Instruction/ maintenance manual of the product 2006 Crown Victoria Ford
Go to page of 272
Introduction 4 Instrument Cluster 10 W arning and control lights 10 Gauges 14 Entertainment Systems 17 AM/FM stereo 17 AM/FM stereo cassette 19 AM/FM stereo with CD 21 AM/FM stereo cassette with CD 25.
Seating and Safety Restraints 99 Seating 99 Safety restraints 104 Airbags 119 Child restraints 131 Tires, Wheels and Loading 143 T ire Information 143 V ehicle loading 157 T railer towing 163 Recreati.
Maintenance and Specifications 221 Engine compartment 222 Engine oil 224 Battery 227 Engine Coolant 229 Fuel information 235 Air filter(s) 251 Part numbers 251 Refill capacities 252 Lubricant specifications 254 Accessories 260 Index 262 All rights reserved.
CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’ s New V ehicle Limited W arranty , refer to the Warranty Guide that is provided to you along with your Owner’ s Guide.
Special instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter . Failure to follow the specific warnings and instructions could result in personal injury .
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat Installation.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant .
W ARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions.
Check engine: The Check engine indicator light illuminates when the ignition is first turned to the ON position to check the bulb. Solid illumination after the engine is started indicates the On Board Diagnostics System (OBD-II) has detected a malfunction.
Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur . It will take you longer to stop the vehicle.
Never remove the coolant reservoir cap while the engine is running or hot. T raction control 娂 AdvanceT rac 威 active (if equipped): Illuminates when the T raction control 娂 system is active. It will be lit for a minimum of four seconds or for the duration of the T raction Control 娂 event, refer to the Driving chapter for more information.
T urn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster , check for a burned out bulb.
Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.
• W ith Message Center Press and release the message center INFO button until “TRIP” appears in the display (this represents the trip mode). Press the control again to select T rip A and T rip B features. Press and hold the RESET button for two seconds to reset.
AUDIO SYSTEMS AM/FM stereo (if equipped) 1. Seek: Press / to find the next strong station down/up the frequency band. 2. T une: Press / to manually change radio frequency down/up.
4. Memory preset buttons: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 5. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 6. T one: Press TONE until the desired level — Bass, T reble, Fade appears on the display .
AM/FM stereo cassette (if equipped) 1. Balance: Press to shift sound to the left/right speakers. 2. Fade: Press to shift sound to the rear/front speakers. 3. CLK: T o set the hour , press and hold CLK. Then press SEEK to decrease or increase the hours.
4. T ape AMS: In tape mode, press and hold to activate Automatic Music Search (allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection). Then, press REW (for the beginning of the current selection) or FF (to advance to the next selection).
13. AM/FM: Press to choose a frequency band in radio mode. 14. Bass: Press / to decrease/increase the bass output. 15. T reble: Press / to decrease/increase the treble output. 16. EJ (Eject): Press to eject a tape. 17. Cassette door: Insert a cassette into the cassette door .
1. CD slot: Insert a CD, label side up. W ith the ignition on, the radio will begin play when a CD is inserted. If the ignition is off, press CD prior to inserting a disc. Do not force a disc into the system as damage could result. 2. SEEK: Press to access the next ( ) or previous ( ) radio station or CD track.
8. SEL: Use with Bass, T reble, Balance, Fade and other menu functions. 9. MENU: Press MENU to access the following functions: Compression: Brings soft and loud CD passages together for a more consistent listening level when in CD mode. Press MENU until compression status is displayed.
11. On/Off/V olume: Push to turn on/off; turn to adjust the volume levels. Note: W ith the ignition turned off, you may press the volume control to momentarily view the clock. 12. CD: Press to enter CD mode if a CD is already present in the system. In radio mode, the CD icon will appear in the display if a CD is loaded into the system.
Premium/Audiophile Satellite Compatible AM/FM Stereo Single CD/Cassette system (if equipped) 1. CD slot: Insert a CD, label side up. W ith the ignition on, the radio will begin to play a CD once inserted. W ith the ignition off, the CD control must be pressed before inserting the disc.
TREB (T reble): Press TREB; then press SEL-TEXT to decrease/increase the level of treble output. 4. BAL (Balance): Press BAL; then press SEL-TEXT to shift sound to the left/right speakers. F ADE: Press F ADE; then press SEL-TEXT to shift sound to the rear/front speakers.
