EN
GE logo
Official user manual

GE 3

12 pages·382 KB·Freezer·PDF·ENDEFRITNLJA
GE 3
Table of Contents 19 sections TABLE OF CONTENTS · Safety Information · Safety Precautions · Proper Disposal of Refrigerator · … ShowHide
Page 3 of the GE 3 user manual — USE OF EXTENSION CORDS
Page 3 · click to enlarge
Page 3

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

IThis refrigerator must be properly installed

IKeep fingers out of the “pinch point” areas;

and located in accordance with the Installation Instructions before it is used.

clearances between the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

IDo not allow children to climb, stand or hang

on the shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves.

IUnplug the refrigerator before cleaning and

making repairs.

IDo not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other appliance.

ITurning the temperature control dial to the

OFF position stops cooling but does not shut off power to the refrigerator.

DANGER! RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous…even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents.

CFC Disposal

Your old refrigerator has a cooling system that used CFCs (chlorofluorocarbons). CFCs are believed to harm stratospheric ozone.

If you are throwing away your old refrigerator, make sure the CFC refrigerant is removed for proper disposal by a qualified servicer. If you intentionally release this CFC refrigerant you can be subject to fines and imprisonment under provisions of environmental legislation.

Before You Throw Away Your Old Refrigerator or Freezer:

ITake off the doors.

ILeave the shelves in place so that children may

not easily climb inside.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

Page 4 of the GE 3 user manual — Read and follow this Safety Information carefully. SAVE THESE INSTRUCTIONS
Page 4 · click to enlarge
Page 4

Customer Service Troubleshooting Tips Operating Instructions Safety Instructions Installation Instructions Customer Service Troubleshooting Tips Installation Instructions Safety Instructions Operating Instructions Customer Service Troubleshooting Tips Installation Instructions Safety Instructions Operating Instructions

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

If you have only a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

USE OF ADAPTER PLUGS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.

However, if you must use an adapter, where local codes permit, a temporary connection may be made to a properly grounded 2-prong wall outlet by use of a UL-listed adapter available at most local hardware stores.

If the adapter ground terminal breaks, DO NOT USE the refrigerator until a proper ground has been established.

Attaching the adapter ground terminal to a wall outlet cover screw does not ground the appliance unless the cover screw is metal, and not insulated, and the wall outlet is grounded through the house wiring. You should have the circuit checked by a qualified electrician to make sure the outlet is properly grounded.

The larger slot in the adapter must be aligned with the larger slot in the wall outlet to provide proper polarity in the connection of the power cord.

When disconnecting the power cord from the adapter, always hold the adapter in place with one hand while pulling the power cord plug with the other hand. If this is not done, the adapter ground terminal is very likely to break with repeated use.

Read and follow this Safety Information carefully. SAVE THESE INSTRUCTIONS

Page 5 of the GE 3 user manual — Door Shelves
Page 5 · click to enlarge
Page 5

About the control on the refrigerator.

OFF

COLDEST

COLD

COLDEST OFF

COOL

COOL

COOL COLD

COLDEST

COLD

OFF

The control will look like one of the above.

Control Settings

The temperature control maintains the temperature in the refrigerator. Setting the control at COOL is the warmest setting. Setting the control at COLDEST is the coldest setting. Set the control at COLD.

Allow 24 hours for the refrigerator to reach the COLD temperature. If you want a colder or warmer temperature, move the dial one setting at a time. Moving the control to OFF stops cooling but does not turn off the power to the refrigerator. Setting the control to one of the snowflake positions may cause freezing in the refrigerator depending on the room temperature.

How To Test Temperatures

Use the milk test. Place a container of milk on a shelf and check it a day later. If the milk is too warm or too cold, adjust the temperature control.

After changing the control, allow 24 hours for the refrigerator to reach the temperature you have set.

About the inside of the refrigerator.

Shelves

To remove a shelf, lift up the back slightly and pull forward. Some models have multi- position shelves that can be moved to different levels.

Ice Tray Compartment

This compartment is designed for production of ice cubes and short-term storage (a few days at most) of some commercially-frozen foods when in contact with the evaporator (cold surface in compartment.)

Door Shelves

Shelves on the door provide convenient storage for frequently used items.

Some models have doors that are deep enough to store large bottles.

