Instruction/ maintenance manual of the product 2002 Explorer Ford
Go to page of 336
Before driving Introduction 2 Instrumentation 6 Controls and features 31 Seating and safety restraints 135 Starting and driving Starting 182 Driving 187 Roadside emergencies 225 Servicing Maintenance and care 251 Capacities and specifications 304 Customer assistance 313 Reporting safety defects 325 Index 326 All rights reserved.
The following warning may be required by California law: CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
BREAKING-IN YOUR VEHICLE There are no particular guidelines for breaking-in your vehicle. During the first 1,600 km (1,000 miles) of driving, vary speeds frequently . This is recommended to give the moving parts a chance to break in. INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation W.
V ehicle Symbol Glossary Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open W.
Headlamp control (pg. 31) W iper/washer control (pg. 97) T urn signal lever (pg. 91) Instrument cluster (pg. 8) Steering wheel controls* (pg. 98) Driver air bag (pg. 163) Speed controls (pg. 92) Reverse sensing system* (pg. 33) Instrument panel dimmer control (pg.
Gearshift (including overdrive button) (pg. 196) Message center (pg. 19) Audio system (pg. 55) 4wd control* (pg. 201) Climate controls (pg. 36) Power adjustable foot pedals* (pg.
W ARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Service engine soon Illuminates briefly to ensure the system is functional. If it comes on after the engine is started, one of the engine’ s emission control systems may be malfunctioning.
3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the fuel cap.
Air bag readiness Illuminates to confirm that the air bags (front or side) are operational. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately . Safety belt Illuminates to remind you to fasten your safety belts.
Oil pressure/Engine coolant Illuminates when the engine coolant temperature is above the normal range or the engine oil pressure is outside normal range. Check the engine oil and coolant level refer to Adding engine oil and Adding coolant in the Maintenance and care chapter .
Low washer fluid (if equipped) Illuminates when the windshield washer fluid is low . Charging system Illuminates when the battery is not charging properly . AdvanceT rac Y (if equipped) Flashes when the AdvanceT rac y system is active. If the light remains on, have the system serviced immediately .
O/D off (if equipped) Illuminates when the overdrive function has been turned OFF using the T ransmission Control Switch (TCS) on end of gearshift. If the light does not come on or the light flashes steadily , have your vehicle serviced as soon as possible, as damage to the transmission could occur .
GAUGES Standard instrument cluster gauges Optional instrument cluster gauges Speedometer Indicates the current vehicle speed. O/D OFF DOOR AJAR CHECK GAGE 4X4 LOW 4X4 HIGH CHECK FUEL CAP LOW WASH BRAK.
Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the indicated area between the “H” and “C”). If it enters the red section, the engine is overheating.
T rip odometer Registers the kilometers (miles) of individual journeys. • Standard instrument cluster Press and release the SELECT/RESET button to toggle between the odometer and trip odometer display .
Engine oil pressure gauge Indicates engine oil pressure. At normal operating temperature, the needle will be in the normal range (the area between the “L” and “H”); if the needle goes below the normal range, stop the vehicle as soon as safely possible and switch off the engine immediately .
Usually , when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary . Refer to Compass calibration adjustment.
Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut.
Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu. Info menu This control displays the following control displays: • Odometer/Compass .
degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error . Refer to Compass zone/calibration adjustment. Compass zone/calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines.
9. Slowly drive the vehicle in a circle (less than 5 km/h [3 mph]) until the CIRCLE SLOWL Y TO CALIBRA TE indicator changes to CALIBRA TION COMPLETED. This will take up to three circles to complete calibration.
Trip elapsed drive time Select this function from the INFO menu to display a timer . T o operate the T rip Elapsed Drive T ime perform the following: 1. Press and release RESET in order to start the timer . 2. Press and release RESET to pause the timer .
Autolocks 1. Select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the autolocks ON or OFF . Easy entry/exit 1. Select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the easy entry/exit feature ON or OFF .
Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric. System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored.
W arning messages that have been reset are divided into three categories: • They will reappear on the display every minute from the reset. • They will reappear on the display ten minutes from the reset. • They will not reappear until an ignition OFF-ON cycle has been completed.
CHECK ENGINE TEMPERA TURE. Displayed when the engine coolant is overheating. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and care chapter .
CHECK TIRE PRESSURE (if equipped). Displayed when any of the tire pressures are high or low . Refer to Checking the tire pressure in the Maintenance and care chapter . CHECK SP ARE TIRE PRESSURE (if equipped). Displayed when the spare tire pressure is high or low .
