Instruction/ maintenance manual of the product 2008 Taurus Ford
Go to page of 328
Introduction 4 Instrument Cluster 10 W arning lights and chimes 10 Gauges 14 Entertainment Systems 16 How to get going 16 AM/FM stereo with CD 20 AM/FM stereo with in-dash six CD 28 Auxiliary input ja.
Locks and Security 121 Keys 121 Locks 122 Anti-theft system 135 Seating and Safety Restraints 141 Seating 141 Safety restraints 149 Airbags 162 Child restraints 176 Tires, Wheels and Loading 189 T ire.
Customer Assistance 267 Reporting safety defects (U.S. only) 273 Reporting safety defects (Canada only) 274 Cleaning 275 Maintenance and Specifications 282 Engine compartment 284 Engine oil 286 Batter.
CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
Special instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. Please read the section Airbag supplemental restraint system (SRS) in the Seating and Safety Restraints chapter . Failure to follow the specific warnings and instructions could result in personal injury .
other government authorities or other third parties acting with lawful authority . Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada. Cell phone use The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emper.
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulbs work.
Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Check fuel cap (if equipped): Illuminates when the fuel cap may not be properly installed.
Airbag readiness: If this light fails to illuminate when the ignition is turned to ON, continues to flash or remains on, have the system serviced immediately by your authorized dealer . A chime will also sound when a malfunction in the supplemental restraint system has been detected.
Low fuel (if equipped): Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter). Speed control: Illuminates when the speed control is engaged.
GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating.
Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The FUEL icon and arrow indicates which side of the vehicle the fuel filler door is located.
AUDIO SYSTEMS Quick start — How to get going Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road.
Listening to satellite radio (if equipped) 1. If the audio system is turned off, press VOL-PUSH to turn the radio on. T urn VOL-PUSH to adjust the volume. Note: The system may take a few moments to turn on. 2. Press AUX repeatedly to cycle through auxiliary audio sources.
For a single CD system, if a disc is not already loaded, insert only one, label side up into the CD slot. LOADING CD and READING DISC will appear in the display . The first track on the disc will begin playing. For an in-dash six CD system, if a disc is not already loaded, press LOAD.
Press SHUFFLE to engage shuffle mode. SHUFFLE ON will appear in the display . If you wish to engage shuffle mode right away , press SEEK to begin random play . Otherwise, random play will begin when the current track is finished playing. CD SHUF will appear in the display .
AM/FM Single CD/MP3 satellite compatible sound system (if equipped) Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road.
Category Mode under Menu for further information. Satellite radio is available only with a valid SIRIUS subscription. Check with your authorized dealer for availability . 2. (Phone): Y our vehicle may be equipped with SYNC which has special phone features.
Rock, News, etc.) Press OK when the desired category appears in the display . After a category is selected, press SEEK to search for that specific category of channels only (i.e. ROCK). Y ou may also select CA TEGORY ALL to seek all available SIRIUS categories and channels.
AUTOSET : Press MENU until the display reads AUTOSET . Autoset allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2. Use / to turn on/off. When the six strongest stations are filled, the station stored in preset 1 will begin playing.
Recommended level is 1–3; SPEED OFF turns the feature off and level 7 is the maximum setting. TRACK/FOLDER MODE: A vailable only on MP3 discs in CD mode. In track mode, press SEEK, SEEK to scroll through all tracks on the disc In folder mode, press SEEK, SEEK to scroll through tracks within the selected folder .
(Jazz, Rock, News, etc.), press SEEK, SEEK to seek to the previous/next channel in the selected category . Press and hold SEEK, SEEK to fast seek through the previous /next channels. In TEXT MODE, press SEEK, SEEK to view the previous/additional display text.
10. FF (Fast forward): Press FF to manually advance in a CD/MP3 track. 11. REW (Rewind): Press REW to manually reverse in a CD/MP3 track. 12. Memory presets: T o set a station, select the desired frequency band, AM, FM1 or FM2. T une to the desired station.
14. AM/FM: Press to select AM/FM1/FM2 frequency band. 15. ON/OFF/V olume: Press to turn ON/OFF . T urn to increase/decrease volume. Note: If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Premium/Audiophile AM/FM in-dash six CD/MP3 satellite compatible sound system (if equipped) Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road.
In CA TEGOR Y mode (if equipped), press to scroll through the list of available SIRIUS channel categories. Satellite radio is available only with a valid SIRIUS radio subscription. Check with your authorized dealer for availability . 2. (Phone): Y our vehicle may be equipped with the SYNC system which has special phone features.
• CA TEGOR Y : Press OK to enter category mode. Press / to scroll through the list of available SIRIUS channel Categories (Pop, Rock, News, etc.) Press OK when the desired category appears in the display . After a category is selected, press SEEK to search for that specific category of channels only (i.
Satellite radio is available only with a valid SIRIUS radio subscription. Check with your authorized dealer for availability . AUTOSET : Press MENU until the display reads AUTOSET . Autoset allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2.
The default setting is off; increasing your vehicle speed will not change the volume level. Adjust 1–7: Increasing this setting from 1 (lowest setting) to 7 (highest setting) allows the radio volume to automatically change slightly with vehicle speed to compensate for road and wind noise.
5. SEEK : In radio mode, press / to access the previous/next strong station. In CD mode, press / to access the previous/next CD track. In satellite radio mode (if equipped) , press SEEK, SEEK to seek to the previous/next channel. If a specific category is selected, (Jazz, Rock, News, etc.
8. FOLDER : In folder mode, press FOLDER to access next folder on MP3 discs, if available. 9. FOLDER: In folder mode, press FOLDER to access the previous folder on MP3 discs, if available. 10. FF (Fast forward): Press FF to manually advance in a CD/MP3 track.
In TEXT MODE, sometimes the display requires additional text to be displayed. When the “>” indicator is active, press SEEK to view the additional display text. When the “<” indicator is active, press SEEK to view the previous display text.