Page 6 of the GE 3 user manual — Preparing to Move
Page 6 · click to enlarge
Page 6

Customer Service Troubleshooting Tips Operating Instructions Safety Instructions Installation Instructions Customer Service Troubleshooting Tips Installation Instructions Safety Instructions Operating Instructions Customer Service Troubleshooting Tips Installation Instructions Safety Instructions Operating Instructions

Care and cleaning of the refrigerator.

Cleaning the Outside

Keep the outside clean. Wipe with a clean cloth lightly dampened with kitchen appliance wax or mild liquid dish detergent. Dry and polish with a clean, soft cloth.

Protect the paint finish. The finish on the outside of the refrigerator is a high quality, baked-on paint finish. With proper care, it will stay new-looking and rust-free for years. Apply a coat of kitchen/appliance wax when the refrigerator is new, and then at least twice a year.

Do not wipe the refrigerator with a soiled dish cloth or wet towel. These may leave a residue that can erode the paint. Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box of baking soda in the refrigerator.

Other parts of the refrigerator—including door gaskets, fruit and vegetable drawers, and all plastic parts—can be cleaned the same way.

Unplug the refrigerator before cleaning. If this is not practical, wring excess moisture out of sponge or cloth when cleaning around the control.

Do not wash any plastic refrigerator parts in the dishwasher.

Use warm water and baking soda solution— about a tablespoon (15 ml) of baking soda to a quart (1 L) of water. This both cleans and neutralizes odors. Rinse and wipe dry.

Defrosting

Defrost whenever frost on the wall of the ice tray compartment becomes 1/4″ thick. Never use a sharp or metallic instrument to remove frost as it may damage the cooling coils. (A punctured cooling coil will cause serious problems and void the warranty.) We recommend using a plastic scraper. Do not use any electrical device in defrosting your refrigerator.

After defrosting, empty water from the drip tray. Wash the drip tray in warm water. Wipe the ice tray compartment with a damp cloth. Then turn the temperature control to the desired setting and return food and ice trays to the refrigerator.

To defrost, remove foods and ice trays from the ice tray compartment. Set the temperature control dial at OFF position. Defrosting usually takes a few hours. To defrost faster, keep the door open. Also, pouring warm (not hot) water on the frosted part may speed defrosting. Do not use boiling water—it may damage plastic parts.

Preparing for Vacation

For long vacations or absences, remove food and unplug the refrigerator. Move the control to the OFF position, and clean the interior with a baking soda solution of one tablespoon (15 ml) of baking soda to one quart (1 liter) of water. Leave the door open.

Preparing to Move

Secure all loose items such as shelves and ice trays by taping them securely in place to prevent damage.

Be sure the refrigerator stays in an upright position during moving.

Page 7 of the GE 3 user manual — Clearances
Page 7 · click to enlarge
Page 7

Preparing to install the refrigerator.

Read these instructions completely and carefully.

Refrigerator Location

I Do not install the refrigerator where the

I Do not install it closer than 5″ (13 cm) next

temperature will go below 50°F (10°C) because it will not run often enough to maintain proper temperatures.

to a range.

I Do not install it in a recessed area.

I Do not build in the refrigerator.

I Install it on a floor strong enough to support it

fully loaded.

I If the Model 2 is placed on a countertop or stand,

the front surface of the door should be 3″ or more back from the edge of the countertop or stand to avoid accidental tipping of the appliance during normal use.

Clearances

Allow the following clearances for ease of installation and proper air circulation.

Sides 1/2″ (13 mm)

Top 2″ (51 mm)

Back 2″ (51 mm) from the rear cabinet surface to the wall

Leveling Legs (on some models)

Adjustable legs at the front corners of the refrigerator should be set so the refrigerator is firmly positioned on the floor and the front is raised just enough that the door closes easily when opened about halfway.

To adjust the leveling legs, turn the legs counterclockwise to raise the refrigerator, clockwise to lower it.

Turn counterclockwise to raise, clockwise to lower.

Page 8 of the GE 3 user manual — Model 3
Page 8 · click to enlarge
Page 8

Customer Service Troubleshooting Tips Operating Instructions Safety Instructions Installation Instructions Customer Service Troubleshooting Tips Installation Instructions Safety Instructions Operating Instructions Customer Service Troubleshooting Tips Installation Instructions Safety Instructions Operating Instructions

Preparing to install the refrigerator.

Read these instructions completely and carefully.