W ith RDS ON, press MENU until the program type menu is displayed. One of the various program types will appear . Press SEL-TEXT to scroll through music types. Press SEEK or SCAN to search for a station playing the requested music category . Show TYPE: Selects between displaying the station’ s call letters or music format when RDS is enabled.
The Dolby 威 noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Dolby 威 and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Setting the clock: Press MENU repeatedly until SELECT HOUR or SELECT MINS is displayed.
13. SCAN: Press SCAN to hear a brief sampling of radio stations, selections or CD tracks. Press again to stop. 14. SHUF (Shuffle): Press to play the tracks on the current CD in random order . Press again to stop. 15. Memory presets: T o set a station: Select frequency band, tune to a station, press and hold a preset button until sound returns.
Audiophile AM/FM Satellite Compatible Stereo In-dash Six CD sound system (if equipped) 1. CD slot: T o insert a CD, press LOAD. When the system is ready , insert a CD, label side up. 2. SEEK: Press to access the next/previous radio station or CD track.
4. MUTE: Press to mute the playing media. Press again to return to the playing media or turn the volume control to adjust the volume. 5. Eject: Press to eject CD(s) when the ignition is on or off. Numbers will illuminate in the display indicating which CD slots are loaded with CDs.
9. MENU: Press MENU repeatedly to access RDS on/off. Use SEL-TEXT to toggle RDS on/off. Press MENU again to access Program type mode or Show T ype mode.
Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3. Level 0 turns the feature off and level 7 is the maximum setting. Press MENU to access and use SEL-TEXT to adjust the volume setting.
15. SA T : Y our system may be equipped with Satellite Ready capability . The kit to enable the Satellite reception is available through your authorized dealer . Detailed satellite instructions are included with the dealer installed kit. Dealer installed satellite kit available only in the continental United States.
Don’t: • Expose tapes to direct sunlight, extreme humidity , heat or cold. • Leave tapes in the cassette player for a long time when not being played. CD/CD player care: Do: • Handle discs by their edges only . Never touch the playing surface.
MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle.
T o aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to HI.
3. Fan speed: T urn to manually increase or decrease fan speed. 4. Defrost: Distributes outside air through the windshield defroster vents and the side window demisters. 5. Floor/defrost: Distributes outside air through the windshield defroster vents, floor vents and the side window demisters.
• Remove any snow , ice or leaves from the air intake area at the base of the windshield. T o aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to HI.
HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) T urns the lowbeam headlamps on with a reduced output.
P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate the thumbwheel from left to right to brighten the instrument panel. • Rotate the thumbwheel from right to left to dim the instrument panel.
INTERIOR LAMPS Map/Courtesy lamps The courtesy lamps light when: • any door is opened. • the instrument panel dimmer switch is rotated past the detent. • the UNLOCK control of the remote entry controls is pressed and the ignition is OFF . The reading lamps can be turned on by pressing the rocker controls next to each lamp.
Rear courtesy/reading lamps Rotate the lens to illuminate the lamp. W ith the lens in the flat position, the courtesy lamp lights when: • Any door is opened. • The panel dimmer thumbwheel is rotated fully to the right past detent. BULB REPLACEMENT Headlamp Condensation The headlamps are vented to equalize pressure.
Function T rade Number License plate lamp 168 High-mount brakelamp 912 Luggage compartment lamp 212-2 Rear reading lamp 578 Map lamp 906 Dual floorwell lamp 906 Glove compartment 168 Visor vanity lamp - Slide on Rail system (SOR) 37 All replacement bulbs are clear in color except where noted.
3. Disconnect the electrical connector from the bulb by pulling rearward. 4. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb.
5. T urn the headlamps on and make sure they work properly . If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again. Replacing front parking lamp/turn signal bulbs The park/turn lamp bulbs can be replaced without removing the headlamp assembly .
1. Make sure headlamp switch is in OFF position, then open the trunk and remove plastic retainer to expose the lamp assembly hardware. 2. Carefully pull the carpet away to expose the plastic retainer . 3. Remove three nut and washer assemblies and the lamp assembly from the vehicle.
Replacing license plate lamp bulbs 1. Make sure headlamp switch is in OFF position, then remove two screws, grommets and the license plate lamp assembly from the trunk lid.
Replacing high-mount brakelamp bulbs 1. Make sure headlamp switch is in OFF position, then remove two screws from the lamp assembly . 2. Carefully lift the lamp assembly up for access to the bulbs. 3. Carefully pull the bulb socket out of the lamp assembly .
