Instruction/ maintenance manual of the product KFC-1 SMS Frymaster
Go to page of 42
Frymaster, a member of the Co mmercial Food Equipment Serv ice Association, recommends using CFESA Certified Tec hnicians. 24-Hour Service Hotline 1-800-551-8633 FEB 2001 8195733 KFC-1 SMS Cooking Com.
1- 1 KFC-1 SMS COMPUTER CHAPTER 1: IMPORTANT INFORMATION 1.1 General The KFC-1 SMS Cooking Computer is designed to operate with both full- and split-pot fryers. For a full-pot fryer, turn the computer on by pressing either switch. For split-pot fryers, press the left switch to operate the left pot and the right switch to operate the right pot.
1- 2 1.3 KFC-1 SMS Computer Controls KFC-1 SMS Computer Button Function On/Off Turns the fryer ON and OFF. For a full-pot fryer, press either ON/OFF switch to turn the computer on. For a split-pot fryer, press the left ON/OFF switch to operate the left pot and press the right ON/OFF switch to operate the right pot.
1- 3 1.3 KFC-1 SMS Computer Controls (cont.) Button Function Program Scan Shows the remaining cook time for other active cook cycles when operating in the multiple cook cycle mode. In programming mode, this button activates programming mode, and advances through the programming steps.
1- 4 1.4 Morning (AM) Polishing Cycle 1 2 3 4 5 Computer display changes to PLSH. When the fryer reaches filtration setpoint, the display alternates between START and PLSH. Press EXIT/COOL FILTER button on computer face. Assemble filter. Sprinkle 8 ounces of filter powder over filter paper in filter pan.
1- 5 1.4 Morning (AM) Polishing Cycle (cont.) 6 Computer counts down. Polishing lasts 30 minutes. 7 8 9 10 Computer displays FILL and an alarm sounds. Press Exit/Cool Filter to shut off alarm. Cool appears in right display. Press EXIT/COOL FILTER button Computer displays oil temperature and fryer heats to setpoint.
1- 6 1.5 Afternoon (PM) Polishing Cycle 1 Assemble filter. Sprinkle filter powder over filter paper in filter pan. 2 3 4 At 2 p.m. an alarm sounds and computer display alternates between START and PLSH. Press EXIT/COOL FILTER button on computer face to shut off alarm.
1- 7 1.5 Afternoon (PM) Polishing Cycle (cont.) 5 Computer counts down. 6 7 8 9 At the end of the polishing cycle, the computer displays FILL and an alarm sounds. Press Exit/Cool Filter to shut off alarm. COOL appears in right display. Computer displays LOW and fryer heats to setpoint.
1- 8 1.6 Delaying Afternoon (PM) Polishing Cycle 1 2 3 4 5 Press any program button. The fryer will cook normally until the preprogrammed delay period expires. The polish can only be delayed once. Polish must be performed within three-hour period or the controller will go into polish lockout.
1- 9 1.7 Using Polish Now Feature 1 2 Assemble filter. Sprinkle 8 ounces of filter powder over filter paper in filter pan. 3 4 Computer displays START and PLSH. 5 Computer display alternates between DYPL and temperature display, indicating the polish cycle has been delayed.
1- 10 1.7 Using Polish Now Feature (cont.) 6 7 Computer counts down 8 9 10 Computer displays FILL and an alarm sounds. Press Exit/Cool Filter to cancel alarm. Press EXIT/COOL FILTER button to exit COOL mode. Open drain valve. Turn pump on. Computer displays PLSH 30:00 to polish shortening for 30 min.
1- 11 1.7 Using Polish Now Feature (cont.) 11 1.8 Operating Instructions 1 2 Computer displays LOW and fryer heats to setpoint. Fryer displays DROP when oil/shortening temperature is at setpoint and ready to cook. Fryer is heating. Turn the fryer ON for cooking operations.
1- 12 1.8 Operating Instructions (cont.) 3 4 5 6 Computer displays LOW. Select a product, i.e. product 4. Fryer heats to preset temperature. Oil temperature at 255 °F (124 °C). Actual oil temperature will be displayed until oil temperature is within ±2 °F (±1 °C) of setpoint temperature (SET--TEMP).
1- 13 1.8 Operating Instructions (cont.) 7 8 9 Computer displays DONE and an alarm sounds. Cook cycle is complete. Pressing the flashing product number will stop the alarm and return the fryer to selected standby cycle mode (COOL, SET--TEMP, FILTER).
