Instruction/ maintenance manual of the product GP-150 Furuno
Go to page of 97
GPS NA VIGA T OR GP-150.
The paper used in this manual is elemental chlorine free. FURUNO Aut hor i ze d Di s t ri but o r / Dealer FURUNO Aut hor i ze d Di s t ri but o r / Dealer 9-52 A shihar a-cho, 9-52 A shihar a-cho, Ni.
i IMPORT ANT NOTICE • This manual is intend ed for use by native speakers of En glish. • No part of this manual may be cop ied or reproduced without written permission. • If this manual is lost or worn, contact your dealer ab out replacement. • The content s of this manual and equip ment specifications are su bject to change without notice.
ii SAFETY INSTRUCTIONS CAUTION Use the correct fuse. Use of the wrong fuse can cause fire or equipment damage. No single navigation aid (including this unit) should ever be relied upon as the exclusive means for navigating your vessel. The navigator is responsible for checking all aids available to confirm his position.
iii T ABLE OF CONTENTS FOREWORD ............................................. iv SYSTEM CONFIGRA TI ON ........................ v 1. OPERA TI ONAL OVERVIEW 1.1 Control De scription ......................... 1-1 1.2 T urning On and Off the Power ......
iv FOREWORD A Word to GP-150 Owners Congratulations on your choice of the FURUNO GP-150 GPS Navigator . We are confident you will see why the FURUNO name has become synonymous with quality and reliability . For over 50 years FURUNO Electric Company has enjoyed an enviable reput ation for innovative and dependable marine electronics equipment.
v SYSTEM CONFIGURA TION Antenna Unit GPA-018S* Display Unit Radar, Echosounder, Autopilot etc. DGPS Beacon Receiver GR-80** 12-24VDC Antenna Unit GPA-017S** Antenna Unit GPA-019S* *: w/internal beacon.
vi This page in tentionally left blank..
1-1 1. OPERA TIONAL OVER VIEW 1.1 Control Description Cursor pads Shift display and cursor . Adjusts display contrast and brilliance; changes latitude/longitude coordinate. T urns power on/of f. Sets destination. Deletes waypoints and marks; clears wrong data; silences audible alarm.
1. OPERA TION 1-2 1.2 T urning On and Off the Power The GP-150 takes about 90 seconds to find position when turned on for the very first time. Thereafter it t akes about 12 seconds to find position each time the power is turned on. T urning on the power Press the POWER key .
1. OPERA TION 1-3 1.3 Adjusting Display Contrast and Brilliance 1) Press the TON E ke y . The display shown in Figure 1-3 appears. T one: Brilliance: [-] [+] MENU : Escape 17 (0~31) 7 (0~7) Figure 1-3 Screen for adjustment of display contrast and brilliance 2) T o adjust contrast, press or .
1. OPERA TION 1-4 Plotter 1 display 44 ° D3D 100m SAFE 34 ° 23.456´ N 135 ° 45.678´ E BRG 32 ° BRG TO + 11.5 RNG TO + nm 123 ° COG [01] 30 40 20 50 H 2.
1. OPERA TION 1-5 Navigation display 1) No autopilot connection E 3D N S 12.3 SOG 10.3 123 RNG 789 TRIP nm kt VTD kt nm BRG 23:45' 17H 45M TO; 012 0.
1. OPERA TION 1-6 Dat a display Refer to Chapter 6 for user-defined window setting. The ZOOM icon can be disp layed by pressing the CURSOR ON/OFF key . SEP 12, 2005 23:59'59" U 12 ° 23.456' N 123 ° 23.456' E POSITION RNG 31.23 nm SOG 12.
2-1 2. TRACK 2.1 Enlarging/Shrinking the Display Y ou may enlarge and shrink the display on the Plotter 1, Plotter 2 and Highway displays, with the ZOOM IN and ZOOM OUT keys. The horizontal range is availa ble among 0.25, 0.5, 1, 2, 4, 8, 16, 32, 64, 128 and 192 nautical miles for Plotter 1 and Highway , and 0.
2. TRACK 2-2 Cursor turned off Ship's position (in latitude and longitude or LOPs), speed and course appear on the display . 234 ° 34 ° 23.456´ N 135 ° 45.
