Instruction/ maintenance manual of the product C141-E280 Fujitsu
Go to page of 12
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dime nsions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the disk drive. All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions.
3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be mounted in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero.
Installation Conditions (3) Limitation of mounting Note) These dimensions are recommended va lues; if it is not possible to satisfy them, contact us. Screw Screw Details of A 3.0 or less 3.0 or less Frame of system cabinet Frame of system cabinet B PCA A 2 2.
3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to close during mounting. Locating of breather hole is shown as Figure 3.3.
Installation Conditions (4) Ambient temperature The temperature conditions for a disk dr ive mounted in a cabinet refer to the ambient temperature at a point 3 cm from the disk drive. The ambient temperature must satisfy the temperature conditions de scribed in Section 1.
3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. Mounting screw hole Mounting screw hole Cable connection Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speaker s.
Installation Conditions - General notes ESD mat Shock absorbin g mat Wrist strap Use the Wrist stra p . Place the shock absorbing mat on the operation table, and place ESD mat on it. Do not hit HDD each other. Do not stack when carr y in g . Do not p lace HDD verticall y to avoid fallin g down.
3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals. SATA inte rface and power connectors PCA Figure 3.
Installation Conditions 3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of the SA TA interface connector and pin numbers. Power s uppl y seg ment P1 pins in the po w er supply se gment V iew fro m the connecto r side V iew from the PCA side Si g nal se g ment S1 pins in the si g nal s e g m e n t Figure 3.
3.3 Connections with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be compliant with the Serial ATA Revision 2.
This page is intentionally left blank..
An important point after buying a device Fujitsu C141-E280 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fujitsu C141-E280 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fujitsu C141-E280 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fujitsu C141-E280 you will learn all the available features of the product, as well as information on its operation. The information that you get Fujitsu C141-E280 will certainly help you make a decision on the purchase.
If you already are a holder of Fujitsu C141-E280, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fujitsu C141-E280.
However, one of the most important roles played by the user manual is to help in solving problems with Fujitsu C141-E280. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fujitsu C141-E280 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