T o reset the oil monitoring system to 100% after each oil change [approximately 8,000 km (5,000 miles) or 180 days] perform the following: 1. Press the SETUP control to access the System Check function. 2. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”.
4. Release the RESET control momentarily , then press RESET and SETUP controls at the same time to activate a service mode which will display OIL LIFE XX% RESET TO AL TER. 5. Press RESET until you find your personalized OIL LIFE XX%. 6. W ith your personalized OIL LIFE XX% displayed, press SETUP to continue the system check.
HEADLAMP CONTROL Rotate the headlamp control clockwise to the first position to turn on the parking lamps. Rotate clockwise to the second position to also turn on the headlamps. Foglamp control (if equipped) The headlamp control also operates the foglamps.
High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp parklamp operation.
AUTOLAMP CONTROL The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for approximately 20 seconds or a programmed time delay after the ignition switch is turned to the OFF position.
• the vehicle is moving in reverse at a speed of less than 5 km/h (3 mph) and a moving object is approaching the rear of the vehicle at a speed of less than 5 km/h (3 mph) The RSS is not effective at speeds greater than 5 km/h (3 mph) and may not detect certain angular or moving objects.
The RSS detects obstacles within approximately 1.8 meters (5.9 ft.) of the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases.
CLIMATE CONTROL SYSTEM Manual heating and air conditioning system (if equipped) Fan speed control Controls the volume of air circulated in the vehicle. T emperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. • MAX A/C-Uses recirculated air to cool the vehicle.
• (Defrost)-Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the outside temperature is about 6°C (43°F) or higher , the air conditioner will automatically dehumidify the air to reduce fogging.
Operating tips • In humid weather conditions, place the climate control system in before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate control system as desired.
4. Set the fan speed to High 5. Direct the outer panel vents towards the side windows 6. T o increase airflow to the outer panel vents, close the central panel vents. Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop.
Turning the DEA TC system on Press AUTO, any of the override controls, the fan speed control, or either of the temperature selection controls. The DEA TC system will only operate when the ignition is in the ON position. Turning the DEA TC system off Press OFF .
DEA TC automatic operation Press AUTO and select the desired temperature. The selected temperature will appear in the display window , and an indicator above the AUTO control will light. The DEA TC system will either heat or cool the vehicle to achieve the selected temperature.
Single/dual electronic temperature zone Press DUAL to enable or disable the dual zone temperature feature. When DUAL is pressed, the display window indicates the current temperature setting for the driver and the last temperature setting that was selected for the passenger .
Passenger side temperature selection T o control the temperature, select any temperature between 16°C (60°F) and 32°C (90°F) by pressing the temperature control on the passenger side of the system.
Fan speed ( ) When AUTO is pressed, fan speed is adjusted automatically for existing conditions. Y ou can override fan speed at any time. T o control fan speed manually , press the fan control to cancel the automatic fan speed operation. Press the control up for higher fan speed or down for lower fan speed.
In and , if the outside temperature is about 6°C (43°F) or higher , the air conditioner will automatically dehumidify the air to reduce fogging. However , the A/C indicator will be off and the A/C override control cannot be selected. The air conditioning compressor can operate in all modes except OFF .
indicator will not be lit. If the recirculated air is selected while in AUTO operation, the DEA TC system will be disabled and you will return to manual operation with the recirculated air indicator lit and with the A/C operating. T o return to automatic recirculated air operation, press AUTO.
ducts. If the temperature is about 6°C (43°F) or higher , the air conditioner will automatically dehumidify the air to reduce fogging. (Note that the A/C indicator does not illuminate when this mode is selected.) Recirculation and A/C override controls cannot be selected.
If the outside temperature is displayed while the DEA TC system is in the OFF mode and the DEA TC is turned on, the driver and passenger temperatures will be displayed for 4 seconds. Following this, the outside temperature display will return to the window .
objects may fall down into the defroster outlets and block airflow , in addition to damaging the climate control system. T o aide in side window defogging/demisting in cold weather conditions: 1. Select 2. Set the temperature control to full heat 3. Select A/C 4.
T o control the auxiliary climate control system from the front controls, turn the fan speed control knob to the desired speed. T urn the temperature control to regulate the air temperature. Press the mode selector once to select air distribution through the overhead vents.