2. TRACK 2-3 234 ° 34 ° 23.456· N 135 ° 45.678· E BRG 345 ° RNG 123 12.3 SOG nm kt COG H Hold icon (appears while recording of track is stopped) D3D 100m SAFE Recording is stopped.
2. TRACK 2-4 Are you sure to erase ? ENT : Y es MENU: No Figure 2-6 Prompt for erasure of track 5) Press the NU/CU ENT key . 2.9 Selecting T rack Plotting Interval The plotting interval determines both how the track will be reconstructed on the display and track storage time.
2. TRACK 2-5 2.10 Apportioning the Memory The memory holds 2,000 points of tr ack and marks and may be apportioned as you like. The default memory setting stores 1,000 points each of track and marks. CAUTION All data are erased whenever the memory apportion setting is changed, even when the previous value is re-entered.
2. TRACK 2-6 2.1 1 Selecting Bearing Reference Ship's course and bearing to waypoint may be displayed in true or magnetic bearing. Magnetic bearing is true bearing plus (or minus) earth's magnetic deviation. Displaying true or magnetic bearing The default setting displays true bearings.
3-1 3. MARKS 3.1 Entering/Erasing Marks Marks can be inscribed on the Plott er 1 and Plotter 2 displays. Y ou may inscribe a mark anywhere, in one of 13 shapes. Further , marks can be connected with lines. Note 1: When the mark memory becomes full no marks can be entered.
3-2 3.2 Selecting Mark Shape 13 mark shapes are available. Select mark shape as follows: 1) Press MENU ESC and 2 to display the TRACK/MARK SETUP menu. TRACK/MARK SETUP T rack Rec Mark Shape Mark Line Event Mark T ime (01’00) Dist (00.50nm) : Select ENT : Enter MENU: Escape Figure 3-4 TR ACK/MARK SETUP menu 2) Press or to select Mark Shape.
3. MARKS 3-3 3.4 Entering Event Marks Event marks can denote any important present position. Event marks can be saved as ordinary marks and the unit automatically numbers them from 01 to 99. Note 1: When the mark memory becomes full no event marks can be entered.
3-4 3.6 Entering the MOB Mark The MOB mark denotes man overboard position. T o mark man overboard position, press the EVENT MOB key more than three seconds. When the key is pressed, the position at the exact moment the key is pressed automatically becomes the destination.
4-1 4. NA VIGA TION PLANNING 4.1 Registering W aypoint s In navigation terminology a waypoint is a particular location on a voyage whether it be a starting, intermediate or destination waypoint. The GP-150 can store 999 waypoints, numbered from 001-999.
4. NA VIGA TION PLANNING 4-2 6) Press to select waypoint mark shape. The following display appears. : Cursor ENT : Enter MENU: Escape Figure 4-4 Screen for selecting waypoint mark shape 7) Press or to select mark shape. 8) Press the NU/CU ENT key . The display shown in Figure 4-5 appears.
4. NA VIGA TION PLANNING 4-3 Registering waypoint s by MOB position/event position The MOB position or an event position can be registered as a waypoint. Event marks are numbered from 01 to 99; 01 is the latest event mark. Note: Y ou cannot register a MOB position or event position when there are no MOB positions or event positions saved.
4. NA VIGA TION PLANNING 4-4 Note: Alternatively , you may enter position, leaving the waypoint number blank. 4) Enter range and bearing you wish to use to calculate position of new waypoint. 5) Press the NU/CU ENT key . The display now looks something like the one below .
4. NA VIGA TION PLANNING 4-5 4.2 Editing W aypoint s 1) Press WPT RTE and 5 . 2) Press or to select waypoint to edit. 3) Press . 4) Edit the content s of the waypoint.
4. NA VIGA TION PLANNING 4-6 4.4 Registering Routes Often a trip from one place to another involves several course changes, requiring a series of route points which you navigate to, one after another . The sequence of waypoints leading to the ultimate destination is called a route.
4. NA VIGA TION PLANNING 4-7 2 Using previousl y registered waypoints Enter waypoints in the or der they will be traversed; not by waypoint number order . 7) Press . The reverse video on the waypoint on route planning screen disappears. 8) Press or to select waypoint number .
4. NA VIGA TION PLANNING 4-8 4.7 Deleting Routes 1) Press WPT RTE and 6 to display the route list. 2) Press or to select route to delete. 3) Press the CLEAR key . The display shown in Figure 4-17 appears if the route is in use. 1st line Are you sure to erase ? ENT : Y es MENU: No This route is in use Figure 4-17 4) Press the NU/CU ENT key .
