.
This switch is designed for use only with permanently installed fixtures. The device controlled by this Z-Wave switch must not exceed 600 watts (Incandescent); 15 Amps, 1800W (Resistive); or ½ HP (Motor).
NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT Z-Wave enabled devices should never be used to supply power to or control the On/Off status of medical and/or life support equipment!
There are no user serviceable parts in this unit.

Controlling Appliances:
Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different room than the controlled appliance, also an uninten- tional activation may occur if the wrong button on the remote is pressed. Z-Wave devices may automatically be powered on due to timed event programming. Depending upon the ap- pliance, these unattended or unintentional operations could possibly result in a hazardous condition. For these reasons, we recommend the following: 1. Assign Z-Wave controlled appliances to device numbers 10 – 18 on the GE remote. The likelihood of unintentionally turn- ing on the appliance will be reduced significantly because the “Shift” button will need to be pressed before pressing device numbers 10-18. 2. Z-Wave devices controlling appliances should be removed from “All” control setting. Instructions on how to do this are included in the manual for your GE remote. 3. Do Not include Z-Wave devices in Groups or Scenes if they control appliances. 4. Do Not use Z-Wave devices to control electric heaters or any other appliances which may present a hazardous condition due to unattended or unintentional or automatic power on control. 5. Double check programs for accuracy before using them.
WIRELESS RANGE This device complies with the Z-Wave standard of open-air, line of sight transmission distances of 65 feet. Actual performance in a home depends on the number of walls between the remote controller and the destination device, the type of construction and the number of Z-Wave enabled devices installed in the control net- work. Most Z-Wave devices act as signal repeaters and multiple devices result in more possible transmission routes which helps eliminate “RF dead-spots”.

Effects of Home Construction on Wireless Range Between Z-Wave Enabled Devices Note: The distances shown in the table below are typical examples. Actual performance in your home will vary.
* For Plug-in Modules or In-Wall Devices Installed in Plastic Junction Boxes
** Line of Sight / no obstructions
Please Note: Z-Wave home control networks are designed to work properly alongside 802.11 wireless computer networks, Bluetooth and other 2.4GHz or 5.8GHz devices. Some baby cams, wireless video devices and older cordless phones using the 900MHz frequency range may cause interference and limit Z-Wave functionality. Many 900MHz products have a switch to select channel “A” or “B”. You may find that one of these channels will cause less interference than the other.
IMPORTANT NOTE ABOUT 3-WAY CIRCUITS The term “3-way circuit” refers to a circuit with two switches and one load (light) like you find at the top and bottom of a stairway. There are many ways to physically wire a 3-way circuit and it is important to understand how the circuit you wish to upgrade to Z-Wave control is wired. Below is a description of a typical 3-way circuit.

One of the ways to wire a two-switch/one-load circuit is to route the incoming power through the first switch, then to the second switch and then to the load. Although very common and by no means a standard, it is the easiest to convert to Z-Wave control. With this type of circuit, Switch 1 is replaced by the Z-Wave auxiliary switch and Switch 2 is replaced with the primary Z-Wave switch. The auxil- iary switch does not actually control the power; instead, it sends a momentary voltage signal through the traveler wire to the primary switch which in turn, controls the power to the load.
Typical 3-way circuit:
Switch 1 Switch 2
Please consult an electrician if you have trouble identifying the type of wiring circuit you wish to convert or if you do not feel confident in your ability to convert the circuit to Z-Wave control.
INSTALLATION This switch may be used in new installations or to replace an existing wall switch. It may be used by itself for 2-way control (one switch & one load), with one 45610 Auxiliary Switch for 3-way con- trol (two switches & one load) or with two 45610 Auxiliary switches for 4-way control (three switches & one load). When used by itself for 2-way control, please make sure that the screw terminal for the traveler wire is insulated (Do Not Remove the tape over the terminal if you are not using the traveler connection).
Single Switch Wiring Schematic

3-Way Wiring Schematic using one 45609 and one 45610
Traveler - Colored (Not Green)
4-Way Wiring Schematic using one 45609 and two 45610’s
Traveler - Colored (Not Green)
Traveler - Colored (Not Green)
Red - Traveler White - Neutral

Black – Load (to light fixture)
Black – Line / Hot (from breaker)

Single, Dual and Triple Gang Boxes When installing the 45609 in multiple gang boxes it may be necessary to break off one or both of the scored tabs on the front yoke. This does not affect the electrical rating of the 45609.
Break at this line
1. Shut off power to the circuit at fuse box or circuit breaker. 2. Remove wall plate. ! Warning: Verify power is OFF to switch box before continuing. 3. Remove the switch mounting screws. 4. Carefully remove the switch from the switch box. DO NOT disconnect the wires. 5. There are five screw terminals on the 45609 switch; these are marked LINE (Hot), Neutral, LOAD, GROUND and TRAVELER. The Traveler terminal is only used for 3-way or 4-way wiring and should remain insulated if the 45609 is being installed in a 2-way system (one switch & one load). Match these screw terminals to the wires connected to the existing switch. (Do Not remove the tape over the terminal if you are not using the traveler connection). 6. Disconnect the wires from the existing switch. 7. Connect the green or bare copper ground wire to the GROUND terminal. 8. Connect the black wire that goes to the light to the terminal marked LOAD. 9. Connect the black wire that comes from the electrical service panel (Hot) to the terminal marked LINE. 10. Connect the white wire to the neutral terminal.
Tabs Tabs