Door reversal

Model 3

1. Remove the small plug button on the left side of the door top cap.

Hinge cover Plug buttons or screws

2. Remove the three plug buttons or screws on the left side on top of the cabinet.
3. Remove the plastic hinge cover by lifting it up by the front edge.
4. Remove the three screws from the top hinge.
5. Lift the door up and off the bottom hinge (right side).
6. Tilt the refrigerator cabinet back to remove the right leveling leg.
7. Remove the screws on the bottom hinge (right side) and the left leveling leg. Move the bottom hinge to the left side and secure it with the screws and leveling leg.
8. Screw the right leveling leg, with the spacer in place, back in place on the right side.
9. Position the door on the left bottom hinge. With the magnetic gasket holding the door in place, secure the top hinge with screws.
10. Make sure the door is aligned with the refrigerator cabinet before continuing.
11. Replace the hinge cover on top of the hinge.
12. Put the plug button in the hole on the right side of the door cap.
13. Put the three plug buttons or screws on the right side on top of the cabinet.
Show 5 more labels / short text on this page
Hinge · Plug button · Bottom hinge · Spacer · Leveling legs
Page 9 of the GE 3 user manual — Model 4
Page 9 · click to enlarge
Page 9

Model 4

1. Remove the two screws at the back of the top cover.
2. Remove the top cover by lifting the back up about 2 inches and then sliding it forward.

Upper hinge Top cover

3. Remove the small plug button on the left side of the door top cap.
4. Remove the three screws on the upper hinge (right side). Remove the hinge.
5. Remove the three screws at the left hinge location on the top plate.
6. Remove the screw in the middle of the top plate and remove the top plate.
7. Lift the door up and off the bottom hinge (right side).
8. Tilt the refrigerator cabinet back to remove the right leveling leg.
9. Remove the screws on the bottom hinge (right side) and the left leveling leg. Move the bottom hinge to the left side and secure it with the screws and leveling leg.
10. Screw the right leveling leg, with the spacer in place, back in place on the right side.
11. Position the door on the left bottom hinge. With the magnetic gasket holding the door in place, secure the top hinge with screws.
12. Make sure the door is aligned with the refrigerator cabinet before continuing.
13. Replace the top plate and screws.
14. Slide the top cover back in place and replace the two screws.
15. Put the plug button in the hole on the right side of the door top cap.
Show 7 more labels / short text on this page
Left hinge location · Top plate · Plug button · Door top cap · Bottom hinge · Spacer · Leveling legs
Page 10 of the GE 3 user manual — Before you call for service…
Page 10 · click to enlarge
Page 10

Customer Service Troubleshooting Tips Operating Instructions Safety Instructions Installation Instructions Customer Service Troubleshooting Tips Installation Instructions Safety Instructions Operating Instructions Customer Service Troubleshooting Tips Installation Instructions Safety Instructions Operating Instructions

Before you call for service…

Troubleshooting Tips Save time and money! Review the charts below first and you may not need to call for service.

ProblemPossible Causes What To Do Refrigerator does not operateControl in OFF position. •Move the control to a temperature setting. Refrigerator is unplugged. •Push the plug completely into the outlet. The fuse is blown/circuit •Replace fuse or reset the breaker. breaker is tripped. Vibration or rattling (slight vibration is normal)Front leveling legs (on some •See Leveling Legs. models) need adjusting. Refrigerator is on an •Use shims to level the refrigerator. uneven surface. Motor operates for long periods or cyclesNormal when refrigerator •Wait 24 hours for the refrigerator to completely is first plugged in. cool down. Often occurs when large •This is normal. amounts of food are placed in refrigerator. Door left open. •Check to see if package is holding door open. Hot weather or frequent •This is normal. door openings. Temperature control •See About the control. set at the coldest setting. Not enough clearance •Make sure there is enough air circulation around the from the wall. refrigerator. Refrigerator too warmTemperature control not set •See About the control. cold enough. Warm weather or frequent •Set the temperature control one step colder. door openings. See About the control. Door left open. •Check to see if package is holding door open. Cabinet sides are warm. •This is normal for a hot wall type condenser. Refrigerator has odorFoods transmitting •Foods with strong odors should be tightly wrapped. odor to refrigerator. •Keep an open box of baking soda in the refrigerator; replace every three months. Interior needs cleaning. •See Care and cleaning. Defrost water pan needs cleaning. •See Care and cleaning. Moisture forms on outside of refrigeratorNot unusual during •Wipe surface dry. periods of high humidity. Moisture collects inside (in humid weather, air carries moisture into refrigerator when door is opened)Too frequent or too long door openings. Refrigerator too coldTemperature control •See About the control. set too cold.
Page 11 of the GE 3 user manual — Warrantor: General Electric Company. Louisville, KY 40225
Page 11 · click to enlarge
Page 11

Refrigerator Warranty. (For customers in the United States)

All warranty service provided by our Factory Service Centers, or an authorized Customer Care® technician. For service, call 800-GE-CARES.