5-1 5. ST ARTING FOR DESTINA TION 5.1 Setting Destination There are four ways by which you can set destination: • By cursor • By MOB position or event position • By waypoint, and • By route. Note: Previous destination is cancelled whenever a destination is set.
5. ST AR TING FOR DESTINA TION 5-2 Flag mark Figure 5-4 Single destination set by cursor Setting multiple destinations 1) Press GOTO and 1 . 2) Place the cursor on the location desired for waypoint. 3) Press the NU/CU ENT key . 4) Repeat steps 2 and 3 to enter other points.
5. ST AR TING FOR DESTINA TION 5-3 Setting destination by MOB position or event position Note: This operation cannot be performed when there is no MOB position or event position. The buzzer sounds and the message shown in Figure 5-8 appears to alert you when there is no MOB position or event position.
5. ST AR TING FOR DESTINA TION 5-4 1 Setting destination by waypoint no. 3) Enter waypoint number , in three digits. Y ou can clear entry by pressing the CLEAR key . 4) Press the NU/CU ENT key . Own ship position becomes st arting point and a dashed line runs between it and the waypoint selected.
5. ST AR TING FOR DESTINA TION 5-5 Skipping route waypoint s Y ou may skip route waypoints by displaying "DI" (DIsable) next to the route waypoint in the route list. Using Figure 5-14 as an example, your ship is currently heading toward waypoint 04 but is to switch course and head to waypoint 03.
5. ST AR TING FOR DESTINA TION 5-6 5.3 Erasing Route W aypoint s (flags) 1) Place the cursor on the flag to erase. 2) Press the CLEAR key . The message shown in Figure 5-17 appears if the waypoint is currently selected as destination, is p art of a registered route, or is part of the route cur rently being navigated.
5. ST AR TING FOR DESTINA TION 5-7 5.4 Finding Range and Bearing Between T wo Point s Selecting Course Sailing Method The range and bearing to a destination are calculated by two ways: Great Circle or Rhumb Line. However , cross track error is calculated by rhumb line only .
5. ST AR TING FOR DESTINA TION 5-8 4) Press to shift the cursor to the T rial S peed line. 5) Press or to select Auto or Man. Auto uses ship's average speed to calculate time-to-go. 6) If you selected Man, enter speed. 7) Press the NU/CU ENT key .
6-1 6. SETTING UP V ARIOUS DISPLA YS 6.1 Selecting Dat a to Display on the Dat a Display The user may select what data to display in four locations on the dat a display . JAN 12, 2006 23:59’59" U 12 23.456’ N 123 23.456’ E POSITION RNG 31.23 nm SOG 12.
6. SETTING UP V ARIOUS DISPLA YS 6-2 6.2 Selecting Position Format Position can be displayed in latitude and longitude, Loran C LOPs, or Decca LOPs, and the default format is latitude and longitude. Selecting position format (L/L or LOPs) 1) Press MENU ESC , 9 and 8 to display the LOP SETUP menu.
6. SETTING UP V ARIOUS DISPLA YS 6-3 Registering waypoint s using LOPs 1) Press WPT RTE and 5 . 2) Press to display LOPs. W A YPOINT LIST (LOP , LC) 001 36365.
6. SETTING UP V ARIOUS DISPLA YS 6-4 6.3 Demo Display The demo display provides simulated operation of this unit. Own ship tracks, at the speed selected, a figure eight course, st arting from position entered. All controls are operative; you may change course, enter marks, etc.
7-1 7. ALARMS There are seven alarm conditions which generate both audible and visual alarms. When an alarm setting is violated, the buzzer sounds and the name of the of fending alarm appears on the display . The alarm icon also appears on the Plotter 1, Plotter 2 and Highway displays.
7. ALARMS 7-2 Anchor watch alarm The anchor watch alarm sounds to warn you that own ship is moving when it should be at rest. Alarm setting Own ship’s position Destination waypoint : Alarm range Figure 7-4 How the anchor watch alarm works Before setting the anchor watch alarm, set present position as destination waypoint, referring to chapter 5.