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid.
ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamp. Slide on rod feature (if equipped) Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: T o stow the visor back into the headliner , visor must be retracted before moving it back towards the windshield.
The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in or on the vehicle may also affect compass accuracy . Adjustments may need to be made to the zone and calibration of the compass.
OVERHEAD CONSOLE WITH MOON ROOF (IF EQUIPPED) The appearance of your vehicle’ s overhead console will vary according to your option package. Some of the features in the overhead console include Compass, Homelink, and Moon Roof controls.
2. Hold down the MODE button for 5 seconds to enter zone mode. The display will read PRESS RESET TO SET ZONE XX where XX is the current zone. 3. Release the MODE button.
2. Hold down the MODE button for 10 seconds to enter the calibration mode. The display will read PRESS RESET TO DECAL. 3. Release the MODE button. 4. Press the RESET button to de-calibrate the compass. The display will read CIRCLE SLOWL Y TO CALIBRA TE for a few seconds and then display a direction with CAL displayed on the right side.
door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink 威 at: www .homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.
2. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink 威 button you wish to program (located on your overhead console) while keeping the display in view . 3. Simultaneously press and hold both the HomeLink 威 and hand-held transmitter button.
5. Press and hold the just-trained HomeLink 威 button and observe the HomeLink 威 house icon on the display . If the indicator light(s) underneath the house icon are constant, programming is complete and your device should activate when the HomeLink 威 button is pressed and released.
• Continue to press and hold the HomeLink 威 button (note step 3 in the “Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink 威 .
• After about 20 seconds, the message CHANNELS CLEARED will appear on the display . Do not hold for longer that 30 seconds. HomeLink 威 is now in the train (or learning) mode and can be programmed at any time beginning with step 2 in the “Programming” section.
AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug.
Press and hold the bottom part of the rocker switch to open the window . Press and hold the top part of the rocker switch to close the window . One touch down Allows the driver’ s window to open fully without holding the control down. Press completely down on the bottom part of the rocker switch and release quickly .
Do not block the sensor on the backside of the inside rear view mirror since this may impair proper mirror performance. EXTERIOR MIRRORS Power side view mirrors T o adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror .
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal.
3. Press the SET + control and release it. 4. T ake your foot off the accelerator pedal. 5. The indicator light (if equipped) on the instrument cluster will turn on.
Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. Y ou can also use the SET + control to operate the T ap-Up function.
Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’ s previously set speed. • Press the speed control OFF control. Note: When you turn the speed control or the ignition off, your speed control set speed memory is erased.
Climate control features • Press TEMP + or - to adjust temperature. MOON ROOF (IF EQUIPPED) T o vent the moon roof: • Press and hold the control forward to raise the moon roof to the vent position (when the glass panel is closed).
HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 W ireless Control System, located on the overhead console, provides a convenient way to replace up to three hand-held transmitters with a single built-in device.
1. Press and hold the two outside buttons releasing only when the indicator light begins to flash after 20 seconds. Do not repeat Step 1 to program additional hand-held transmitters to the remaining two HomeLink 威 buttons. This will erase previously programmed hand-held transmitter signals into HomeLink 威 .
7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer .) Note: There are 30 seconds in which to initiate Step 8. 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink 威 button.
Operating the HomeLink 姞 Wireless Control System T o operate, simply press and release the appropriate HomeLink 威 button. Activation will now occur for the trained product (garage door , gate operator , security system, entry door lock, or home or office lighting etc.
MESSAGE CENTER (IF EQUIPPED) W ith the ignition in the ON position, the message center , located on your instrument cluster , displays important vehicle information through a constant monitor of vehicle systems. Y ou may select display features on the message center for a display of status.
Reset Press this control to reset functions shown in the INFO menu and SETUP menu. Info menu This control displays the following control displays: • T rip odometer/Odometer • Distance to Empty • A verage Fuel Economy • Instantaneous Fuel Economy Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter .
Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing gallons.
Setup menu Press this control for the following displays: • System Check • Display (odometer/speedometer) • Font Size (normal/large) • Units (English/Metric) • Language • Oil Minder Start V alue System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored.
Display T ype 1. Select this function from the SETUP menu. 2. Press the SELECT control to change the display . Font Size 1. Select this function from the SETUP menu. 2. Press the SELECT control to change font size. Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed.