For The Period Of: GE Will Replace:

One Year Any part of the refrigerator which fails due to a defect in materials or workmanship. From the date of the During this limited one-year warranty, GE will also provide, free of charge, all labor original purchase (does not include service trip to home) to replace the defective part.

Five Years The compressor if it fails due to a defect in materials or workmanship. (Does not From the date of the include service labor charges or service trips to home.) original purchase

What GE Will Not Cover:

IService trips to your home to teach you how to use the

IReplacement of house fuses or resetting of circuit

product.

breakers.

IImproper installation.

IDamage to the product caused by accident, fire, floods or

IFailure of the product if it is abused, misused, or used for

acts of God.

other than the intended purpose or used commercially.

IIncidental or consequential damage to personal property

caused by possible defects with this appliance.

ILoss of food due to spoilage.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

Page 12 of the GE 3 user manual — Service Satisfaction
Page 12 · click to enlarge
Page 12

Customer Service Troubleshooting Tips Operating Instructions Safety Instructions Installation Instructions Customer Service Troubleshooting Tips Installation Instructions Safety Instructions Operating Instructions Customer Service Troubleshooting Tips Installation Instructions Safety Instructions Operating Instructions

Service Telephone Numbers.

GE Answer Center ® 800.626.2000

The GE Answer Center® is open 24 hours a day, 7 days a week.

In-Home Repair Service 800-GE-CARES (800-432-2737)

Expert GE repair service is only a phone call away.

Special Needs Service 800.626.2000

800-TDD-GEAC (800-833-4322)

GE offers, free of charge, a brochure to assist in planning a barrier-free kitchen for persons with limited mobility.

Service Contracts 800-626-2224

Purchase a GE service contract while your warranty is still in effect and you’ll receive a substantial discount. GE Consumer Service will still be there after your warranty expires.

Parts and Accessories 800-626-2002

Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes (VISA, MasterCard and Discover cards are accepted).

Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause unsafe operation.

Service Satisfaction

If you are not satisfied with the service you receive from GE:

First, contact the people who serviced your appliance.

Next, if you are still not pleased, write all the details—including your phone number—to:

Manager, Customer Relations GE Appliances Appliance Park Louisville, KY 40225

Printed in China 12

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Refrigerator does not operateControl in OFF position. •Move the control to a temperature setting. Refrigerator is unplugged. •Push the plug completely into the outlet. The fuse is blown/circuit •Replace fuse or reset the breaker. breaker is tripped. p.10
Vibration or rattling (slight vibration is normal)Front leveling legs (on some •See Leveling Legs. models) need adjusting. Refrigerator is on an •Use shims to level the refrigerator. uneven surface. p.10
Motor operates for long periods or cyclesNormal when refrigerator •Wait 24 hours for the refrigerator to completely is first plugged in. cool down. Often occurs when large •This is normal. amounts of food are placed in refrigerator. Door left open. •Check to see if package is holding door open. Hot weather or frequent •This is normal. door openings. Temperature control •See About the control. set at the coldest setting. Not enough clearance •Make sure there is enough air circulation around the from the wall. refrigerator. p.10
Refrigerator too warmTemperature control not set •See About the control. cold enough. Warm weather or frequent •Set the temperature control one step colder. door openings. See About the control. Door left open. •Check to see if package is holding door open. Cabinet sides are warm. •This is normal for a hot wall type condenser. p.10
Refrigerator has odorFoods transmitting •Foods with strong odors should be tightly wrapped. odor to refrigerator. •Keep an open box of baking soda in the refrigerator; replace every three months. Interior needs cleaning. •See Care and cleaning. Defrost water pan needs cleaning. •See Care and cleaning. p.10
Moisture forms on outside of refrigeratorNot unusual during •Wipe surface dry. periods of high humidity. p.10
Moisture collects inside (in humid weather, air carries moisture into refrigerator when door is opened)Too frequent or too long door openings. p.10
Refrigerator too coldTemperature control •See About the control. set too cold. p.10

Ask about the GE 3

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the GE 3

Be the first to ask — other owners or our team will answer.

Original document

GE 3 manual PDF

12 pages·382 KB·Freezer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…