7. ALARMS 7-3 7.3 Ship’ s Speed Alarm The ship’s speed alarm sounds whe n ship's speed is lower or higher (or within) the alarm range set. 1) Press MENU ESC and 4 . 2) Press or to select Ship S peed. 3) Press or to select In (or Over). In: Alarm sounds when speed is within range set.
7. ALARMS 7-4 7.5 W ater T emperature Alarm The water temperature alarm sounds when the water temperature is higher or lower (or within) the preset temperature. This alarm requires temperature signal from external equipment. 1) Press MENU ESC and 4 . 2) Press or to select W ater T emp.
8-1 8. MENU SETTINGS 8.1 GPS Menu Menu description Fix mode T wo position fixing modes are available: 2D and 2/3D. The 2D mode provides two dimensional position fixes (latitude and longitude only) and is used when three satellites are in line of si ght of the GPS receiver .
8. MENU SETTINGS 8-2 Geodetic datum Select the geodetic chart system you are using. WGS-84 (standard GPS chart system) and NAD 27 can be directly selected. For other charts, select "OT HER" and enter chart number referring to the geodetic chart list in the Appendix.
8. MENU SETTINGS 8-3 Entering GPS speed smoothing 1) Press MENU ESC , 9 and 6 . 2) Press or to select S pd. 3) Enter smoothing factor in three digits (0000-9999). 4) Press the NU/CU ENT key . 5) Press the MENU ESC key . Entering speed averaging 1) Press MENU ESC , 9 and 6 .
8. MENU SETTINGS 8-4 Entering position After the unit is inst alled you may enter position to shorten the time it t akes to find position. (It takes about t wo minutes when there is no position data entered.) 1) Press MENU ESC , 9 and 6 . 2) Press or to select Posn on page 2/2.
8. MENU SETTINGS 8-5 8.3 Mark, Character Size and Brilliance The DISPLA Y SETUP menu lets you select the size and brilliance of various markers. Grid tone The grid can be displayed in light or dark tone, or turned off. 1) Press MENU ESC and 1 . The DISPLA Y SETUP menu appears.
8. MENU SETTINGS 8-6 Enlarging characters The size of the indications of posit ion or user defined display areas can be enlarged on the Data display . 1) On the Data display , with no enlarged characters, press the CURSOR ON /OFF key to turn on the zoom icon.
8. MENU SETTINGS 8-7 3) Press or to select NMEA 0183 (V1.5 or V2.0) or IEC 61 162-1. 4) Press the NU/CU ENT key . T alker ID appears in reverse video. 5) Press or to select GP , LC or DE. 6) Press the NU/CU ENT key . 7) Enter Tx interval for each output dat a sentence in line 1.
8. MENU SETTINGS 8-8 Setting DA T A 4 to NMEA The DA T A 4 port connects to a personal computer , DGPS receiver or YEOMAN equipment. 1) Press MENU ESC , 9 and 5 .
8. MENU SETTINGS 8-9 13) Press the NU/CU ENT key . The message shown in Figure 8-14 appears while data is being loaded. Now loading W aypoint/Route data ! MENU:Stop Figure 8-14 14) Operate the computer to output data. When data is loaded, th e cursor shift s to S top.
8. MENU SETTINGS 8-10 Loading completed V alid waypoint : 0 Invalid waypoint : 0 Press any key Figure 8-21 8) Press the [ MENU ESC ] key twice. Saving dat a to personal computer W aypoint and route data can be saved to a personal computer . 1) Press MENU ESC , 9 and 5 .
8. MENU SETTINGS 8-1 1 DGPS 1) Press MENU ESC , 9 and 7 to display the W AAS/DGPS SETUP menu. W AAS SEARCH Auto Man (GEO=134) Freq. 323.0kHz Baud Rate 200 bps W AAS/DGPS SETUP MENU : Escape ENT : Enter : Select MODE Of GPS Of CORRECTIONS DA T A SET : 00 DGPS Station Auto Man (ID=0274) Frequency appears when "Man" is selected.
8. MENU SETTINGS 8-12 T o Previous Page MSB Parity EVEN ODD NONE Stop Bit 1 2 Baud Rate 4800 9600 DA T A 4 I/O SETUP "DGPS" 2/2 MENU : Escape ENT : Enter : Select First Bit LSB Figure 8-27 DA T A 4 I/O SETUP "DGPS" 2/2 menu 7) Press or to select First Bit.