11. OPTIONAL for 3 or 4-way control): Connect the Traveler wire (usually Red) to the screw terminal marked TRAVELER. The other end of this Traveler wire connects to the TRAVELER screw terminal on the 45610 Auxiliary Switch. See the following section for information about wiring the 45610 Auxiliary Switch. 12. Insert Z-Wave Switch into the switch box being careful not to pinch or crush wires. 13. Secure the switch to the box using the supplied screws. 14. Mount the wall plate. 15. Reapply power to the circuit at fuse box or circuit breaker and test the system.
Optional for 3 or 4-Way Control: 1. The 45610 requires the following 3 wiring connections: a. The Traveler wire. This is used to send voltage signals to the
primary Z-Wave switch. The signals tell the Z-wave switch what action to perform. b. Ground. c. Neutral. 2. DO NOT connect the 45610 auxiliary switch to the home’s black Hot (Line) wire.
Observe Important Wiring Information Important: This switch is rated for and intended to only be used with copper wire. The home’s electrical wires may be attached to the screw termi- nals or inserted into the holes in the back of the switch enclosure and clamped in place by tightening the screw terminals. Always follow the recommended wire strip lengths when making wiring connections.

diagram. It can then be added to groups and/or lighting scenes and managed remotely to control the On/Off status of the connected lighting.
Air Gap Switch The 45609 has an air gap switch on the lower left side (see diagram for location) to completely disconnect power to the load. Pull the air gap switch OUT to disconnect the power while replacing light bulbs and push it all the way back in for normal operation. The air gap switch must be all the way in for the switch to function and control the lighting.
BASIC OPERATION Remote Control GE Z-Wave remotes provide control of an Individual device, Groups of devices and Scenes. Other brands of Z-Wave Certified remotes may not offer as much flexibility in how you can set up your lighting control network. Please refer to your remote control’s instructions for details on its capabilities and instructions for add- ing and controlling devices.

Please Note: After a power failure, the 45609 switch returns to the last used state.
ADVANCED OPERATION The following Advanced Operation parameters require that you have an advanced controller like the GE model 45601 LCD remote. Advanced remotes from other manufacturers may also be able to change these settings; however, basic remotes do not have this capability.
All On/All Off Depending upon your primary controller, the 45609 switch can be set to respond to ALL ON and ALL OFF commands in up to four different ways. Some controllers may not be able to change the response from its default setting. Please refer to your controller’s instructions for information on whether or not it supports the con- figuration function and if so, how to change this setting.
The four possible responses are: It will respond to ALL ON and the ALL OFF command (default). It will not respond to ALL ON or ALL OFF commands. It will respond to the ALL OFF command but will not respond to the ALL ON command. It will respond to the ALL ON command but will not respond to the ALL OFF command.

Restoring Factory Defaults All Configuration Parameters can all be restored to their factory default settings by using your primary controller to delete/reset the device.
Interoperability with Z-Wave™ Devices A Z-Wave™ network can integrate devices of various classes, and these devices can be made by different manufacturers. Although every Z-Wave certified product is designed to work with all other Z-Wave certified products, your controller must include the appropriate device classifications in order to control non-light- ing Z-wave devices. As an example, the GE 45600 basic remote is designed only for controlling Z-Wave devices using the lighting control classification. The GE 45601 deluxe remote with LCD read- out can control other Z-Wave certified devices like thermostats as well as lighting.
WARRANTY JASCO Products warrants this product to be free from manufac- turing defects for a period of two years from the original date of consumer purchase. This warranty is limited to the repair or replace- ment of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state. Please contact Customer Service at 800-654-8483 (option 4) between 7:30AM – 5:00PM CST or via our website (www.jascoproducts.com) if the unit should prove defective within the warranty period: JASCO Products Company Building B, 10 E Memorial Rd. Oklahoma City, OK 73114

Compliance with IC Rules and Regulations IC: 6924A-45609 Jasco Products Company Model: 45609 This Class B digital device complies with Canadian ICES-003.

SPECIFICATIONS ZW4001 Power: 120 VAC, 60 Hz. Signal (Frequency): 908.42 MHz. Maximum Loads: 600W, incandescent, ½ HP Motor or 1800W (15A) Resistive Range: Up to 100 feet line of sight between the Wireless Controller and the closest Z-Wave receiver module. Operating Temperature Range: 32-104° F (0-40° C) For indoor use only.
Specifications subject to change without notice due to continuing product improvement
Z-Wave is a registered US trademark of Zensys A/S
is a trademark of General Electric Company and is used under license to Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114 www.jascoproducts.com
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.