Instruction/ maintenance manual of the product XG0224 Fujitsu
Go to page of 47
Hardware Guide TA41001-6348 XG0224 XG0224 XG0224 Hardware Guide Introductory.
XG0224 Hardware Guide 2 Pr eface Y ou have purchased the XG0224, a compact, 24 port 1 Gigabit Et hernet layer 2 switch that achieves unsurpassed standards of high throughput and low-latency performance. This manual explains the procedures required to install your XG0224 and should be read and understood before you start using your XG0224.
XG0224 Hardware Guide 3 LICENSE A GREEMENT Thank you for purchasing the XG Series switch product ("Hard ware") and accompanying softw a re ("Software," together with Hardware, collectively , re ferred to as "Product") manufactured by Fujitsu Limited ("Fujitsu").
XG0224 Hardware Guide 4 c. if in Fujitsu's sole judgment it is not commercially reasonabl e to perform either of the above options, subject to the limitation of liability set forth in subsection (2) above, Fujitsu shall pay for any dama ges Customer has incurred due to nonuse of the Software.
XG0224 Hardware Guide Contents 5 Contents Preface ..................................................... .................................................................. .........................................2 LICENSE AGREEMENT ...................
XG0224 Hardware Guide Contents 6 2.4 Connecting to a Setup PC ................................................. .................................................. ................... 41 2.5 Time Setting ................................................
XG0224 Hardware Guide 7 Or ganization and Usage of T his Manual This manual explains what you need to kno w before using this device. In addition, the README file on CD-ROM contains importa nt information. Y ou will also need to read the file. About This Manual This manual contains important informa tion required to use this device safely .
XG0224 Hardware Guide 8 T rademark Notification in This Manual Microsoft, MS-DOS, W indo ws, W indow s NT , W indows Server and W indows V ista are registered trademarks o f the Microsoft Corporation in the USA and other countries.
XG0224 Hardware Guide 9 How the Manuals for This Device Are Organized The manuals for this device are organized as follows. Use these manuals as necessar y . Manual Name Description Safety and Ins tallation Guide This manual describes the saf ety and installation.
XG0224 Hardware Guide 10 Saf ety Pr ecautions About W arning Descriptions This manual contains precautions that must be taken in orde r to use this device safely and prevent personal injury or property damage. Please fully understand the meanings and contents of the following descriptions and symbols when reading this manual.
XG0224 Hardware Guide 11 Always follow the instructions for safe use of t h is device. Indicat es that improper use can cause severe damage to person, resulting in serious injury or dea th. W arnings Do not disassemble, dismantle, modify or reproduce this device.
XG0224 Hardware Guide 12 Indicates that improper use can cause light or moderate injury . In addition, this symbol indicates a chance of dama ge to this device and other connected equipment. Cautions Do not touch this device for more than one minute while it is turned on.
XG0224 Hardware Guide 13 Notes on M aintenance • Customers should not repair this device. In the event of fa ilure, con sult with a Fujitsu service engineeror an engineer certified by Fujitsu for maintenance. • Do not dismantle or modify this device in any manner .
XG0224 Hardware Guide 14 Electromagnetic Comp atibility (USA) FCC Part-15 Class A Electromagnetic Comp atibility (CANADA) Industry Canada Interferen ce-Causing E quipment Standard ICES-003 Class A. This Class A digital appartatus complies with Canadian ICES-003.
XG0224 Hardware Guide 15 Laser Safety The XG0224 may be installed with optical transceiver modules (SFP and/or SFP+ modules), which emit invisible laser light.
XG0224 Hardware Guide 16 Notes on Use Before using this device, please read the fo llowing. • Customers are required to store an d maintain configura tion information for the device, after the configuration is complete.
Chap ter 1 Getting Star ted This chapter lists the items that should be in the product pa ckage, and describes the names and functions of the various components. 1.1 Items in the Package, Descriptions and Functions . . . . . . . . . . . . . . . . . . .
XG0224 Hardware Guide Chapter 1 Getting Started Items in the Package, Descriptions and Functio ns 18 1.1 Items in the P ackage, Descriptions and Functions Before proceeding, check all the items described below . 1.1.1 Part s List Please check that all of the followi ng parts are included in the package.