Oil Minder Start V alue 1. Select this function from the SETUP control for the current display mode. 2. Press the SELECT control to change oil value. System warnings System warnings alert you to possible problems or malfunctions in your vehicle’ s operating systems.
W arning display Status Door Ajar W arning cannot be reset Coolant over temperature W arning returns after 10 minutes Powertrain malfunction Check fuel cap Check air suspension Low fuel Overdrive ON/OFF W arning returns after the ignition key is turned from OFF to ON.
Center . Once this message disappears (after approximately 2 seconds), press RESET to clear the warning. TRUNK AJAR. Displayed when the trunk is not completely closed. OVERDRIVE ON/OFF . Displayed when the overdrive is enabled or disabled. CHECK COMP ASS MODULE.
INTERIOR TRUNK CONTROL The remote trunk release control is located on the driver’ s door trim panel and can be operated at any time. Y ou can render the switch inoperable by locking the button with your master key .
KEYS The vehicle is equipped with a master (black) key and valet (gray) key lock system. • The master key will access the vehicle’ s doors, trunk, glove box, ignition and remote trunk release. • The valet key will access doors and ignition only .
Smart locks (if equipped) W ith the key in any ignition position, and either the driver’ s or passenger’ s door open, the doors cannot be locked using the power door lock switches. The vehicle may still be locked with the key in the ignition, and performing one of the following actions: • Pressing the manual lock button on the door .
T o open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “T” shaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light.
REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Press again within three seconds to receive confirmation that the vehicle was successfully locked. Note: If all vehicle doors are closed upon the second press of the , the horn will chirp once and the parklamps/taillamps will flash once to confirm the successful locking.
2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery . Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery .
Place the key in the ignition and cycle from 1 (OFF/LOCK) to 3 (ON) eight times in rapid succession within 10 seconds. After doors lock/unlock, press any control on all transmitters (up to four). After pressing the control on each remote transmitter , the door will lock and unlock.
Autolock (if equipped) This feature automatically locks all vehicle doors when: • all doors are closed, • the engine is running, • you shift into any gear , putting the vehicle in motion, and • the vehicle’ s speed is greater than 3 mph (5 km/h).
5. T urn the ignition back to the 3 (ON) position. 6. The door locks will lock/unlock to confirm programming mode is entered/active. 7. W ith the ignition still in the 3 (ON) position, for the autolock feature, press the unlock control once then press the lock control once.
2. W ithin five seconds press 1 • 2 on the keypad to enter the programming mode. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other . 4. Press 1 • 2 to store the first personal code. 5. The doors will lock then unlock to confirm programming of the new code.
2. Press and release 1 • 2 within 5 seconds of step 1. 3. Press and hold 1 • 2 for two seconds. All of the vehicle doors will lock and then unlock to confirm erasure.
Radio type approval numbers for Immobiliser System P A TS XCVR If the type approval of your immobilizer system is inspected in one of the countries listed in the following table, refer to the correspo.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. Y our vehicle comes with two coded keys (or three, if your vehicle is equipped with the valet feature); additional coded keys may be purchased from your authorized dealer .
Automatic arming The vehicle is armed immediately after switching the ignition to the 1 (OFF/LOCK) position. The theft indicator on the instrument panel will flash every two seconds when the vehicle is armed. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle.
1. Insert the first previously programmed coded key into the ignition and turn the ignition from 1 (OFF/LOCK) to the 3 (ON) position (maintain ignition in 3 (ON) for at least one second). 2. T urn ignition to 1 (OFF/LOCK) and remove the first coded key from the ignition.
Arming the system When armed, the perimeter alarm will notify you of an unauthorized entry . When unauthorized entry occurs, the system will flash the park lamps and will sound the horn. The system is ready to arm whenever the key is out of the ignition.
SEA TING Adjustable head restraints Head restraints help to limit head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched.
T o adjust the front seatback using the manual recliner: • Lift and hold the handle located on the side of the seat. • Lean against the seatback to adjust it to your desired position. Y ou can recline the seat back or bring it forward. • Release the handle when the desired position has been reached.
T o reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in map pocket (if equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped).
Press to move the front portion of the seat cushion up or down. Press to move the rear portion of the seat cushion up or down. Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press one side of the control to adjust firmness.
• Push the indicated side of the control for minimum heat. • Push again to deactivate. The heated seat module resets at every ignition run cycle. While the ignition is in the ON position, activating the high or low heated seat switch enables heating mode.