9-1 9. MAINTE- NANCE & TROUBLE- SHOOTING 9.1 Clearing the Memory The GP-150 has two memories: GPS memory and plotter memory . Clearing the plotter memory The plotter memory holds plotted track and mark data. When you clear the plott er memory , all track and marks are cleared and all corresponding defaults settings a re restored.
9. MAINTENANCE & TROUBLESHOOTING 9-2 9.2 Preventive Maintenance Regular maintenance is necessary to maintain performance. Check the item s mentioned below monthly to keep the equipment in good working order . Antenna unit Check for fixing bolts for tightness.
9. MAINTENANCE & TROUBLESHOOTING 9-3 Press the CLEAR key to silence the buzzer . If the CLEAR key is not pressed, several beeps sound every three minutes. DGPS error When DGPS data cont ains errors or the DGPS beacon station is experiencing transmitting problems, the message shown in Figure 9-7 appears.
9. MAINTENANCE & TROUBLESHOOTING 9-4 9.4 T roubleshooting The table which follows provides troubleshooting procedures which you can follow to restore normal operation.
9. MAINTENANCE & TROUBLESHOOTING 9-5 9.5 Diagnostic T est s Memory and I/O circuit s test 1) Press MENU ESC and 8 to display the SELF TESTS menu. 1. Memory , I/O Port T est 2. Keyboard T est 3. T est Pattern 4. Automatic T esting SELF TESTS 2. Keyboard T est MENU:Escape :Cursor GPS PROGRAM No.
9. MAINTENANCE & TROUBLESHOOTING 9-6 Display test 1) Press MENU ESC , 8 and 3 to display the test pattern screens. 2) T o change the test pattern, press the NU/CU ENT key . Each time the key is pressed one of the patterns shown in Figure 9-12 appears.
A P-1 MENU TREE Main menu c ESC MENU 1. DISPLA Y SETUP 2. TRACK/MARK SETUP 3. ERASE TRACK/MARK 4. ALARM SETTINGS 5. MANUAL CALCULA TION 6. 7. GPS MONITOR SA TELLITES MONITOR BEACON RCVR MONITOR ST A TION MESSAGE From To T rial Speed ( A uto , Man) (010.
APPENDIX AP-2 1. PLOTTER SETUP 2. UNIT SETUP 4. DA T A2 OUTPUT SETUP 5. DA T A4 I/O SETUP 9. SYSTEM SETTINGS Unit of Depth (m, ft , F A) Unit of T emp. ( ° C , ° F) 3. DA T A1, 3 OUTPUT SETUP Unit of Altitude (m, ft ) Unit of Distance ( nm , km, sm) Data ( Out , Com.
APPENDIX A P-3 6. GPS SETUP 7. W AAS/DGPS SETUP 8. LOP SETUP 9. CLEAR MEMORY Spd ( 0005 , 0000 - 9999 sec) Posn ( 0000 , 0000 - 9999 sec) ANT Height (016 ft, 000 - 999 ft) Disable Satellite (1 - 32) G.
APPENDIX AP-4 DIGIT AL INTERF ACE (IEC 61 162-1 EDITION 2 (2000-07)) Output sentences of channel 1, 2, 3, 4 (DA T A 1, DA T A 2, DA T A 3, DA T A 4) AAM, APB, BOD, BWC, BWR, BWW , GBS, GGA, GLL, GNS, .
APPENDIX A P-5 1 2 6 4 3 2 DATA 1 J5 TD-A TD-B FL4 FL5 MJ-A6SRMD 20P8192 U25 SN75ALS172 DA T A 1 port (input) 1 J5 2 3 4 5 6 RD-H RD-C 1 3 4 5 FL7 DATA 1 20P8192 MJ-A6SRMD FL6 CR15 1SS272 PC-400 U26 +3.3V R130 2.2K R182 100 JP1 R123 390 • Load Requ irements Isolation: opto coupler Input Impedance: 470 Ω Max.
APPENDIX AP-6 DA T A 2 port (output) Output drive cap ability: Max. 15mA 1 J7 2 3 4 5 6 DATA2 TD-A TD-B FL9 20P8192 MJ-A6SRMD FL8 6 7 8 U25 SN75ALS172 DA T A 2 port (input) 1 3 4 5 1 J7 2 3 4 5 6 DATA2 FL11 20P8192 MJ-A6SRMD FL10 CR15 1SS272 PC-400 U27 +3.