1- 14 1.8 Operating Instructions (cont.) 10 11 To begin the filtering cycle, close drain valve. Computer will display FILL. Turn filter pump on and allow frypot to refill. After bubbles appear in frypot for 15 seconds, close return valve and turn filter pump OFF.
2- 1 KFC-1 SMS COMPUTER CHAPTER 2: PROGRAMMING INSTRUCTIONS 2.1 General The KFC-1 SMS Computer arrives with a default program loaded in its nonvolatile memory. Nonvolatile memory retains product-cooking instructions so this information will not be lost if there is a power surge or outage.
2- 2 2.2.1 Programming for Extra Tasty Crispy Chicken Enter Programming Mode as outlined in Section 2.2 1 2 3 4 Computer displays PRODUCT. Press button #1 for product. Computer displays HEADS. Press button #4 to set head count to "4". Press ENTER for next step.
2- 3 2.2.1 Programming for Extra Tasty Crispy Chicken (cont.) 5 6 7 8 Computer displays SET--TEMP. Enter 3 4 0, in that sequence. Press ENTER to save 340 °F (171 °C) as set-- temp for interval #1. Computer displays FLEX. Press button #0 to set straight time cooking mode.
2- 4 2.2.1 Programming for Extra Tasty Crispy Chicken (cont.) 9 10 11 12 Computer displays SET--TEMP. Enter 3 1 0, in that sequence. Press ENTER to save 310 °F (154 °C) as set-- temp for interval #2. Computer displays FLEX. Press button #0 to set straight time cooking mode.
2- 5 2.2.1 Programming for Extra Tasty Crispy Chicken (cont.) 13 14 15 16 Computer displays SET--TEMP. Enter 3 3 0, in that sequence. Press ENTER to save 330 °F (166 °C) as set-- temp for interval #2. Computer displays FLEX. Press button #0 to set straight time cooking mode.
2- 6 2.2.1 Programming for Extra Tasty Crispy Chicken (cont.) 17 18 Computer displays PREALM 2. Enter 0 0, in that sequence. Press PROG SCAN button to advance to Exit Cycle program mode. Computer displays EX-CYCLE in the left display and SET--TEMP in the right display.
2- 7 2.2.1 Programming for Extra Tasty Crispy Chicken (cont.) 19 20 21 Computer displays NUM FILT. Press button #1 to select Filter Lockout mode of "1". Press ENTER to set Filter Lockout Mode of "1". Computer displays INTERVAL in the left display and PROD 1 in the right display.
2- 8 2.2.2 Programming for Colonel’s Crispy Strips Enter Programming Mode as outlined in Section 2.2 1 2 3 4 Computer displays PRODUCT. Press button #2 for product. Computer displays HEADS. Press button #0 to set head count to "0". Press ENTER for next step.
2- 9 2.2.2 Programming for Colonel’s Crispy Strips (cont.) 5 6 7 8 Computer displays SET--TEMP. Enter 3 4 0, in that sequence. Press ENTER to save 340 °F (171 °C) as set-- temp for interval #1. Computer displays FLEX. Press button #3 to set flex mode = "3".
2- 10 2.2.2 Programming for Colonel’s Crispy Strips (cont.) 9 10 11 12 Computer displays PREALM 2. Press PROG SCAN button to advance to Exit Cycle program mode. Computer displays EX-CYCLE in the left display and SET--TEMP in the right display. Press ENTER button to save default setting of SET--TEMP.
2- 11 2.2.3 Programming for Hot Wings/Hot BBQ Wings Enter Programming Mode as outlined in Section 2.2 1 2 3 4 Computer displays PRODUCT. Press button #3 for product. Computer displays HEADS. Press button #0 to set head count to "0". Press ENTER for next step.
2- 12 2.2.3 Programming for Hot Wings/Hot BBQ Wings (cont.) 5 6 7 8 Computer displays SET--TEMP. Enter 3 4 0, in that sequence. Press ENTER to save 340 °F (171 °C) as set-- temp for interval #1. Computer displays FLEX. Press button #3 to set flex mode = "3".
2- 13 2.2.3 Programming for Hot Wings/Hot BBQ Wings (cont.) 9 10 11 12 Computer displays PREALM 2. Press PROG SCAN button to advance to Exit Cycle program mode. Computer displays EX-CYCLE in the left display and SET--TEMP in the right display. Press ENTER button to save default setting of SET--TEMP.
2- 14 2.2.4 Programming for Potato Wedges Enter Programming Mode as outlined in Section 2.2 1 2 3 4 Computer displays PRODUCT. Press button #4 or #5 for product. Computer displays HEADS. Press button #0 to set head count to "0". Press ENTER for next step.