Y our vehicle’ s Personal Safety System 娂 consists of the following items: • Driver and passenger dual-stage airbag supplemental restraints • Front safety belts with pretensioners, energy mana.
Front crash severity sensor The front crash severity sensor enhances the ability to detect the severity of an impact. Positioned up front, it provides valuable information early in the crash event on the severity of the impact.
When the front passenger seat is occupied and the sensing system has turned off the passenger’ s frontal airbag, the “pass airbag off” indicator will light and stay lit to remind you that the front passenger frontal airbag is off. See Front passenger sensing system in the airbags section of this chapter .
• The warning light will either flash or stay lit. • The warning light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and warning light are repaired.
Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair . 1) Use the shoulder belt on the outside shoulder only . Never wear the shoulder belt under the arm.
Energy management feature • This vehicle has a seat belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision. • This seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner .
movement. For example, if the driver brakes suddenly or turns a corner sharply , or the vehicle receives an impact of approximately 5 mph (8 km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.
• Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.
Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position.
If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON... The BeltMinder 威 feature will not activate.
The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers.
Reasons given... Consider ... “I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likely to DIE.
The driver and front passenger BeltMinder 威 features can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set .
AIRBAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag.
Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries. Ford Motor Company recommends that an authorized dealer inspect all steering column assemblies in use in vehicles involved in a collision.
Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.
The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.
Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
For side airbag equipped vehicles, the front passenger sensing system will turn off the passenger seat side airbag if: • the seat is empty and safety belt is unbuckled. • a child or a small person occupies the front passenger seat and the child or small person is unbuckled.
• Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’ s frontal airbag. • If the indicator lamp remains lit even after this, the person should be advised to ride in the rear seat.
Objects Pass Airbag Off Indicator Lamp Passenger Airbag Small (i.e. 3 ring binder , small purse, bottled water) Unlit Disabled Medium (i.e. heavy briefcase, fully packed luggage) Lit Disabled Empty se.
In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat.
Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to Airbag readiness section in the Instrument Cluster chapter . Routine maintenance of the airbag is not required.
All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided. How does the side airbag system work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group.
to inflate in side-impact collisions, not roll-over , rear -impact, frontal or near -frontal collisions, unless the collision causes sufficient lateral deceleration. Several air bag system components get hot after inflation. Do not touch them after inflation.
SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags.
Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly , which could increase the risk of serious injury in a crash.
T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt.
Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child.
tether anchors. For more information on top tether straps and anchors, refer to Attaching safety seats with tether straps in this chapter . For more information of LA TCH anchors refer to Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments in this chapter .
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. T ether straps are available as an accessory for many older safety seats.
4. Open the tether anchor cover . 5. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 6. Install the child safety seat tightly using the LA TCH anchors or safety belts.
Y our vehicle has LA TCH anchors for child seat installation at the seating positions marked with the child seat symbol. The anchors on both sides of the center of the rear seat are provided for child seats at the outboard seats, and are further apart than the pairs of lower anchors for child seat installation at other seats.
If you install a child seat with rigid LA TCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat.
INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called T ire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.
Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability . • kPa: Kilopascal, a metric unit of air pressure.
gauges may be inaccurate. Ford Motor Company recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge. Use the recommended cold inflation pressure for optimum tire performance and wear . Under -inflation or over -inflation may cause uneven treadwear patterns.
T o check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump.
Improper or inadequate vehicle maintenance can cause tires to wear abnormally . Inspect all your tires, including the spare, frequently , and replace them if one or more of the following conditions ex.
This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built.
Never spin the tires in excess of the 35 mph (55 km/h) point indicated on the speedometer . Highway hazards No matter how carefully you drive there’ s always the possibility that you may eventually have a flat tire on the highway . Drive slowly to the closest safe area out of traffic.
• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires.
Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.
Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R .
12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and chains.
V ehicle Curb W eight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying.
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight.
GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear).
GVWR (Gross V ehicle W eight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
mandatory options, no cargo (internal or external), a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and T railer T owing Guide provided by your authorized dealer) for more detailed information.
capacity to carry you, 4 of your friends and all the golf bags? Y ou and four friends average 220 lb. (99 kg) each and the golf bags weigh approximately 30 lb. (13.5 kg) each. The calculation would be: 1400 – (5 x 220) – (5 x 30) = 1400 – 1100 – 150 = 150 lb.
T owing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury . The GCW of your vehicle and trailer should not exceed 6,600 lb.
T railer lamps T railer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. See your authorized dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps.
