Instruction/ maintenance manual of the product 229C4053P447-3 1 GE
Go to page of 12
Skill Level: High A verage Low Completion Time: 1 to 3 Hours Proper installation is the responsibility of the installer . Product failure due to improper installation is not covered under the GE Appliance W arranty . See the Owners Manual for warranty information.
All rough-in and spacing dimensions must be met for safe use of your range. Electricity to the range can be disconnected at the outlet without moving the range if the outlet is in the preferred location (remove lower drawer).
3 Installation Instructions Pre- Installation Checklist Preparing the Range Open oven door and remove literature pack, broiler pan and grid, and oven racks. Remove packaging materials. Any packaging materials must be removed during installation. This will include adhesive tape, wire ties, cardboard and protective plastic.
4 Installation Instructions Installation Required Clearances A ***6" MIN **30" MIN **15" MIN *0" *0" See Ilustrations below for all rough-in and spacing dimensions. The range may be placed with 0 ” clearance (flush) at the back wall and side walls of the cabinet.
5 Installation Instructions Electrical Connections B B1 Making the Electrical Connection Remove the wire cover (on the back of the range) by removing 5 screws using a 1/4 ” nut driver . Do not discard these screws. B2 All new constructions, mobile homes and installations where local codes do not allow grounding through neutral.
Installation Instructions Electrical Connections cont. B B3 Complete 4 wire cord kit. Below are step by step instructions on how to install the kit. B4 Remove the screws on the terminal block with a 1/4 ” nut driver or phillips screwdriver .
Installation Instructions Electrical Connections cont. B B3a Complete 3 wire cord kit. Below are step by step instructions on how to install the kit. B4a Remove the screws on the terminal block with a 1/4 ” nut driver or phillips screwdriver .
8 Installation Instructions Installing the Anti-Tip Bracket C a. For concrete installation you will need two 1/4"x 1-1/2" lag screws, and two sleeve anchors. b. Locate the center of the four holes identified in Fig. 1 as Floor-Concrete and Wall.
9 Installation Instructions Installing the Range D D4 When installation is complete and the range is in place, inspect to be sure the rear leveling leg is fully inserted into the slot of the Anti-Tip Bracket.
10 Installation Instructions Installing the Range cont. D Place the drawer rail on the guides. Replacing the Storage Drawer D13 Push the drawer in until it stops.
11 Final Check List Operation Check List Check to make sure the circuit breaker is closed (Reset) or the circuit fuses are replaced. Be sure power is in service to the building. Check to be sure that all packing materials and tape on metal panel (if applicable) under control knobs have been removed.
12 NOTES Pub. No. 31-10463 229C 4053P447-3.
An important point after buying a device GE 229C4053P447-3 1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE 229C4053P447-3 1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE 229C4053P447-3 1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE 229C4053P447-3 1 you will learn all the available features of the product, as well as information on its operation. The information that you get GE 229C4053P447-3 1 will certainly help you make a decision on the purchase.
If you already are a holder of GE 229C4053P447-3 1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE 229C4053P447-3 1.
However, one of the most important roles played by the user manual is to help in solving problems with GE 229C4053P447-3 1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE 229C4053P447-3 1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