2- 15 2.2.4 Programming for Potato Wedges (cont.) 5 6 7 8 Computer displays SET--TEMP. Enter 3 4 0, in that sequence. Press ENTER to save 340 °F (171 °C) as set-- temp for interval #1. Computer displays FLEX. Press button #3 to set flex mode = "3".
2- 16 2.2.4 Programming for Potato Wedges (cont.) 9 10 11 12 Computer displays PREALM 2. Press PROG SCAN button to advance to Exit Cycle program mode. Computer displays EX-CYCLE in the left display and SET--TEMP in the right display. Press ENTER button to save default setting of SET--TEMP.
2- 17 2.2.5 Programming for Sandwiches/Filets Enter Programming Mode as outlined in Section 2.2 1 2 3 4 Computer displays PRODUCT. Press button #6 or #7 for product. Computer displays HEADS. Press button #0 to set head count to "0". Press ENTER for next step.
2- 18 2.2.5 Programming for Sandwiches/Filets (cont.) 5 6 7 8 Computer displays SET--TEMP. Enter 3 4 0, in that sequence. Press ENTER to save 340 °F (171 °C) as set-- temp for interval #1. Computer displays FLEX. Press button #3 to set flex mode = "3".
2- 19 2.2.5 Programming for Sandwiches/Filets (cont.) 9 10 11 12 Computer displays PREALM 2. Press PROG SCAN button to advance to Exit Cycle program mode. Computer displays EX-CYCLE in the left display and SET--TEMP in the right display. Press ENTER button to save default setting of SET--TEMP.
2- 20 2.2.6 Programming for Popcorn Chicken Enter Programming Mode as outlined in Section 2.2 1 2 3 4 Computer displays PRODUCT. Press button #8 for product. Computer displays HEADS. Press button #0 to set head count to "0". Press ENTER for next step.
2- 21 2.2.6 Programming for Popcorn Chicken (cont.) 5 6 7 8 Computer displays SET--TEMP. Enter 3 4 0, in that sequence. Press ENTER to save 340 °F (171 °C) as set-- temp for interval #1. Computer displays FLEX. Press button #3 to set flex mode = "3".
2- 22 2.2.6 Programming for Popcorn Chicken (cont.) 9 10 11 12 Computer displays PREALM 2. Press PROG SCAN button to advance to Exit Cycle program mode. Computer displays EX-CYCLE in the left display and SET--TEMP in the right display. Press ENTER button to save default setting of SET--TEMP.
3- 1 KFC-1 SMS COMPUTER CHAPTER 3: ADDITIONAL COMPUTER SETTINGS 3.1 Programming for Shortening Management Listed below are procedures for initiating the Shortening Management System software and setting local time, daylight savings time and stagger between polishings.
3- 2 3.2 Setting Daylight Savings Time/Stagger Between Polishings 1 2 3 Enter Code #: 1 6 5 5, in that sequence. Press ON/OFF button to turn computer OFF. Press PROG SCAN button to enter CODE. Computer displays CODE in the left display and (Blank) in the right display.
3- 3 4 3.3 Setting Local Time 1 2 Enter Code #: 2 0 0 0, in that sequence. Press ON/OFF button to turn computer OFF. Press PROG SCAN button to enter CODE. Computer displays CODE in the left display and (Blank) in the right display. As each number is entered, dashes appear in the right display.
3- 4 3 4 Example: Computer displays SET TIME in left display and 00:00 in right display. Enter correct time (military style) using product selection keys. To enter 8:00 AM, enter 0 8 0 0, in that sequence. Press ENTER to set time. To enter 4:00 PM, enter 1 6 0 0, in that sequence.
Frymaster, L.L.C. 8700 Line Avenue, Shreveport, Louisiana USA 71106 Service Center (800) 551-8633 or (318) 865-1711 Printed in the United States of America 819-5733 English 02/01.
An important point after buying a device Frymaster KFC-1 SMS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Frymaster KFC-1 SMS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Frymaster KFC-1 SMS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Frymaster KFC-1 SMS you will learn all the available features of the product, as well as information on its operation. The information that you get Frymaster KFC-1 SMS will certainly help you make a decision on the purchase.
If you already are a holder of Frymaster KFC-1 SMS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Frymaster KFC-1 SMS.
However, one of the most important roles played by the user manual is to help in solving problems with Frymaster KFC-1 SMS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Frymaster KFC-1 SMS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