APPENDIX A P-7 DA T A 3 port (output) Output drive cap ability: Max. 15mA 20P8192 MJ-A6SRMD 14 13 12 2 2 1 1 DATA3 1 J6 2 3 4 5 6 FL15 FL14 JP4 TD-A TD-B U25 SN75ALS172 JP3 DA T A 4 port IN/OUT signal is selected by the menu amo ng the output of IEC 61 162-1, NMEA V er .
APPENDIX AP-8 APB - Autopilot sentence dat a $--APB,A,A,x.x,a,N,A,A,x.x,a,c--c,x.x,a,x.x,a,a*hh<CR><LF> | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | +------- 13 | | | | | .
APPENDIX A P-9 BOD - Bearing, origin to destination $--BOD,x.x,T,x.x,M,c--c,c--c*hh<CR><LF> | | | | | | | | | | | | | +--------- 5 | | | | | +------------ 4 | | | | +----------------- 3 | | +--+--------------------- 2 +--+--------------------------- 1 1.
APPENDIX AP-10 BWR - Bearing, waypoint to range $--BWR,hhmmss.ss,llll.lll,a,yyyyy.yyy,a,x.x,T,x.x,M,x.x,N,c--c,a*hh<CR><LF> | | | | | | | | | | | | | | | | | | | | | | | | | | | +---- 9 | .
APPENDIX A P-1 1 DBT - Depth below transducer 1. Water depth, feet 2. Water depth, m 3. Water depth, fathoms 4. Checksum 4 3 2 1 $--DBT, x. x, f, x. x, M, x. x, F*hh<CR><LF> DPT - Depth $--DPT,x.x,x.x,x.x*hh<CR><LF> | | | | | | | +----- 4 | | +--------- 3 | +------------ 2 +---------------- 1 1.
APPENDIX AP-12 DTM - Datum reference $--DTM,ccc,a,x.x,a,x.x,a,x.x,ccc*hh<CR><LF> | | | | | | | | | | | | | | | | | +--- 7 | | | | | | | +------ 6 | | | | | | +---------- 5 | | | | +--+------------- 4 | | +---+------------------- 3 | +------------------------- 2 +---------------------------- 1 1.
APPENDIX A P-13 GGA -Global positioning system fix dat a $--GGA,hhmmss.ss,llll.lll,a,yyyyy.yyy,a,x,xx,x.x,x.x,M,x.x,M,x.x,xxxx*hh<CR><LF> | | | | | | | | | | | | | | | | | | | | | | | | | .
APPENDIX AP-14 GNS - GNSS fixed dat a $--GNS,hhmmss.ss,llll.lll,a,yyyyy .yyy ,a,c--c,xx,x.x,x.x,x.x,x.x,x.x*hh<CR><LF> | | | | | | | | | | | | | | | | | | | | | | | | | +--- 1 1 | | | | | .
APPENDIX A P-15 RMB - Recommended minimum navigation information $--RMB,A,x.x,a,c--c,c--c,llll.lll,a,yyyyy.yyy,a,x.x,x.x,x.x,A,a*hh<CR><LF> | | | | | | | | | | | | | | | | | | | | | | | | .
APPENDIX AP-16 RMC- Recommended minimum specific GPS/TRANSIT dat a $--RMC,hhmmss.ss,A,llll.lll,a,yyyyy .yyy ,a,x.x,x.x,xxxxxx,x.x,a,a*hh<CR><LF> | | | | | | | | | | | | | | | | | | | | | |.
APPENDIX A P-17 TLL - T arget latitude and longitude $--TLL,xx,llll.lll,a,yyyyy.yyy,a,c--c,hhmmss.ss,a,a*hh<CR><LF> | | | | | | | | | | | | | | | | | | | +--------- 8 | | | | | | | | +----.
APPENDIX AP-18 VDR – Set and drift $--VDR,x.x,T,x.x,M,x.x,N*hh<CR><LF> | | | | | | | | | | | | | +--------- 4 | | | | +--+----------- 3 | | +--+----------------- 2 +--+----------------------- 1 1. Direction, degrees true 2. Direction, degrees magnetic 3.