If there is only one disc present in the system, press . T o auto eject up to 6 CDs, press and hold until the system begins ejecting all loaded discs. If the discs are not removed, the system will reload the discs. 19. CD slot: Insert a CD/MP3 label side up.
4. T urn the radio on, using either a tuned FM station or a CD loaded into the system. Adjust the volume to a comfortable listening level. 5. T urn the portable music player on and adjust the volume to 1/2 the volume. 6. Press AUX on the vehicle radio repeatedly until LINE IN appears in the display .
USB port (if equipped) Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation of their vehicle.
CD/CD player care Do: • Handle discs by their edges only . (Never touch the playing surface). • Inspect discs before playing. • Clean only with an approved CD cleaner . • W ipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time.
CDs with homemade paper (adhesive) labels should not be inserted into the CD player as the label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs.
Sample MP3 structure If you are burning your own MP3 discs, it is important to understand how the system will read the structures you create. While various files may be present, (files with extensions other than mp3), only files with the .mp3 extension will be played.
• T errain: Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with your reception. • Station overload: When you pass a ground based broadcast repeating tower , a stronger signal may overtake a weaker one and result in an audio mute.
Radio Display Condition Action Required ACQUIRING Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly .
Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly . NO TEXT Category information not available. Category information not available at this time on this channel.
Y our vehicle may be equipped with a Family Entertainment System (FES) which allows you to listen to audio CDs, MP3 discs, watch DVDs and to plug in and play a variety of standard video game systems. The DVD player is capable of playing standard DVDs, CDs, MP3s and is compatible with CD-R/W , CD-R and certain CD-ROM media.
Press the power button to turn the system OFF . The indicator light will turn off indicating the system is off. Note: The audio from the DVD system will play over all vehicle speakers and can be adjusted by the radio volume control. T o play a CD in the DVD system: The DVD system can play audio CDs, CD-R and CD-R/W , CD-ROM and video CDs.
3. The disc will begin to play and the ’MP3 Audio Disc’ screen will display and allow you to access the COMPRESSION, SHUFFLE, SCAN and FOLDER MODE features.
T o listen to audio over the headphones (Dual play mode): 1. Y ou may listen to channels A and B over wired or wireless headphones. Refer to Using the infrared wireless headphones and Using wired headphones for further information. • Black (4) — wired headphone output (wired headphones not included) 2.
2. Adjust the volume levels using the volume controls on the DVD system. T o adjust display brightness: T o decrease/increase the brightness level on the display screen, press the brightness control on the DVD system. A display will appear at the bottom of the screen indicating the brightness level.
Note: Headphone A can access any possible media (AM, FM1, FM2, SA T (if equipped), CD, DVD, DVD-AUX). Headphone B can only access DVD and DVD-AUX. For further information, refer to Single play/Dual play later in this section. 2. / (Stop/Eject): Press once to stop and press a second time to eject a disc from the DVD system.
9. LCD screen: The eight inch diagonal screen rotates down to view and up into housing to store when not in use. Ensure that the screen is latched into the housing when being stored. 10. V olume: When in Single Play , press to increase ( ) or decrease ( ) the volume over all speakers.
15. ENTER: Press to select/confirm the current selection. 16. Cursor /Brightness controls: Use the cursor controls to make various selections when in any menu. When not in a menu, and in DVD mode, press / to adjust the brightness. A display bar will appear at the bottom of the screen indicating the brightness levels.
1. Power control: Press to turn the FES (Family Entertainment System) ON/OFF . 2. Cursor controls: Use in various active menus to advance the cursor up/down/left/right. When not in a Menu, the left and right cursor controls decrease and increase the display brightness.
(W ireless headphone volume is controlled with the rotary dial on the right ear piece.) 8. Fast Forward/Next: In DVD mode, press and hold for a quick advance within the DVD. Press and release to advance to the next chapter . In CD/MP3 mode, press to access the next track.
23. ILLUMINA TION : Press to illuminate the remote control and backlight all of the buttons. Battery replacement Batteries are supplied with the remote control unit. Since all batteries have a limited shelf life, replace them when the unit fails to control the DVD player .
Y our FES system is equipped with two sets of battery powered, infrared wireless headphones. T wo AAA batteries are needed to operate the headphones. (Batteries are included.) Additional infrared wireless headphones may be purchased for use with the system.
T o install the batteries, remove the screw at the bottom of the cover . Then, lightly press down on top and slide the cover off. When replacing the batteries, use two new batteries (alkaline recommended) and install them with the correct orientation as indicated in the battery housing.
T o operate the headphones: • Press POWER on the ear piece to turn on the headphones. A red indicator light will illuminate indicating the headphones are ON. Press POWER again to turn the headphones off. • Adjust the headphones to comfortably fit your head using the headband adjustment.
Wired headphones Do not leave children unattended in the vehicle and do not let children operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may become entangled in the cords and seriously injure themselves.
Single Play: Single play consists of all occupants in the vehicle listening to the same playing media over the front and rear speakers. When the DVD system is on, and the same source is playing through the front and rear speakers, SINGLE PLA Y will appear in the front radio display .
Operation with an aftermarket audio system (Headphone only mode) When the Family Entertainment System (FES) detects that the original radio supplied by Ford Motor Company has been removed from the vehicle, the Family Entertainment System will work in a state referred to as “Headphone Only Mode”.
This is disc dependent — some DVD discs may have more viewing angles to select from. Once you have made your selection, press ENTER to confirm. The system default is Angle 1. Aspect ratio Select ASPECT RA TIO to select the viewing size and shape of the video displayed on the LCD screen.
Once you have made your selection, press ENTER to confirm. The system default is English. Subtitles Select SUBTITLES to turn the subtitle option on or off. The system default is OFF . Once you have made your selection, press ENTER to confirm. This is disc dependent.