Ensure that the front auxiliary control is turned to REAR to enable the rear climate controls. T urn the fan speed control to the desired fan speed. T urn the temperature control to regulate the air temperature. Press the mode selector once to select air distribution through the overhead vents.
Floor console climate controls (if equipped) Depending on the equipment package, your vehicle may be equipped with floor console climate control capabilities. The floor console climate control system allows the rear passengers to select a mode of airflow distribution through the floor console.
REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • A small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear window defroster .
USING YOUR AUDIO SYSTEM AM/FM stereo cassette V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
AM/FM select The AM/FM select control works in radio and tape modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the AM control to select from AM selections, and press the FM control to select from FM1 or FM2 memory preset stations.
Scan function The scan function works in radio mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Radio station memory preset The radio is equipped with six station memory preset controls.
Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection. T o activate the feature, momentarily depress the T APE AMS button. Then, press either REW (for the beginning of the current selection) or FF (to advance to the next selection).
Eject function Press the control to stop and eject a tape. Dolby T noise reduction Dolby t noise reduction operates only in tape mode. Dolby t noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby t noise reduction.
• to decrease minutes and • to increase minutes. The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for 10 seconds, when the radio is turned on, and then revert to clock information.
T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and CD modes.
Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in CD mode • Press to listen to the next selection. • Press to listen to the previous selection.
Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur . Rewind The rewind control works in CD mode. T o rewind in CD mode, press the CD control (preset 1). Press the control again to deactivate rewind mode.
Setting the clock Press CLK to toggle between listening frequencies and clock mode while in radio mode. T o set the hour , press and hold the CLK control. Press the SEEK control: • to decrease hours and • to increase hours. T o set the minute, press and hold the CLK control.
Premium AM/FM Stereo/Cassette/Single CD V olume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the T APE/CD select control. T urn control to raise or lower volume.
AM/FM select The AM/FM select control works in radio, tape and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play .
Seek function in CD mode • Press to seek to the previous track of the disc. If a selection has been playing for three seconds or more and you press , the CD will replay that selection from the beginning. • Press to seek forward to the next track of the disc.
3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations.
Press the BASS control then press: • to decrease the bass output and • to increase the bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. Press the TREB control then press: • to decrease the treble output and • to increase the treble output.
Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the F ADE control then press: • to shift the sound to the front and • to shift the sound to the rear . T ape/CD select • T o begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the T APE control.
Fast forward The fast forward control works in tape and CD modes. • In the tape mode, tape direction will automatically reverse when the end of the tape is reached. • In CD mode, pressing the control fast forwards the CD within the current track. T ape direction select Press SIDE 1–2 to play the alternate side of a tape.
Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. Shuffle feature The shuffle feature operates in CD mode and plays all tracks in random order .
• to decrease minutes and • to increase minutes. If your vehicle has a separate clock, (other than the digital radio display), the CLK control will not function in the above manner . The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.
Audiophile AM/FM Stereo In Dash Six CD Radio Premium AM/FM Stereo In Dash Six CD Radio LOAD EJ SHUF COMP MUTE SEL BAL BASS FADE TREB SCAN DISC TUNE PUSH ON CD 123456 MENU AM FM SEEK REW FF Controls an.
V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Tune/disc adjust The tune control works in radio or CD mode. Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly .
Seek function in CD mode • Press to seek to the previous track of the current disc. If the beginning of the disc is reached, the CD player seeks to the beginning of the last track on the current disc and begins playing. • Press to seek forward to the next track of the current disc.
4. Press and hold a memory preset control. The playing media will mute momentarily . When the sound returns, the station is held in memory on the control you selected. The display will read SA VED. Autostore Autostore allows you to set the strongest local radio stations without losing your original manually set preset stations.
CD select CD mode may be entered by pressing the CD control and the LOAD control. Load the CD into the audio system. The first track of the disc will begin playing.
Press the LOAD control. (Y ou can choose which slot will be loaded by pressing the desired preset number . If you do not choose a slot, the system will choose the next available one.) W ait until the CD door opens. Load the CD into the player . LOADING CD# is displayed.
Rewind The rewind control works in CD modes. Press and hold the REW control until the desired selection is reached. If the beginning of the disc is reached, the CD will begin play at the first track. Release the control to disengage rewind mode. When in rewind mode, your audio system will automatically lower the volume level of the playing media.
when COMP OFF is displayed. Press the SEL control again to disable the feature when COMP ON is displayed. On Premium audios, press the COMP control until COMP ON is displayed. Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output.