XG0224 Hardware Guide Chapter 1 Getting Started Items in the Package, Descriptions and Functio ns 19 1.1.2 Port Side • Console Port In order to set and operate the switc h, use the console cable and D-SUB9pin cro ss cable included in this package to connect to the PC.
XG0224 Hardware Guide Chapter 1 Getting Started Items in the Package, Descriptions and Functio ns 20 LED Det ails • Ready LED Indicates the operational state of the switch. • Error LED Indicates a compact flash mount/acc ess error occurred. • PSU LED Indicates the switch power supply status.
XG0224 Hardware Guide Chapter 1 Getting Started Items in the Package, Descriptions and Functio ns 21 LED Functions / Beha viors *) During system POST , the Ready LED blinks green at a 0.5 second interv al. When the switch is operating from the backup firmware image, the Ready LED blinks at a 1 second interval.
XG0224 Hardware Guide Chapter 1 Getting Started Items in the Package, Descriptions and Functio ns 22 1.1.3 Power Inlet Side • Power Inlet AC power inlet for the power cable provided. • Product Manufacturing Label This indicat es the model name, serial number , ma nufacturing date and Class 1 Laser Product, etc.
XG0224 Hardware Guide Chapter 1 Getting Started Items in the Package, Descriptions and Functio ns 23 1.1.4 T op Surface • W arning Label This label describes the safety measures you should take when using this product.
XG0224 Hardware Guide Chapter 1 Getting Started Options 24 1.2 Options 1.2.1 SFP Modules SFP modules (100BASE-FX/1000BASE-SX/1000BASE-LX /1000BASE-ZX/1000BASE-BX-D/1000BASE-BX-U) can be used. Precautions • T urn the switch powe r off to install a SFP module.
XG0224 Hardware Guide Chapter 1 Getting Started Options 25 1.2.4 Exp ansion Card The following describes the available ex pansion card options. The optional expansion card is installed in the expansion slot on the port side of the switch. The following details the functions/behaviors of ea ch type of expansion card.
XG0224 Hardware Guide Chapter 1 Getting Started Options 26 CX4 Exp ansion Card • CX4 Link/Act LEDs Indicates CX4 port link status / communication status.
Chap ter 2 Installa tion This chapter describes how to install the switch and connect it to Console PC. 2.1 Requirement s for Installation Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 2.1.1 Inst allation Requirements .
XG0224 Hardware Guide Chapter 2 Installation Requirements for Installation Environm ent 28 2.1 R equir ements f or Installa tion En vir onment Before installing the switch, please check the following: • Make sure that the switch and all the other options shown in this document are available for installation.
XG0224 Hardware Guide Chapter 2 Installation Requirements for Installation Environm ent 29 Inst allation Condition Check List Check the following items. Check Ite m Check Result Nothing is put on the switch. V ents are not obstruct ed. The switch is not located on the table or not stuck on another switch.
XG0224 Hardware Guide Chapter 2 Installation Requirements for Installation Environm ent 30 2.1.2 S p ace Requirement s When installing the switch and providing maintena nce, ensure the space below is maintained.
XG0224 Hardware Guide Chapter 2 Installation Installation 31 2.2 Installa tion This section describes how to install the switch. 2.2.1 Inst allation of the Switch The following describes how to install. Inst allation on 19” Rack The switch can be installed and opera ted in the EIA standard 19” ra ck.
XG0224 Hardware Guide Chapter 2 Installation Installation 32 2. Put rack mounting brackets on the switch using M3 Co untersunk S crews (Qty 8). T wo ways below are possible for putting on rack mounting brackets. Precautions When putting on rack mounting bra ckets, make sure to use special screws included in the 19” rac k brackets set.
XG0224 Hardware Guide Chapter 2 Installation Installation 33 2.2.2 Inst allation of Extension Card The extension cards can be installed to the switch as optional. Below describes how to install each extension card. Inst allation of SFP+ Extension Card / CX4 Extension Card Below describes the case of SFP+ Extension card.