SCAN. Once you have highlighted the desired track or function, press ENTER on the DVD bezel to confirm your selection. COMP (Compression): Compression brings soft and loud CD passages together for a more consistent listening level when in CD mode. Press to turn the feature ON/OFF SHUFFLE: Press to hear all tracks on the current CD in random order .
• Disc finalization — The disc may be left open for the purpose of adding sessions to it at a later time, but be sure to close each session or the disc will not play .
with homemade paper (adhesive) labels should not be inserted into the FES DVD system. The label may peel and cause the CD or DVD to become jammed. It is recommended that homemade CDs or DVDs be identified with permanent felt tip marker rather than adhesive labels.
2. Press and hold the reverse or advance button to enter into slow play mode. Once in slow play mode, press and release the reverse or advance button repeatedly to cycle through 1/4 and 1/2. These will display on the status bar on top of the screen as the screens cycle through at this rate.
The B headphone jack (5) is located on the right side of the DVD system. Plug in wired headphones (not included) here. Note: The B headphones can only access DVD and AUX modes. They cannot access radio sources. Audio displays Y our DVD system interacts closely with the front audio system.
FULL (enabled): The FES has control over the primary (speaker) and secondary (headphone) audio sources. LOCAL : The FES has control over the secondary source (headphones) only . The radio will ignore button presses that affect the primary (speaker) audio source.
use this product in any commercial (i.e. revenue generating) real time broadcasting (terrestrial, satellite, cable and /or any other media) broadcasting/streaming via internet, intranets and/or other networks or in other electronic content distribution systems, such as pay-audio or audio-on-demand applications.
Be sure to review User Manuals for video games and video game equipment when used as auxiliary inputs for your Family Entertainment System (FES). Do not operate video games or video equipment if the power cords and/or cables are broken, split or damaged.
• locations where strong magnetic fields are generated. T emperature extremes When the vehicle is parked under direct sunlight or in an extremely cold place for a long period of time, wait until the cabin temperature of the vehicle is at normal temperature before operating the system.
While operating in Headphone Only Mode, the system will have limited functionality . • The system will only output audio to the headphones. It will not be capable of providing audio to the speakers. • The available sources in FES Headphone Only Mode are DVD-DISC and DVD-AUX, regardless of headphone channel (A or B).
MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. T emperature selection: Controls the temperature of the airflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in the vehicle.
6. Fan speed adjustment: Controls the volume of air circulated in the vehicle. Operating tips • T o reduce fog build up on the windshield during humid weather , place the air flow selector in the position. • T o reduce humidity build up inside the vehicle: do not drive with the airflow selector in the O (OFF) or with recirculated air engaged.
DUAL ZONE AUTOMATIC T EMPERATURE CONTROL (IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from the windshield.
8. : Distributes air through the instrument panel and floor vents. 9. : Distributes air through the instrument panel vents. 10. Manual override controls: Allows you to manually select where airflow is directed. T o return to full automatic control, press AUTO.
Dual Zone Automatic T emperature Control with heated seats (if equipped) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from the windshield. T o exit select another mode. 2.
8. Airflow direction control: Press to toggle through the air distribution modes listed below . The selected mode will be shown in the display . : Distributes air through the instrument panel and center console vents (if equipped). : Distributes air through the instrument panel, floor and center console vents (if equipped).
• Do not put objects under the front seats that will interfere with the airflow to the back seats. • Remove any snow , ice or leaves from the air intake area at the base of the windshield. • For maximum cooling performance (MAX A/C): In AUTO mode, press AUTO control and set to desired temperature.
HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
3. T urn the ignition switch to RUN and then back to LOCK. 4. T urn the headlamp switch to the autolamp position. The headlamps will turn on. 5. W ait the desired amount of time for the exit delay you want (up to three minutes), then turn the headlamp switch to .
Flash to pass Pull toward you to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) T urns the headlamps on with a reduced output.
AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by your authorized dealer . V ertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.
5. Locate the vertical adjuster on each headlamp. Using a Phillips #2 screwdriver , turn the adjuster either clockwise (to adjust down) or counterclockwise (to adjust up). The horizontal edge of the brighter light should touch the horizontal reference line.
Y our vehicle may also have reading lamps within the rear dome lamp(s). Press the switches on either side of the dome lamp to turn on the lamps. BULB REPLACEMENT Headlamp Condensation The headlamps are vented to equalize pressure. When moist air enters the headlamp(s) through the vents, there is a possibility that condensation can occur .
Function Number of bulbs T rade number Fog lamp (if equipped) 2 H11 Map lamp 2 12V6W Dome/reading lamps 3 578 All replacement bulbs are clear in color except where noted. T o replace all instrument panel lights - see your authorized dealer . Replacing the interior bulbs Check the operation of all bulbs frequently .
2. Reach in behind the headlamp assembly to access the bulb sockets and connectors. 3. Remove the inboard rubber boot from the lamp assembly by pulling rearward. 4. Remove the bulb socket by turning it counterclockwise and pulling it straight out. Handle a halogen headlamp bulb carefully and keep out of children’ s reach.
Replacing rear brake/tail/turn/backup and side marker lamp bulbs The brake/tail/turn/backup and side marker lamp bulbs are located in the tail lamp assembly . Follow the same steps to replace either bulb. • (1) Backup lamp • (2) Brake/tail/turn lamp • (3) Side marker lamp 1.
Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the OFF position. 2. Remove the two screws from the license plate lamp assembly . 3. Remove bulb socket by turning counterclockwise. 4. Carefully pull the bulb out from the socket.
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid.
TILT STEERING WHEEL T o adjust the steering wheel: 1. Pull down and hold the steering wheel release control. 2. Move the steering wheel up or down until you find the desired location. 3. Pull the steering wheel release control up. This will lock the steering wheel in position.