Menu mode The MENU control allows you to access many different features within your audio system. There are three sets of menus available depending upon which mode or feature is activated. While in FM mode, two menus are available. If RDS is turned OFF , you can access the following: • SELECT HOURS — Refer to Setting the clock.
Radio data system (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations. T o activate RDS: • When in FM mode, press the MENU control until RDS OFF displays. • Press the SEL control to engage this feature (RDS ON).
Press the MENU control until FIND program type is displayed. Use the SEL control to select the program type. W ith the feature on, use the SEEK or SCAN control to find the desired program type from th.
Press the DSP control to access one of the following modes: • DSP OFF • SIGNAL MODE • OCCUP ANCY MODE Use the SEL control to select the desired signal mode (the selected mode will appear in the display).
Use the SEL control to manually set the time. • Press to increase hours/minutes. • Press to decrease hours/minutes. Press the MENU control again to disengage the clock mode. T roubleshooting the CD changer (if equipped) The laser beam used in the compact disc player is harmful to the eyes.
CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players.
(24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations. • T errain. Hills, mountains and tall buildings between your vehicle’ s antenna and the radio station signal can cause FM reception problems.
POSITIONS OF THE IGNITION 1. OFF/LOCK, shuts off the engine and all accessories/locks the steering wheel, gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. 3.
T o turn speed control off • Press OFF • Speed control automatically defaults to OFF when the ignition is turn off. Once speed control is switched off, the previously programmed set speed will be erased.
T o set a higher set speed • Press and hold SET +. Release the control when the desired vehicle speed is reached or • Press and release SET + to operate the T ap-Up function. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal.
T o disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed.
T o return to a previously set speed • Press RES. For RES to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when the vehicle speed control is engaged and actively controlling vehicle speed.
If your vehicle has the tilt-only steering column, pull the lever down to unlock the steering column. While the lever is in the down position, tilt the steering column to its desired orientation. Lift the lever back to its original position to lock the steering column.
Push (tap) the end of the stalk briefly for a single swipe (no wash). Push and hold for three swipes with wash. Push and hold for a longer wash (up to ten seconds). Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle’ s speed changes.
Audio control features Press to select: • AM, FM1, FM2, • T APE (if equipped), • CD (if equipped), or • DVD (if equipped). In AM, FM1, or FM2 mode: • Press MEM to select preset stations within the selected radio band. In T ape mode: • Press MEM to select the next selection on the tape.
Climate control features Press TMP + or - to adjust temperature. Press + or - to adjust fan speed. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’ s overhead console will vary according to your option package.
Storage compartment Press the latch to open the storage compartment. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Place the V elcro hook onto the side of the aftermarket transmitter opposite of the button.
Moon roof (if equipped) Y ou can move the glass panel of the moon roof back to open or tilt up to ventilate the vehicle. T o open the moon roof: The moon roof is equipped with an automatic, one-touch, express opening feature. Press and momentarily hold the rear portion of the control.
The map lamp controls are located on the dome lamp. Press the controls on either side of each lens on each map lamp to activate the lamps. All vehicles are equipped with a cargo lamp, which is located overhead in the rear cargo area and above the the third row seat (if equipped).
Do not use the HomeLink t Universal T ransceiver with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982).
3. Simultaneously press and hold both the HomeLink t and hand-held transmitter button. Do not release the buttons until step 4 has been completed. Some entry gates and garage door openers may require you to replace step 3 with procedures noted in the “Gate Operator and Canadian Programming” section for Canadian residents.
Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink t to accept the signal from the hand-held transmitter .
Erasing HomeLink T buttons T o erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink t buttons until the red indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.
ILLUMINATED VISOR MIRROR (IF EQUIPPED) T o turn on the visor mirror lamps, lift the mirror cover . POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open.
One touch down • Press AUTO completely down and release quickly . The driver’ s window will open fully . One touch down can be deactivated during operation by pushing down on the top part of the driver power window control. Window lock The window lock feature allows only the driver to operate the power windows.
POWER DOOR LOCKS Press control to unlock all doors. Press control to lock all doors. POWER DOOR LOCK/UNLOCK INHIBIT If the interior trim switch does not operate, see the Perimeter alarm system in this section for more details. LIFTGATE An additional power door lock can be accessed by opening the liftgate.
CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door .