• If you will be towing a trailer frequently in hot weather , hilly conditions, at GCW , or any combination of these factors, consider refilling your rear axle with synthetic gear lube if not already so equipped. Refer to the Maintenance and specifications chapter for the lubricant specification.
RECREATIONAL TOWING (ALL WHEELS ON THE GROUND) Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground (such as behind a recreational vehicle). These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication.
STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engine and all accessories/locks the gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational.
If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’ s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine.
5. T urn the key to 3 (ON) without turning the key to 4 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. T urn the key to 3 (ON) without turning the key to 4 (ST ART).
Do not use starting fluid such as ether in the air intake system. Such fluid could cause immediate explosive damage to the engine and possible personal injury .
T o reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance information for scheduled maintenance.
Anti-lock brake system (ABS) This vehicle is equipped with an anti-lock braking system (ABS). A noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events.
W ith the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with parking brake released. (If your brake warning lamp illuminates, have your vehicle serviced immediately .
If the parking brake fails to release after completing this procedure, use the manual parking brake release lever . Pull the lever to manually release the parking brake. T RACTION CONTROL 姟 (IF EQUIPPED) Y our vehicle may be equipped with the optional T raction Control 娂 system.
During T raction Control 娂 operation you may hear an electric motor type of sound coming from the engine compartment and the engine will not “rev-up” when you push further on the accelerator .
It is also important to maintain a proper power steering fluid level in the power steering fluid reservoir: • Do not operate the vehicle with a low power steering pump fluid level (below the MIN mark on the reservoir). • Some noise is normal during operation.
This system keeps the rear of your vehicle at a constant level by automatically adding air or releasing air from the springs. If you exceed the load limit, the rear air suspension may not operate. The air suspension shut-off switch is located on the left side of the trunk.
2. Locate the access plug on the underside of the steering column cover . 3. Remove the access plug using a flat head screwdriver . Insert the screwdriver into the access hole nearest the steering wheel. Then push and hold the override button using a flat head screwdriver .
2. Insert the key and turn it to ACC. Apply the brake pedal and shift to N (Neutral) . When the key is in the ignition and in the ACC position, the automatic transmission shift lever can be moved from the P (Park) position without the brake pedal depressed.
P (Park) This position locks the transmission and prevents the rear wheels from turning. T o put your vehicle in gear: • Start the engine • Depress the brake pedal • Move the gearshift lever int.
If your vehicle is equipped with a floor -shift transmission, overdrive can be deactivated by pressing the transmission control switch on the gearshift handle. The transmission control indicator light (TCIL) will illuminate on the instrument cluster .
1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever . • W ill not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds. Forced downshifts • Allowed in (Overdrive) or Drive.
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Canadian customers refer to your Owner Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement .
• The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously .
3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. T urn the ignition to the ON position. Pause for a few seconds and return the key to the OFF position. 5. Make a further check for leaks in the fuel system.
COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 50A — — Red Red Red 60A — — Blue — Y ellow 70A — — T an — Brown 80A — — Natural — Black Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 15A T axi, Cluster , Lighting Control Module (Interior Lighting) 2 10A Ignition (ON) - Electronic Automatic T emperat.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 14 10A Ignition (ON) - BTSI (Floor -shift transmission) 15 7.5A Ignition (ON/ACC) - LCM, Door lock switch illumination,.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 25 10A Autolamp/Sunload sensor , Power mirrors, Door lock switches, Mirror switch, Keypad switch, Decklid switch, Adjus.
The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 25A* Ignition switch (Key in, RUN 1, RUN 2), Hazards 2 25A* Ignition switch (RUN/S.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 12 25A* Audio 13 20A* Instrument panel power point 14 20A* Stop lamp switch 15 20A* Heated seats 16 25A* T ray lamps (Police vehi.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 108 20A** Moonroof (non-Police vehicles only) Spotlights (available on Police vehicles, Long Wheel Base [L WB] vehicles and comme.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 204 1 ⁄ 2 ISO relay PCM 205 — Not used 206 1 ⁄ 2 ISO relay Fuel 207 — Not used 208 — Not used 209 1 ⁄ 2 ISO relay Hor.
CHANGING THE TIRES If you get a flat tire while driving: • do not brake heavily . • gradually decrease the vehicle’ s speed. • hold the steering wheel firmly .
• T ow a trailer • Use snow chains on the end of the vehicle with the dissimilar spare tire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • T ry .