INSTRUMENT PANEL STORAGE COMPARTMENT The storage compartment may be used to secure sunglasses or similar sized objects. Press the control to open the storage compartment. OVERHEAD CONSOLE The appearance of your vehicle’ s overhead console will vary according to your option package.
CENTER CONSOLE Y our vehicle may be equipped with a variety of console features. These include: 1. Cupholders 2. Utility compartment with coin holder , a clamshell tray , audio input jack, USB port and power point 3. Rear power point, vent and (if equipped) a cupholder 4.
T o have full capacity usage of your power point, the engine is required to be running to avoid unintentional discharge of the battery . T o prevent the battery from being discharged: • do not use t.
Press and pull the window switches to open and close windows. • Push down (to the first detent) and hold the switch to open. • Pull up (to the first detent) and hold the switch to close. Rear W indow Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise.
Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls (except for the driver’ s) press the right side of the control.
Automatic dimming interior rear view mirror (if equipped) Y our vehicle may be equipped with an interior rear view mirror that has an auto-dimming function. The electronic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the mirror .
T o adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror . 2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center position to lock mirrors in place.
• Press the bottom of the control to adjust the pedals towards you. The adjustment allows for approximately 2.8 inches (71 mm) of maximum travel. Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.
3. Press the SET + control and release it. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on.
Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. Y ou can also use the SET + control to operate the T ap-Up function.
Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal or press CNCL (Cancel). This will not erase your vehicle’ s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.
In AM, FM1, or FM2 mode: • Press SEEK to access the next/previous strong station. In Satellite radio mode (if equipped): • Press and release SEEK to access the next/previous strong station. • Press and hold SEEK to fast advance through preset channels or subscribed channels.
SYNC system hands free control feature (if equipped) Press briefly to use the voice command feature. Y ou will hear a tone and LISTENING will appear in the radio display . Press and hold to exit voice command. Press activate phone mode or answer a phone call.
T o close the moon roof: T o close, press the front portion of the control (to the first detent). T o activate the automatic, one-touch, express close feature, press the front portion of the control (to the second detent) and release quickly .
U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink 威 at: www .
• If the indicator light blinks rapidly for two seconds and then turns to a constant light continue with “Programming” Steps 4 through 6 to complete programming of a rolling code equipped device (most commonly a garage door opener).
• Proceed with Step 3 in the “Programming” section. Operating the HomeLink 姞 Wireless Control System T o operate, simply press and release the appropriate HomeLink 威 button. Activation will now occur for the trained product (garage door , gate operator , security system, entry door lock, or home or office lighting etc.
MESSAGE CENTER W ith the ignition in the ON position, the message center , located on your instrument cluster , displays important vehicle information through a constant monitor of vehicle systems. Y ou may select display features on the message center for a display of status.
The DTE function will display FUEL LEVEL LOW and a single tone when you have approximately 50 miles (80 km) to empty . If you RESET this warning message, this display and tone will return within 10 minutes. DTE is calculated using a running average fuel economy , which is based on your recent driving history of 500 miles (800 km).
2. Press and release RESET to pause the timer . 3. Press and hold RESET for 2 seconds in order to reset the timer . Compass display The compass heading is displayed in the lower left corner of the message center next to the odometer .
4. Press the SETUP control repeatedly until the message center says “RESET FOR ZONE SETTING”. 5. Press the RESET control to enter Zone Setting mode. 6. Press RESET repeatedly until the desired zone setting is displayed. The message center will automatically exit zone setting mode if enough time passes without pressing a button.
Setup menu Press this control for the following displays: • System Check • Oil Life • Language • Units (English/Metric) • Autolamp Delay (if equipped) • Autolock (if equipped) • Autounlo.
T o reset the oil monitoring system to 100% after each oil change [approximately 7,500 miles (12,000 km) or 6 months] perform the following: 1. Press the SETUP control to enter SYSTEM CHECK, then press SETUP control again to display “OIL LIFE = XXX% HOLD RESET = NEW”.
1. T o disable/enable the autolamp delay feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to select the new Autolamp delay values of 0, 10, 20, 30, 60, 90, 120 or 180 seconds.
In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for several seconds.
REAR LEFT DOOR AJAR. Displayed when the left rear door is not completely closed. REAR RIGHT DOOR AJAR. Displayed when the right rear door is not completely closed. FUEL LEVEL LOW . Displayed as an early reminder of a low fuel condition. CHECK CHARGING SYSTEM.
OIL CHANGE REQUIRED/CHANGE OIL SOON. Displayed when the engine oil life remaining is 5 percent or less. When oil life left is between 5% and 0%, the CHANGE OIL SOON message will be displayed. When oil life left reaches 0%, the OIL CHANGE REQUIRED message will be displayed.
CARGO AREA FEATURES Cargo net (if equipped) The cargo net secures lightweight objects in the cargo area. Attach the net to the anchors provided. Do not put more than 50 lb. (22 kg) in the net. This net is not designed to restrain objects during a collision.
KEYS Y our vehicle is equipped with two Integrated Keyhead T ransmitters (IKT s). The IKT functions as both a programmed ignition key that operates all the locks and starts the vehicle, and a remote keyless entry transmitter . Y our IKT s are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start.
When inserting the IKT into the ignition cylinder , place your thumb on the center thumb rest of the IKT and forefinger on the logo badge on the opposite side. T o gain more leverage when rotating the IKT in the ignition lock cylinder , you can readjust the location of your thumb to grasp the IKT on the outer edge next to the control.
Smart locks This feature helps to prevent you from locking yourself out of the vehicle if your key is still in the ignition. When you open one of the front doors and you lock the vehicle with the powe.
Power door lock switch autolock enable/disable procedure Before starting, ensure the ignition is in the 1 (LOCK) position and all vehicle doors are closed. Y ou must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again.
Autounlock feature The autounlock feature will unlock all the doors when: • the ignition is in the 3 (RUN) position, all the doors are closed, and the vehicle has been in motion at a speed greater t.