XG0224 Hardware Guide Chapter 2 Installation Installation 34 Removing SFP+ Extension Card / CX4 Extension Card 1. T urn off the power of the switch. Caution If the extension card is removed when the po wer is on, the Check LED will light up and the switch will go into trouble st ate.
XG0224 Hardware Guide Chapter 2 Installation Connecting the Equipment 35 2.3 Connecting the Equipment W e recomm end discharging static electri city of tw isted pair cable before connecting it to the switch. Also see below for how to install the compact flash card.
XG0224 Hardware Guide Chapter 2 Installation Connecting the Equipment 36 Cleaning of Optical Connector 1. Remove the connector gu ard cap of optical fi ber part, and check the connector end face. If the end face is not clean, clean it with a reel type fiber cleaner .
XG0224 Hardware Guide Chapter 2 Installation Connecting the Equipment 37 2. 3 .3 Connecting T wisted Pair Ca ble / SFP Module / SFP+ Module / CX4 Cable The following describes how to connect twisted pair cable, SFP module, SFP+ module, and CX4 cable. Use straight cable when connecting with routers and terminals.
XG0224 Hardware Guide Chapter 2 Installation Connecting the Equipment 38 Connecting SFP Module Firmly install SFP module to SFP sl ot and lock module to the switch. Caution Make sure to turn off the power when inserting and pulling out the SFP module.
XG0224 Hardware Guide Chapter 2 Installation Connecting the Equipment 39 Connecting SFP+ Module Firmly install SFP+ module to SFP+ slot and lock module to the swit ch. Caution Make sure to turn off the power when inserting and pulling out the SFP+ module.
XG0224 Hardware Guide Chapter 2 Installation Connecting the Equipment 40 Connecting CX4 Cable Firmly install CX4 cable to CX4 expa nsion card port and l ock the cab le.
XG0224 Hardware Guide Chapter 2 Installation Connecting to a Setup PC 41 2.4 Connecting to a Setup PC This is to connect a set up PC to the console port of the switch using RS232C cable. Necessary Hardware / Sof tware Please prepare the ha rdware & software specified below to connect to the switch.
XG0224 Hardware Guide Chapter 2 Installation Connecting to a Setup PC 42 T urn on the Power Caution • Please use the power cable included in this product. Also, please do NOT use this power cable on other products. • If the power outlet does not match with the power cable plug, please use the change plug adapter .
XG0224 Hardware Guide Chapter 2 Installation Connecting to a Setup PC 43 Prep are a Setup PC Log on using the terminal software . 1. S tart up the terminal software by using the set up PC. 2. Set the setting conditio ns to the following; Please refer to the termin al software manual for instructions on setting conditions.
XG0224 Hardware Guide Chapter 2 Installation Time Setting 44 2.5 Time Setting Make sure to set up the time before you do other settings of the switch. The time is not set at the initial timing of purchase. Please refer below command for setting up time manually using con sole or telnet.
XG0224 Hardware Guide Chapter 2 Installation Set up IP address 45 2.6 Set up IP addr ess Please set the IP address at times when it is required. Eg. When setting the switch through www browser or insta lling a firmware from the initial state of the purchase.
XG0224 Hardware Guide Index 46 Inde x Number 10/100/1000BASE-T Port .......... ........................ ...... 19 C CD-ROM ........... .......... .......... ............ .......... .......... ... 18 Check LED ........... ............ .................
XG0224 Hardware Guide T A41001-6348 Issued on November , 2009 Issued by FUJITSU LIMITED • The contents may be revised without prior notice. • Fuji tsu assumes no liability for damages to third party copyrights or other right s arising from the use of any information in this manual.
An important point after buying a device Fujitsu XG0224 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fujitsu XG0224 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fujitsu XG0224 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fujitsu XG0224 you will learn all the available features of the product, as well as information on its operation. The information that you get Fujitsu XG0224 will certainly help you make a decision on the purchase.
If you already are a holder of Fujitsu XG0224, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fujitsu XG0224.
However, one of the most important roles played by the user manual is to help in solving problems with Fujitsu XG0224. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fujitsu XG0224 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