When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • T owing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible.
3. Remove the spare tire and the jack. The jack could be located: • A — behind the mini spare tire or • B — behind the full size spare tire On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle.
5. Locate pry off notch (if equipped) and remove the center ornament from the aluminum wheel with the tapered end of the wheel nut wrench that came with your vehicle.
T o lessen risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is ONL Y meant for changing the tire. • Never use the rear differential as a jacking point.
Bolt size Wheel lug nut torque* lb.ft. N • m 1 ⁄ 2 x 20 100 135 * T orque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners.
3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables.
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system.
3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, o.
In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws.
achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide. However , if your warranty concern has not been resolved using the three-step procedure, you may be eligible to participate in the BBB AUTO LINE program.
The CAMV AP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings.
If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact a regional office or owner relations/customer relationship office.
(Items in this catalog may be purchased by credit card, check or money order .) Obtaining a French owner ’ s guide French Owner’ s Guides can be obtained from your authorized dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P .
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
• Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish.
• Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts.
coatings, tree sap, or other organic contamination; these contaminants may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield.
INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side airbags: • Remove dust and loose dirt with a vacuum cleaner . • Remove light stains and soil with Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54).
FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Y our Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide scheduled maintenance information which makes tracking routine service easy .
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front of the hood. 3. Lift the hood until the lift cylinders hold it open.
5. Power steering fluid reservoir 6. Engine coolant reservoir 7. Battery 8. Power distribution box 9. Engine oil filler cap 10. Automatic transmission fluid dipstick WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely .
CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. T urn the blade at a right angle to the arm. Push the lock tab (A) to release the blade from the arm loop and pull the blade down toward the windshield to remove it from the arm.
5. Locate and carefully remove the engine oil level indicator (dipstick). 6. W ipe the indicator clean. Insert the indicator fully , then remove it again.
• Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer . 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1.
economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers. T o protect your engine’ s warranty use Motorcraft SAE 5W -20 or an equivalent 5W -20 oil meeting Ford specification WSS-M2C930-A.
If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer , trouble-free operation, keep the top of the battery clean and dry . Also, make certain the battery cables are always tightly fastened to the battery terminals.
3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. T urn the A/C on and allow the engine to idle for at least one minute.
Y our vehicle was factory-filled with a 50/50 engine coolant and water concentration. If the concentration of coolant falls below 40% or above 60%, the engine parts could become damaged or not work properly . A 50–50 mixture of coolant and water provides the following: • Freeze protection down to -34°F (-36°C).
Note: Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location. Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water .
• Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant. For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool.
Y our cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage. Recycled engine coolant Ford Motor Company does NOT r.
• Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive.
1. Pull off the road as soon as safely possible and turn off the engine. 2. Arrange for the vehicle to be taken to an authorized dealer . 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low .
Automotive fuels can cause serious injury or death if misused or mishandled. Fuel ethanol and gasoline may contain benzene, which is a cancer -causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle.
• FFV fuel tanks may contain zero to 85 percent ethanol. Any fuel blends containing gasoline and ethanol should be treated the same as “Fuel Ethanol ”. T o identify if your vehicle is an FFV , check your VIN or the label on the inside of your fuel filler door .
Refueling Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off yo.
If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used.
Octane recommendations Do not be concerned if your engine sometimes knocks lightly . However , if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your authorized dealer to prevent any engine damage.
FFV engine (if equipped) Y our FFV will operate well on ordinary “Regular” unleaded gasoline, but only the highest quality fuel ethanol will provide the same level of protection and performance. T o identify if your vehicle is an FFV , check your VIN or the label on the inside of your fuel filler door .
Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill capacities section of this chapter . The advertised capacity is the amount of the indicated capacity and the empty reserve combined.
5. Follow one of the simple calculations in order to determine fuel economy: Calculation 1: Divide total miles traveled by total gallons used. Calculation 2: Multiply liters used by 100, then divide by total kilometers traveled. Keep a record for at least one month and record the type of driving (city or highway).
Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy . • Use recommended engine oil. Refer to Lubricant specifications in this chapter . • Perform all regularly scheduled maintenance items.
EMISSION CONTROL SYSTEM Y our vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards.
it from working. Information about your vehicle’ s emission system is on the V ehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and gives some tune up specifications. Please consult your W arranty Guide for complete emission warranty information.
condition. T o ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: • First, at least 10 minutes of driving on an expressway or highway . • Next, at least 20 minutes driving in stop-and-go, city-type traffic with at least four idle periods.
BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels below the “MAX” line that do not trigger the brake system warning lamp are within the normal operating range, there is no need to add fluid.
Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 50°F (10°C). Correct fluid level The transmission fluid should be checked at normal operating temperature 150°F-170°F (66°C-77°C) on a level surface.
High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition.
Changing the air filter element 1. Release the clamps that secure the air filter housing cover . 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4. W ipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing.
For PCV valve replacement, see your authorized dealer . Refer to scheduled maintenance information for the appropriate intervals for changing the PCV valve. Replace the PCV valve with one that meets Ford material and design specifications for your vehicle, such as a Motorcraft or equivalent replacement part.
Fluid Ford Part Name Capacity Fuel tank N/A 19.0 gallons (71.9L) Rear axle lubricant 5 Motorcraft SAE 80W -90 Premium Rear Axle Lubricant 5.0 pints (2.4L) 7 W indshield washer fluid Motorcraft Premium W indshield W asher Concentrate Fill to line on reservoir 1 Use only brake fluids certified to meet Ford specifications.
LUBRICANT SPECIFICATIONS Item Ford part name Ford part number Ford specification Brake fluid Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid 1 PM-1 ESA-M6C25-A Door weatherstrips Silicone Spray Lubricant XL-6 ESR-M13P4-A Engine coolant Motorcraft Premium Gold Engine Coolant (yellow-colored) VC-7-A (U.
Item Ford part name Ford part number Ford specification Automatic transmission (4R75E) Motorcraft MERCON 威 V AT F 3 XT -5-QM MERCON 威 V Rear Axle Lubricant Motorcraft SAE 80W -90 Premium Rear Axle.
ENGINE DATA Engine 4.6L V8 engine 4.6L FFV V8 engine Cubic inches 281 281 Required fuel 87 octane 87 octane or Ethanol (E 85) Firing order 1-3-7-2-6-5-4-8 1-3-7-2-6-5-4-8 Ignition system Coil on plug Coil on plug Spark plug gap 0.052–0.056 inch (1.32–1.
IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
V ehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number . The V ehicle Identification Number (VIN) contains the following information: 1.
T RANSMISSION/T RANSAXLE CODE DESIGNATIONS Y ou can find a transmission/transaxle code on the Safety Compliance Certification Label. The following table tells you which transmission or transaxle each code represents.
GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local authorized Ford or Ford of Canada dealer .
Peace of mind First aid and safety kits Full vehicle covers Locking gas cap Remote start V ehicle security systems Mobile-Ease 娂 hands-free communication system For maximum vehicle performance, keep.
A ABS (see Brakes) ..................... 173 Air cleaner filter ............... 250–251 Air conditioning .......................... 37 Air suspension ...........................177 description .............................. 177 Airbag supplemental restraint system .
Climate control (see Air conditioning or Heating) ............37 Clock adjust 6-CD in dash .............................33 AM/FM ....................................... 18 AM/FM/Cassette ........................ 19 AM/FM/CD ...........................
F Fail safe cooling ........................ 234 Flexible Fuel V ehicle (FFV) ....235 Floor mats ................................... 82 Fluid capacities ......................... 252 Fuel ............................................ 235 calculating fuel economy .
autolock ..................................... 90 keypad ....................................... 91 programming entry code ......... 91 Keys ....................................... 83, 96 positions of the ignition ......... 168 L Lamps autolamp system .
Relays ................................ 187, 195 Remote entry system ................. 86 illuminated entry ......................89 locking/unlocking doors ........... 86 opening the trunk ..................... 87 replacement/additional transmitters .
trailer towing .......................... 163 wrecker .................................... 207 T raction control ........................ 175 T raction-lok rear axle ............... 178 T ransmission ............................. 178 brake-shift interlock (BSI) .
268.
269.
270.
271.
272.
An important point after buying a device Ford 2006 Crown Victoria (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ford 2006 Crown Victoria yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ford 2006 Crown Victoria - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ford 2006 Crown Victoria you will learn all the available features of the product, as well as information on its operation. The information that you get Ford 2006 Crown Victoria will certainly help you make a decision on the purchase.
If you already are a holder of Ford 2006 Crown Victoria, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ford 2006 Crown Victoria.
However, one of the most important roles played by the user manual is to help in solving problems with Ford 2006 Crown Victoria. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ford 2006 Crown Victoria along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