6. T o enable/disable the autounlock feature, press the lock control, then press the unlock control. The horn will chirp once if autounlock was deactivated or twice (one short and one long chirp) if autounlock was activated. 7. T urn the ignition to the 1 (LOCK) position.
INTERIOR LUGGAGE COMPARTMENT RELEASE Y our vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the operation and location of the release handle.
REMOTE ENTRY SYSTEM The Integrated Keyhead T ransmitter (IKT) complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This.
Unlocking the doors/two stage unlock 1. Press and release to unlock the driver’ s door . Note: The interior lamps will illuminate. 2. Press and release again within three seconds to unlock all the doors.
Opening the trunk Press twice within 3 seconds to open the trunk. • Ensure that the trunk is closed and latched before driving your vehicle. Failure to properly latch the trunk may cause objects to fall out or block the driver’ s rear view .
Replacing the battery The Integrated Keyhead T ransmitter uses one coin type three-volt lithium battery CR2032 or equivalent. T o replace the battery: 1. T wist a thin coin in the slot of the IKT near the key ring in order to remove the battery cover .
Illuminated entry The interior lamps and puddle lamps (if equipped) illuminate when the Integrated Keyhead T ransmitter or the keyless entry system keypad is used to unlock the door(s).
1. Place the key in the ignition and turn the ignition to the 3 (RUN) position. 2. Press the power door unlock control on the door panel three times. 3. T urn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times.
KEYLESS ENTRY SYSTEM Y ou can use the keyless entry keypad to: • lock or unlock the doors without using a key . • open the trunk. • recall memory seat/power mirrors positions (if equipped).
T ips: • Do not set a code that uses five of the same number . • Do not use five numbers in sequential order . • The factory set code will work even if you have set your own personal code. Erasing personal code 1. Enter the factory set 5–digit code.
started unless a coded Integrated Keyhead T ransmitter (IKT) programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Y our vehicle comes with two coded Integrated Keyhead T ransmitters; additional coded IKT s may be purchased from your authorized dealer .
The theft indicator will flash every two seconds to act as a theft deterrent when the vehicle is armed. Automatic disarming The vehicle is disarmed immediately after the ignition is turned to the 3 (RUN) position. The theft indicator will illuminate for three seconds and then go out.
• If two previously programmed coded keys are not available, you must take your vehicle to your authorized dealer to have the spare key(s) programmed. Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition.
PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help protect your vehicle from unauthorized entry . If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL Integrated Keyhead T ransmitters are brought to the authorized dealer to aid in troubleshooting.
• Press the 7 • 8a n d9 • 0 controls on the keyless entry pad at the same time to lock the doors (driver’ s door must be closed). There is a 20 second countdown when any of the above actions occur before the vehicle becomes armed.
SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Push release button to lower head restraint. Using the manual lumbar support (if equipped) The lumbar support control is located on the outboard side of the seatback.
Cover sharp edges on the load to help prevent injury to occupants. Secure the load to help prevent shifting during sudden stops. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.
Pull lever up to adjust seatback. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched.
T o reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in map pocket (if equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped).
Press the control (if equipped) to recline the seatback forward or rearward. Heated seats (if equipped) Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater .
Memory seats/power mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, power mirrors, and adjustable pedals to two programmable positions.
The head restraints can be moved up by pulling up on the head restraint. Push release button to lower head restraint. Split-folding rear seat One or both rear seatbacks can be folded down to provide additional cargo space.
Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.
• Driver’ s seat position sensor . • Front passenger sensing system • “Passenger airbag off” or “pass airbag off” indicator lamp • Front crash severity sensor . • Restraints Control Module (RCM) with impact and safing sensors. • Restraint system warning light and back-up tone.
levels of crash severity and modify the deployment strategy of the dual-stage airbags and safety belt pretensioners. Driver ’s seat position sensor The driver’ s seat position sensor allows your Personal Safety System™ to tailor the deployment level of the driver dual-stage airbag based on seat position.
allows your Personal Safety System™ to tailor the airbag deployment and safety belt pretensioner activation depending upon safety belt usage. Refer to Safety belt section in this chapter .
Safety belt precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. T o reduce the risk of injury , make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving.
Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. T o unfasten, push the release button and remove the tongue from the buckle.
All safety restraints in the vehicle are combination lap and shoulder belts. All of the passenger combination lap and shoulder belts have two types of locking modes described below: V ehicle sensitive.
• Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.
hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced. However , if the collision was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly , they do not need to be replaced.
The Belt-Minder 威 feature uses information from the front passenger sensing system to determine if a front seat passenger is present and therefore potentially in need of a warning.
The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers.
Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. T o do so may adversely affect the performance of the vehicle’ s air bag system.
2. W ait until the safety belt warning light turns off (Approximately 1 minute). • Step 3 must be completed within 50 seconds after the safety belt warning light turns off. 3. For the seating position being disabled, at a moderate speed, buckle then unbuckle the safety belt nine times, ending in the unbuckled state.
outboard passenger from certain upper body injuries. The term “supplemental restraint” means the airbags are intended as a supplement to the safety belts.
• Recline the seat slightly (one or two degrees) from the upright position. Do not put anything on or over the airbag module. Placing objects on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury .
How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation.
Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
The front passenger sensing system will disable (will not inflate) the front passenger’ s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects in the front seat.
The front passenger sensing system is designed to enable (may inflate) the front passenger’ s frontal airbag anytime the system senses that a person of adult size is sitting properly in the front passenger seat.
Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the front passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor .
T o reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped).
Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The supplemental restraint system uses a warning indicator light in the instrument cluster or a back-up tone to indicate the condition of the system.
Do not attempt to service, repair , or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. See your authorized dealer . All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided.
The airbag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system.