APPENDIX A P-19 WCV - W aypoint closure velocity $--WCV,x.x,N,c--c,a*hh<CR><LF> | | | | | | | | | | | +------- 4 | | | | +--------- 3 | | +--+----------- 2 +--+---------------- 1 1. Velocity component, knots 2. Waypoint identifier 3. Mode indicator(see note) 4.
APPENDIX AP-20 XTE - Cross-track error , measured $--XTE,A,A,x.x,a,N,a*hh<CR><LF> | | | | | | | | | | | | | +--------- 7 | | | | | +----------- 6 | | | | +------------- 5 | | | +--------------- 4 | | +------------------ 3 | +--------------------- 2 +----------------------- 1 1.
A P-21 TIME DIFFERENCES.
A P-7 GEODETIC CHART LIST 001 : WGS84 002 : WGS72 003 : TOKYO : Mean Va llue (Japan, Korea, and Okinawa) 004 : NORTH A MERICAN 1927 : Mean Va llue (CONUS) 005 : EUROPEAN 1950 : Mean V allue 006 : AUST.
AP-24 LORAN C CHAINS n i a h CI R G1 S2 S3 S4 S5 S c i f i c a P l a r t n e C0 9 9 41 19 2–– – t s a o C t s a E n a i d a n a C0 3 9 51 15 28 3–– ) a e r o K ( n o i L o d n a m m o C0 7 9.
A P-25 DECCA CHAINS n i a h C . o N n i a h Cn i a h C e d o c n o i t a c o Ln i a h C . o n n i a h Cn i a h C e d o c n o i t a c o L 1 0c i t l a B h t u o SA 0e p o r u E4 3o t n a KC 8n a p a J .
A -25 P ARTS LIST This equipment cont ains complex modules in which fault diagnosis and rep air down to component level ar e not practical (IMO A.694(17)/8.
A-34 Part s Location Display unit GR-7000A (Option) (08S0334) GN-8096 (20S0395) NP Board (20P8192) LCD EW50379FD W PNL Board (20P8148) Display unit, cover ope ned, GR-7000A installed A-26.
FURUNO GP-150/Dual SP-1 E4440S01A-M 060207 SPECIFICA TIONS OF GPS NA VIGA TOR GP-150/Dual 1 GPS RECEIVER 1.1 Receiving Frequency 1575.42 MHz 1.2 Tracking Code C/A code 1.3 Number of Channel GPS: 12 channels parallel, 12 satellites 1.4 Position Fixing Method All-in -view, 8-state Kalman filter 1.
FURUNO GP-150/Dual SP-2 E4440S01A-M 060207 3 INTERFACE 3.1 Number of Ports 4 3.2 Data Format IEC61162-1 (JUL-2000), NMEA0183 Ver1.5/2.0 IN: (DATA 1 &2*) AGFPA, DBT, DPT, MTW, TLL, HDG**, HDM**, HDT**, VBW**, VHW** (DATA 3) MOB from external device (contact closure), (DATA 4) DGPS correction data in RTCM SC-104 V2.
IN-1 INDEX A Anchor watc h alarm 7-2 Apportioning the Memory 2-5 Arrival Alarm 7-1 Automa tic testing 9- 6 B brilliance 1-3 C Canceling Destination 5-5 Centering C ursor P osition 2-2 Clearing the Mem.
INDEX IN-2 M Magnetic vari a tion 2-6 Mark Shape 3-2 mark connection lin e 3-2 Memory and I/O circuits test 9-5 MOB Mark 3-4 P Plotter 1 displ a y 1-4 Plotter 2 displ a y 1-4 [PLOT ON/OFF]key 2-2 Posi.
FURUNO EL E CT RI C C O., L TD . 9-5 2 Ashihara-Cho, Nishinomiya City, 662-8580, Hyogo, J apan Tel : + 81 798-65-2111 Fax: +8 1 798-65-4200 P ub NO . DOC-859 Declaration of c o n f o r m i t y We FURUNO ELECTR IC C O.
An important point after buying a device Furuno GP-150 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Furuno GP-150 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Furuno GP-150 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Furuno GP-150 you will learn all the available features of the product, as well as information on its operation. The information that you get Furuno GP-150 will certainly help you make a decision on the purchase.
If you already are a holder of Furuno GP-150, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Furuno GP-150.
However, one of the most important roles played by the user manual is to help in solving problems with Furuno GP-150. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Furuno GP-150 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
