Instruction/ maintenance manual of the product 500-2D Alto-Shaam
Go to page of 27
MN-29742 (R e v . 1) • 04/13 p r i n t e d i n u . s . a . Drawer Warmers Electric Models : 500-1D, 1DN 500-2D, 2DN 500-3D, 3DN • InstallatIon • operatIon • MaIntenance W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA PHONE: 262.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • b Delivery ............................................................................. 1 Unpacking ..............................................................
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 1 DELIVERY This Alto-Shaam appliance has been thoroughly tested and inspected to ensure only the highest quality unit is provided. Upon receipt, check for any possible shipping damage and report it at once to the delivering carrier.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 2 CAUTION Used to indicate the presence of a hazard that can or will cause minor personal injury, property damage, or a potential unsafe practice if the warning included with this symbol is ignored.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 3 SITE INSTALLATION This Alto-Shaam appliance must be installed in a location that will permit it to function for its intended purpose and to allow adequate clearance for ventilation, proper cleaning, and maintenance access.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 4 12-5/16" (312mm) 24-5/8" (624mm) 43-3/8" (1101mm) 24-7/8" (631mm) 26-1/8" (664mm) 25-.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 5 26-1/8" (664mm) 31-3/16" (792mm) 11-5/8" (296mm) 18-15/16" (481mm) 500-1D 500-2D 500-3D El.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 6 1. An identification tag is permanently mounted on the cabinet. 2. Plug cabinet into a properly grounded receptacle ONLY, positioning the unit so the power supply cord is easily accessible in case of an emergency.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 7 This appliance is intended for use in commercial establishments where all operators are familiar with the purpose, limitations, and associated hazards of this appliance.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 8 1 . PREHEAT AT 200°F (93°C) FOR 30 MINUTES BEFORE LOADING FOOD. Push power switch to “ON” position. The unit will begin operating at the previous set temperature.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 9 GENERAL HOLDING GUIDELINES Chefs, cooks and other specialized food service personnel employ varied methods of cooking.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 10 CAUTION TO PROTECT STAINLESS STEEL SURFACES, COMPLETELY AVOID THE USE OF ABRASIVE CLEANING COMPOUNDS, CHLORIDE BASED CLEANERS, OR CLEANERS CONTAINING QUATERNARY SALTS.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 11 THOROUGHLY CLEAN DAILY : 1. Disconnect unit from power source, and let cool. 2. Remove, cover or wrap, and refrigerate food. 3. Remove drawer pans and clean separately.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 12 Food fl avor and aroma are usually so closely related that it is diffi cult, if not impossible, to separate them. There is also an important, inseparable relationship between cleanliness and food fl avor.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 13 THERMOSTAT ACCURACY The electronic thermostat is a precise instrument and is designed to offer trouble free service.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 14 TROUBLE SHOOTING - ELECTRONIC CONTROL INSTALLATION Code Description Possible Cause E-10 Cavity air sensor shorted Cavity air sensor reading < 5°F. Verify sensor integrity.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 15 SERVICE 1 23 4 5 6 27 26 25 22 21 24 10 19 20 16 15 18 17 11 12 13 14 9 7 8 23 SERVICE VIEW - EXTERIOR 500-2D Shown Part numbers and drawings are subject to change without notice.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 16 MODEL > 500-1D 500-2D 500-3D ITEM DESCRIPTION PART NO. QTY PART NO. QTY PART NO. QTY 1 TOP COVER 1012473 1 1012473 1 1012473 1 2 REAR TRIM 1012665 1 1012674 1 1012446 1 3 RIVET , BLIND, #44, S/S 28 RI-2100 24 RI-2100 28 RI-2100 30 4 GASKET ADHESIVE 0.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 17 SERVICE 3 4 5 1 2 12 11 10 6 13 8 7 9 SERVICE VIEW - DRAWER ASSEMBLY (5013915) 500-D Part numbers and drawings are subject to change without notice. ITEM DESCRIPTION PART NO.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 18 SERVICE 4 6 5 1 2 11 12 10 17 18 19 20 23 24 25 26 27 28 29 21 22 13 14 15 16 3 9 7 8 SERVICE VIEW - EXTERIOR 500-1DN Shown Part numbers and drawings are subject to change without notice.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 19 SERVICE MODEL > 500-1DN 500-2DN 500-3DN ITEM DESCRIPTION PART NO. QTY PART NO. QTY PART NO. QTY 1 TOP COVER 1012779 1 1012779 1 1012779 1 2 GASKET ADHESIVE 0.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 20 SERVICE 7 6 5 9 10 12 14 13 4 1 8 3 2 11 SERVICE VIEW - DRAWER ASSEMBLY (5014435) 500-DN Part numbers and drawings are subject to change without notice. Item #10 must be order ed when installing item #11 ITEM DESCRIPTION PART NO.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 21 SERVICE 6 5 8 7 4 3 1 2 10 9 SERVICE VIEW - ELECTRICAL Part numbers and drawings are subject to change without notice. ITEM DESCRIPTION PART NO. QTY 1 BUSHING, 3/8" HOLE BU-3419 1 2 ELECTRIC CHASSIS 5014441 1 3 WASHER, INT .
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 22.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 23.
MN-29742 • Rev. 1 (04/13) • Drawer Warmer Installation/Operation/Service Manual • 24.
TRANSPORTATION DAMAGE and CLAIMS All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the carrier, such shipments become the property of the consignee. Should damage occur in shipment, it is a matter between the carrier and the consignee.
An important point after buying a device Alto-Shaam 500-2D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Alto-Shaam 500-2D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Alto-Shaam 500-2D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Alto-Shaam 500-2D you will learn all the available features of the product, as well as information on its operation. The information that you get Alto-Shaam 500-2D will certainly help you make a decision on the purchase.
If you already are a holder of Alto-Shaam 500-2D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Alto-Shaam 500-2D.
However, one of the most important roles played by the user manual is to help in solving problems with Alto-Shaam 500-2D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Alto-Shaam 500-2D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