Do not lean your head on the door . The Safety Canopy™ could injure you as it deploys from the headliner . Do not attempt to service, repair , or modify the Safety Canopy™ system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy™.
• A headliner designed to flex open above the side doors to allow Safety Canopy™ deployment. • The same readiness airbag light, electronic control and diagnostic unit as used for the front airbags. • T wo crash sensors mounted on the B pillar (one on each side of the vehicle).
If the Safety Canopy™ system has deployed, the Safety Canopy™ will not function again unless replaced. The Safety Canopy™ system (including the A, B, and C pillar trim) must be inspected and serviced by an authorized dealer . If the Safety Canopy™ is not replaced, the unrepaired area will increase the risk of injury in a collision.
Important child restraint precautions Y ou are required by law to use safety restraints for children in the U.S. and Canada. If small children (generally children who are four years old or younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, you must put them in safety seats made especially for children.
T o improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster . Booster seats position a child so that safety belts fit better . They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably .
T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt.
Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child.
and anchors, refer to Attaching safety seats with tether straps in this chapter . For more information of LA TCH anchors refer to Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments in this chapter . Carefully follow all of the manufacturer’ s instructions included with the safety seat you put in your vehicle.
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. T ether straps are available as an accessory for many older safety seats.
4. Open the tether anchor cover . 5. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 6. Install the child safety seat tightly using the LA TCH anchors or safety belts.
Y our vehicle has LA TCH anchors for child seat installation at the seating positions marked with the child seat symbol. All the LA TCH lower anchors are equally spaced, so that a single LA TCH child seat can be installed at any rear seating position.
lifting the front of the child seat. Keeping the child seat just touching the vehicle seat gives the best protection in a severe crash. Each time you use the safety seat, check that the seat is properly attached to the lower anchors and tether anchor .
INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING T ire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.
Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability . • kPa: Kilopascal, a metric unit of air pressure.
Under -inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury . Under -inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire.
when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure. 3. Add enough air to reach the recommended air pressure.
Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydroplaning. Built-in treadwear indicators, or “wear bars”, which look like narrow strips of smooth rubber across the tread will appear on the tire when the tread is worn down to 1/16th of an inch (2 mm).
U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.
When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again.
• Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds.
• Front Wheel Drive (FWD) vehicles (front tires at top of diagram) • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires.
Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter . 6. 95: Indicates the tire’ s load index. It is an index that relates to how much weight a tire can carry .
8. U.S. DOT T ire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built.
Label or T ire Label which is located on the B-Pillar or the edge of the driver’ s door . The cold inflation pressure should never be set lower than the recommended pressure on the vehicle label. The tire suppliers may have additional markings, notes or warnings such as standard load, radial tubeless, etc.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The T ire Pressure Monitoring System is NOT a substitute for manually checking tire pressure.
When your temporary spare tire is installed When one of your road tires needs to be replaced with the temporary spare, the TPMS system will continue to identify an issue to remind you that the damaged road wheel/tire needs to be repaired and put back on your vehicle.
Low T ire Pressure W arning Light Possible cause Customer Action Required Solid W arning Light T ire(s) under -inflated 1. Check your tire pressure to ensure tires are properly inflated; refer to Inflating your tires in this chapter .
Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use.
How temperature affects your tire pressure The T ire Pressure Monitoring System (TPMS) monitors tire pressure in each pneumatic tire. While driving in a normal manner , a typical passenger tire inflation pressure may increase approximately 2 to 4 psi (14 to 28 kPa) from a cold start situation.
• Do not use tire chains, cables, or optional traction devices with optional P225/55R18 tires. • Install cable chains securely , verifying that the cables do not touch any wiring, brake lines or fuel lines. • Drive cautiously . If you hear the cables rub or bang against your vehicle, stop and re-tighten the cables.
Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s door (vehicles exported outside the US and Canada may not have a T ire Label).
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage.
2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity .
1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now you have the load capacity to transport the cement and your friend home. In metric units, the calculation would be: 635 kg - (2 x 99 kg) - (9 x 45 kg) = 635 - 198 - 405 = 32 kg.
If you use a rental trailer , follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper . T railer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’ s specifications.
T railer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached.
Note: If you tow your vehicle with all four wheels on the ground, follow these instructions: • T ow only in the forward direction • Release the parking brake • Place the transmission shift lever in Neutral (N) • T urn the key in the ignition to the ACC position (refer to Starting in the Driving chapter).
STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. This position also shuts the engine and all electrical accessories off. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running.
Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic.
• Make sure the gearshift lever is in P (Park). 3. T urn the key to 3 (RUN) without turning the key to 4 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights.
This vehicle has a computer assisted cranking system which assists in starting the engine. If the ignition key is turned to 4 (ST ART) and then released when the engine begins cranking, the engine may continue cranking for up to 10 seconds or until the vehicle starts.
with Outdoor Appliances. ⬙ Never use an indoor extension cord outdoors; it could result in an electric shock or fire hazard. • Use a 16 gauge outdoor extension cord, minimum. • Use as short an extension cord as possible. • Do not use multiple extension cords.
Make sure system is unplugged and properly stowed before driving the vehicle. While not in use, make sure the protective cover seals the prongs of the engine block heater cord plug.
Even when the ABS is disabled, normal braking is still effective. If your BRAKE warning lamp illuminates with the parking brake released, have your brake system serviced immediately . Parking brake Apply the parking brake whenever the vehicle is parked.
Push the parking brake pedal downward again to release the parking brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy . Note: If the vehicle is driven with the parking brake applied, a chime will sound.
• Entering a paved road from a gravel road, or vice versa • Hitting a curb while turning • Cornering at excessive speeds while towing a heavily loaded trailer (refer to T railer towing in the T ires, Wheels and Loading chapter) The AdvanceT rac 威 system automatically turns on when the engine is started.