Heated outside mirrors R (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
Auxiliary power point Power outlets are designed for accessory plugs only . Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty . The power point is an additional power source for electrical accessories.
POSITIVE RETENTION FLOOR MA T Position the driver floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
Make sure the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. CARGO COVER (IF EQUIPPED) Y our vehicle may be equipped with a cargo area cover that covers the luggage compartment of your vehicle.
7 passenger stowage: 1. T o open, lift the release handle and the lid. 2. T o close, lower the lid, lift the release handle and press down on the lid. 5 passenger stowage: When the lid is open, it will stand up on its own. The lid can be detached from the vehicle and used as a knee pad (carpet side up) for changing a tire.
Unlocking the doors/liftgate Press this control to unlock the driver’ s door . The interior lamps will illuminate with the ignition OFF . Press the control a second time within three seconds to unlock all doors and liftgate. Locking the doors/liftgate Press this control to lock all doors and liftgate.
Opening the liftgate window Press the control to unlatch the liftgate window . Sounding a panic alarm Press this control to activate the alarm. The personal panic alarm will cycle the horn and turn signals on/off, plus illuminate the interior lights. T o deactivate the alarm, press the control again or turn the ignition to ACC or ON.
Activating the memory seat feature T o activate this feature: 1. Position the seat to the position you desire. 2. Press the SET control on the driver’ s door panel.
T o replace the battery: 1. T wist a thin coin between the two halves of the transmitter near the key ring. DO NOT T AKE THE FRONT P ART OF THE TRANSMITTER AP ART . 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit.
T o program the transmitters yourself: • Insert a key in the ignition and turn from 1 (LOCK) to 3 (ON) and cycle between 1 (LOCK) and 3 (ON) eight times in rapid succession (within 10 seconds) with the eighth turn ending in the 3 (ON) position. The doors will lock/unlock to confirm that programming mode has been entered.
KEYLESS ENTRY SYSTEM (IF EQUIPPED) W ith the keyless entry keypad, you can: • lock or unlock the vehicle doors and liftgate without using the key . • open the liftgate window . • disable/enable autolock. • arm and disarm the perimeter alarm system (if equipped).
Programming your own personal entry code 1. Enter the factory-set code (keypad will illuminate when pressed). 2. Press the 1/2 control within five seconds of step 1. 3. Enter your personal 5 digit code. Enter each digit within five seconds of the previous one.
If you wish to erase your personal code, use the following instructions: Erasing personal code 1. Enter the factory-set code. 2. Press 1/2 within five seconds of step 1 and release. 3. Press the 1/2 control and hold for 2 seconds to erase the customer programmed keycode, within five seconds of step 2.
Unlocking the doors and liftgate or the liftgate window with the keyless entry system The driver’ s door must be unlocked before any other . If more than five seconds pass between pressing numbers, enter the code again. The system has shut down if the keypad light is out.
Locking the doors and liftgate, press the 7/8 and 9/0 controls at the same time. This can be done only when the driver’ s door is closed. Autolock The autolock feature will lock all of the vehicle d.
Power door unlock/lock procedure Y ou must complete steps 1-5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. 1. T urn the ignition key to ON. 2. Press the power door unlock control three times.
PERIMETER ALARM SYSTEM The perimeter anti-theft system will help prevent your vehicle from unauthorized entry . If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are brought to the dealership, to aid in troubleshooting.
Arming the system When armed, this system will help protect your vehicle from unauthorized entry . When unauthorized entry occurs, the system will flash the headlamps and/or parking lamps, and will chirp the horn. The system is ready to arm whenever the key is removed from the ignition.
Disarming the system Y ou can disarm the system by any of the following actions: • Unlock the doors by using your remote entry transmitter . • Unlock the doors by using your keyless entry pad. • Unlock the driver’ s door with a key . T urn the key full travel (toward the front of the vehicle) to make sure the alarm disarms.
• Press the P ANIC control on the remote entry transmitter . This will only shut off the horn and parking lamps when the alarm is sounding. The alarm system will still be armed. • Press the liftgate window control on the remote entry transmitter .
• When the ignition is in the OFF position, the indicator will flash once every 2 seconds to indicate the SecuriLock y system is functioning as a theft deterrent. • When the ignition is in the ON position, the indicator will glow for 3 seconds to indicate normal system functionality .
If any of these items are present, you need to keep these objects from touching the coded key while starting the engine. These objects and devices cannot damage the coded key , but can cause a momentary “no start” condition if they are too close to the key during engine start.