All these conditions are normal during AdvanceT rac 威 operation. If the AdvaceT rac system is activated for an extended period of time, the brake portion of the system will shut down to allow the brakes to cool down. A limited AdvanceT rac 威 function using only engine power reduction will still help control the wheels from over -spinning.
During T raction Control™ operation the engine will not “rev-up” when you push further on the accelerator . This is normal system behavior . If you should become stuck in deep snow or on a very slippery road surface, try switching the T raction Control™ system off.
If the steering wanders or pulls, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering al.
Do not drive your vehicle until you verify that the brakelamps are working. Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle.
Understanding the gearshift positions of the 6–speed automatic transaxle P (Park) This position locks the transaxle and prevents the front wheels from turning.
D (Drive) with Overdrive The normal driving position for the best fuel economy . T ransaxle operates in gears one through six. D (Drive) with Overdrive Cancel and Grade Assist Pressing the transmission control switch on the side of the gearshift lever activates two features at the same time: Overdrive Cancel and Grade Assist.
T o return to O/D (overdrive mode), press the transmission control switch again. • The O/D OFF lamp in the instrument cluster will not be illuminated. • The transmission will operate in gears one through six. O/D (overdrive mode) is automatically returned each time the key is turned off.
The RSS detects obstacles up to six feet (two meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases.
ALL WHEEL DRIVE (A WD) SYSTEM (IF EQUIPPED) Y our vehicle may be equipped with a full-time All Wheel Drive (A WD) system. W ith the A WD option, power will be delivered to the front wheels and distributed to the rear wheels as needed. The A WD system is active all the time and requires no input from the operator .
• It may be safer to stay on the apron or shoulder of the road and slow down gradually before returning to the pavement. Y ou may lose control if you do not slow down or if you turn the steering wheel too sharply or abruptly .
not more. Additionally , smooth variations of the accelerator and/or brake pedal pressure should be utilized if changes in vehicle speed are called for . A void abrupt steering, acceleration or braking which could result in an increased risk of loss of vehicle control, vehicle rollover and/or personal injury .
Be cautious of sudden changes in vehicle speed or direction when you are driving in mud. Even A WD vehicles can lose traction in slick mud. As when you are driving over sand, apply the accelerator slowly and avoid spinning your wheels. If the vehicle does slide, steer in the direction of the slide until you regain control of the vehicle.
Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear . When descending a steep hill, avoid sudden hard braking as you could lose control.
Maintenance and Modifications The suspension and steering systems on your vehicle have been designed and tested to provide predictable performance whether loaded or empty and durable load carrying capability .
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Canadian customers refer to your Customer Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursemen.
HAZARD FLASHER CONTROL The hazard flasher is located on the instrument panel by the radio. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash.
FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating.
Passenger compartment fuse panel The fuse panel is located under the instrument panel to the left of the steering wheel. The fuses are coded as follows.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 8 10A Low beam headlamps (right) 9 15A Interior lights, Cargo lamps 10 15A Backlighting, Puddle lamps 11 10A All wheel drive 12 7.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 36 5A P A TS module 37 10A Climate control 38 20A Subwoofer (Audiophile radio) 39 20A Radio 40 20A Spare 41 15A Mic mir.
The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 80A* SPDJB power 2 80A* SPDJB power 3 30A* Front wipers 4 — Not used 5 20A Spare.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 16 20A** Power point (console) 17 10A** Alternator 18 — Not used 19 — Not used 20 40A* Rear defroster 21 30A* Power seat moto.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 45 10A** Speed control deactivate switch, Mass air flow sensor , Inline module VPWR2 46 10A** A/C clutch relay , VPWR3 47 15A** P.
Refer to T ire Pressure Monitoring System (TPMS) in the T ires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, it will no longer function.
Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capability 3.
Stopping and securing the vehicle 1. Park on a level surface, set the parking brake and activate hazard flashers. 2. Place gearshift lever in P (Park) and turn engine off. Removing the spare tire and jack 1. Lift the trunk cargo cover , and remove the wing nut that secures the spare tire by turning it counterclockwise.
T o help prevent the vehicle from moving when you change a tire, be sure to place the transaxle in P (Park), set the parking brake and block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
3. Put the jack in the jack notch next to the tire you are changing. T urn the jack handle clockwise until the wheel is completely off the ground. 4. Remove the lug nuts with the lug wrench. 5. Replace the flat tire with the spare tire, making sure the valve stem is facing outward.
Stowing the tire and jack 1. Fully collapse the jack, fold the lug wrench socket into the handle and place the jack and wrench into the felt bag as shown. T ake care to position the jack as shown to ensure that the locating holes in the jack base can be placed on the locating tabs of the jack mounting bracket in the spare tire tub.
2. Place the tire, with the wheel facing downward, into the spare tire well and secure the wheel with the large wing nut. If you are stowing the temporary spare tire, place the tire over the jack and secure it with the large wing nut.
Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger .
4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. T urn the heater fan on in both vehicles to protect from any electrical surges. T urn all other accessories off.
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system.
3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment.
If the vehicle is towed by other means or incorrectly , vehicle damage may occur . In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer , or fl.
GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.
In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states.
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide.
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the au.
If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www .
ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.
T o contact NHTSA, you may call the V ehicle Safety Hotline toll-free at 1–888–327–4236 (TTY : 1–800–424–9153); go to http://www.safercar .gov; or write to: Administrator 1200 New Jersey A venue, Southeast W ashington, D.C. 20590 Y ou can also obtain other information about motor vehicle safety from http://www.
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
W AXING • W ash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid W ax (ZC-53-A), which is available from your authorized dealer , or an equivalent quality product.
ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage.
• For routine cleaning, use Motorcraft Detail W ash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and T ar Remover (ZC-42). • For plastic headlamp lenses, use Motorcraft Ultra Clear Spray Glass Cleaner (ZC-23).
INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with a clean and damp white cotton cloth, then with a clean and dry white cotton cloth; you may also use Motorcraft Dash & Vinyl Cleaner (ZC-38-A) on the instrument panel and interior trim areas.
• If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover (ZC-14). In Canada, use Motorcraft Multi-Purpose Cleaner (CXC-101). • If a ring forms on the fabric after spot cleaning, clean the entire area immediately (but do not oversaturate) or the ring will set.
FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Y our Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service.
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel near the steering column. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.5L V6 ENGINE 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Automatic transmission fluid dipstick 8.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. T urn the blade at a right angle to the arm. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it. 3. Attach the new blade to the arm and snap it into place.
5. Locate and carefully remove the engine oil level dipstick. 6. W ipe the dipstick clean. Insert the dipstick fully , then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range.
• Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer . 7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1.
to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.
It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time.
4. Allow the engine to idle for at least one minute. 5. T urn the A/C on and allow the engine to idle for at least one minute. 6. Release the parking brake. W ith your foot on the brake pedal and with the A/C on, put the vehicle in D (Drive) and allow the engine to idle for at least one minute.
60%, the engine parts could become damaged or not work properly . A 50–50 mixture of coolant and water provides the following: • Freeze protection down to -34°F (-36°C). • Boiling protection up to 265°F (129°C). • Protection against rust and other forms of corrosion.
Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container .
remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap.
Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner .
• Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive. V ehicles driven year -round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection.
Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed.
Refueling Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off yo.
At the next opportunity , safely pull off of the road, remove the fuel filler cap, align the cap properly and reinstall it. The check fuel cap light or “check fuel cap” message may not reset immediately; it may take several driving cycles for the check fuel cap light or “check fuel cap” message to turn off.
Y our vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based additives. Studies indicate that these additives can cause your vehicle’ s emission control system to deteriorate more rapidly .
Cleaner air Ford endorses the use of reformulated “cleaner -burning” gasolines to improve air quality , per the recommendations in the Choosing the Right Fuel section. Running out of fuel A void running out of fuel because this situation may have an adverse effect on powertrain components.
The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty , you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank.
Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy . Habits • Smooth, moderate operation can yield up to 10% savings in fuel.
• Carrying unnecessary weight may reduce fuel economy (approximately 1 mpg [0.4 km/L] is lost for every 400 lb [180 kg] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy .
If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability .
2. Poor fuel quality or water in the fuel—the engine may misfire or run poorly . 3. The fuel cap may not have been securely tightened. See Fuel filler cap in this chapter .
The OBD-II system is designed to check the emission control system during normal driving. A complete check may take several days. If the vehicle is not ready for I/M testing, the following driving cyc.
BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid.
7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated areas for normal operating temperature. Low fluid level Do not drive the vehicle if the fluid level is in the add range or does not show at all on the dipstick.
If an overfill occurs, excess fluid should be removed by an authorized dealer . An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments or cleaning agents.
6. Replace the air filter housing cover and secure the clamps. Be sure that the air cleaner cover tabs are engaged into the slots of the air cleaner housing.
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Items Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification Brake fluid Between MAX and MIN on reservoir Motorcraft High Perform.
Items Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification Engine oil 5.5 quarts (5.2L) Motorcraft SAE 5W -20 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W -20 Super Premium Motor Oil (Canada) 3 XO-5W20-QSP (US) CXO-5W20- LSP12 (Canada) / WSS-M2C930-A and API Certification Mark Engine coolant 11.
Items Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification Fuel tank 20.5 gallons (77.6L) A WD, PZEV A WD and PZEV FWD —— 20.0 gallons (75.7L) (FWD) 1 Approximate dry fill capacity . Actual amount may vary during fluid changes.
ENGINE DATA Engine 3.5L-DOHC V6 engine Displacement 3.5L Required fuel 87 octane Firing order 1–4–2–5–3–6 Spark plug gap (0.052–0.056 inch) 1.32–1.42 mm Ignition system Coil on plug Compression ratio 10.3:1 Engine drivebelt routing • 3.
IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint System 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6.
GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer .
Peace of mind Remote start V ehicle security systems Wheel locks For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When .
A Accessory delay .......................... 97 AdvanceT rac .............................. 227 Air cleaner filter ............... 310–311 Air conditioning ....................76, 78 Airbag supplemental restraint system ................162–163, 171, 173 and child safety seats .
plastic parts ............................ 277 washing .................................... 275 waxing ..................................... 276 wheels ...................................... 276 wiper blades ............................ 278 Climate control (see Air conditioning or Heating) .
Exhaust fumes .......................... 223 F Family entertainment system .... 44 Fluid capacities ......................... 312 Foglamps ..................................... 82 Four -Wheel Drive vehicles driving off road ....................... 237 Fuel .
autolock ................................... 123 keypad ..................................... 134 locking and unlocking doors .. 135 programming entry code ....... 134 Keys ...................................121, 137 positions of the ignition ........
Rear seat entertainment system .......................................... 44 Relays ........................................ 246 Remote entry system ....... 128–129 illuminated entry ............ 132–133 locking/unlocking doors ......... 129 opening the trunk .
sidewall information ............... 199 snow tires and chains ............ 209 spare tire ................................. 253 terminology ............................. 190 tire grades ............................... 190 treadwear ..................
326.
327.
328.
An important point after buying a device Ford 2008 Ford Taurus (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ford 2008 Ford Taurus yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ford 2008 Ford Taurus - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ford 2008 Ford Taurus you will learn all the available features of the product, as well as information on its operation. The information that you get Ford 2008 Ford Taurus will certainly help you make a decision on the purchase.
If you already are a holder of Ford 2008 Ford Taurus, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ford 2008 Ford Taurus.
However, one of the most important roles played by the user manual is to help in solving problems with Ford 2008 Ford Taurus. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ford 2008 Ford Taurus along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