1. Insert the first previously programmed coded key into the ignition and turn the ignition from 2 (ACC) to 3 (ON) (maintain ignition in 3 (ON) for at least one second). 2. T urn ignition to 1 (LOCK) and remove the first coded key from the ignition. 3.
SEA TING Front seat Adjustable head restraints (if equipped) Y our vehicle’ s front seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision.
Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. The control is located on the outboard side of the seat cushion.
Press the control to move the seat forward, backward, up or down. Memory seat/easy entry/exit feature (if equipped) This system allows automatic positioning of the driver seat to three programmable positions. The memory seat control is located on the driver door .
Using the manual lumbar support T urn the lumbar support control toward the front of vehicle to move the lumbar support forward for more direct support. T urn the lumbar support control toward the rear of vehicle to move the lumbar support back for less direct support.
REAR SEATS Adjustable head restraints Y our vehicle’ s rear seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision.
1. Press the lower release control downward to unlatch the seatback. 2. Rotate the seatback downward into the load floor position. 3. Press down on the top outboard area of the seatback until a click is heard. The seat is now latched in the floor position.
T o return the seat to the upright position: • Press downward on the upper corner of the seatback and hold. • Pull the release handle upward to unlatch the seat. • Rotate the seatback upward until the seatback latches in the upright position. The seatback will click when it is locked into position.
T o return the seat to the upright position: 1. Pull the handle down and lift the seatback toward the rear of the vehicle. 2. Rotate the seatback until you hear a click, locking it in the upright position. Adjusting the 2nd row seat for E-Z Entry (if equipped) The E-Z Entry seat allows for easier entry and exit to and from the 3rd row seat.
3. T o return the seat to a seating position, flip the seat into the upright position. 4. Make sure the seat is latched to the floor . T o exit the 3rd row seat, pull the red access control lever up releasing the seat from the floor and rotate the seat up towards the front seat.
Folding the middle 2nd row seat (If equipped) 1. Locate the lever on the side of the seatback. 2. Pull the lever up and push the seatback toward the front of the vehicle. 3. Press down on the top outboard area of the seatback until a click is heard. T o return the seatback to the upright position: 1.
Third row seat (if equipped) 3rd row stow feature The 3rd row seat has a tip/stow feature to increase cargo space without removing the seat from the vehicle. T o put seat in stowed position: 1. Pull the seat release lever located on top of the seatback while pushing the seatback down onto the seat cushion.
2. Pull the seat release lever located on top of the seatback while lifting the seatback into the upright position. 3. The seatback will latch into place. The third row seat is equipped with combination lap and shoulder belts in both seating positions.
information to the Restraints Control Module (RCM). During a crash, the RCM activates the safety belt pretensioners and/or either one or both stages of the dual-stage air bag supplemental restraints based on crash severity and occupant conditions.
Front safety belt pretensioners The safety belt pretensioners are designed to tighten the safety belts firmly against the occupant’ s body during a collision. This maximizes the effectiveness of the safety belts and helps properly position the occupant relative to the air bag to improve protection.
T o reduce the risk of injury , make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving.
Energy management feature • This vehicle has a seat belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision. • This seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner .
The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described b.
How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
BEL T AND RETRACTOR ASSEMBL Y MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in W orkshop Manual. Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.
Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T o lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. T o tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips.
The lap belt will adjust automatically . T o fasten, grasp the tongue, and with a continuous motion, pull out enough webbing to buckle the tongue into the correct buckle. If you did not pull out enough webbing to reach the buckle, allow the tongue to retract fully before trying to pull it out again.
Safety belt height adjustment Y our vehicle has safety belt height adjustments for the front and second row outboard seating positions. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o lower the shoulder belt height, squeeze the button and slide the height adjuster down.
Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.
If... Then... The driver’ s safety belt is buckled before the ignition switch is turned to the ON position... The BeltMinder feature will not activate.
Reasons given... Consider ... “Belts are uncomfortable” W e design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort.
One time disable Any time the safety belt is buckled and then unbuckled during an ignition ON cycle, BeltMinder will be disabled for that ignition cycle only . Deactivating/activating the BeltMinder feature Read step s1-9 thoroughly before proceeding with the deactivation/activation programming procedure.
• This will disable BeltMinder if it is currently enabled, or enable BeltMinder if it is currently disabled. 7. Confirmation of disabling BeltMinder is provided by flashing the safety belt warning light four times per second for three seconds.
AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Y our vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems. In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity .
Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. National Highway T raffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches) between an occupant’ s chest and the driver air bag module.
Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.
The SRS consists of: • driver and passenger air bag modules (which include the inflators and air bags). • side air curtains (if equipped). Refer to Side air curtain system later in this chapter . • one or more impact and safing sensors. • a readiness light and tone.
Safety Canopy Y system (if equipped) Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying Safety Canopy y . Failure to follow these instructions may increase the risk of personal injury in the event of a collision.
How does the Safety Canopy Y system work? The design and development of the Safety Canopy y system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group.
close an electrical circuit that initiates Safety Canopy y inflation or when a certain likelihood of a rollover event is detected by the rollover sensor . The Safety Canopy y is mounted to the roof side-rail sheet metal, behind the headliner , above the first and second row seats.
Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Air bag readiness section in the Instrumentation chapter . Routine maintenance of the air bag is not required.
Always follow the instructions and warnings that come with any infant or child restraint you might use. When possible, always place children under age 12 in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating positions.
Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the sea.
The shoulder belt should cross the chest, resting snugly on the center of the shoulder . The lap belt should rest low and snug across the hips, never up high across the stomach. If the booster seat slides on the vehicle seat, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition.
safety seat you put in your vehicle. If you do not install and use the safety seat properly , the child may be injured in a sudden stop or collision. When installing a child safety seat: • Review and follow the information presented in the Air bag supplemental restraint system (SRS) section in this chapter .
Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat.
5. If you have not pulled out enough webbing to reach, allow the webbing to fully retract before attempting to pull it out again and repeat steps 2 through 4. 6. Pull the webbing through the child seat toward the retractor while pushing down with your knee on the child seat.
Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor . 1. Position the child safety seat on the rear seat cushion. 2. Route the tether strap under the head restraint and between the head restraint posts.
• At the rear of the cargo area 4. Clip the tether strap to the anchor . If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision.
PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
• Make sure the parking brake is set. • Make sure the gearshift is in P (Park). 3. T urn the key to 3 (ON) without turning the key to 4 (ST ART). 4 3 2 1 O/D OFF DOOR AJAR CHECK GAGE 4X4 LOW 4X4 H.
Make sure the corresponding lights illuminate or illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE Note: Whenever you start your vehicle, release the key as soon as the engine starts.
Cold weather starting (flexible fuel vehicles only) As the outside temperature approaches freezing, ethanol fuel distributors should supply winter grade ethanol (same as with unleaded gasoline).
T o prevent electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. T ake precautions to avoid its dangerous effects.
BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system.
The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency . The wheels are prevented from locking even when the brakes are firmly applied.
Brake Assist (if equipped as part of the AdvanceT rac Y system) The Brake Assist system provides full braking force during panic braking situations. It detects a rapid application of the brake pedal and maximizes the amount of brake booster assist, helping the driver to achieve maximum braking pressure.
Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy . ADVANCET RAC STABILITY ENHANCEMENT SYSTEM (IF EQUIPPED) The AdvanceT rac y system provides a stability enhancement feature as well as a traction enhancement feature.
Driving conditions which may activate AdvanceT rac y include: • T aking a turn too fast • Maneuvering quickly to avoid an accident, pedestrian or obstacle • Hitting a patch of ice • Changing l.
spin. If your vehicle seems to lose engine power while driving in deep sand or very deep snow , switching off the AdvanceT rac y stability enhancement feature will restore full engine power and will enhance momentum through the obstacle.
STEERING Y our vehicle is equipped with power steering. Power steering uses energy from the engine to decrease the driver’ s effort in steering the vehicle. T o prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
Loaded vehicles, with a higher center of gravity , may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle. Y our vehicle has the capability to haul more cargo and people than most passenger cars.
3. Rotate the access panel (counterclockwise) with a flat head screw driver until it is lined up to the access hole in the open position. 4. Insert a tool (or screw driver) into the access hole to override the brake-shift interlock. Apply the brake and shift into Neutral.
If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear . Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur .
P (Park) T o put your vehicle in gear , start the engine, depress the brake pedal, then move gearshift lever out of P (Park). Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This position locks the transmission and prevents the rear wheels from turning.
Drive (overdrive deactivated) Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift lever in the D(Drive) position. The transmission with overdrive off operates in gears one through four , providing more engine braking than D(Drive) with Overdrive ON and is useful whenever driving conditions (i.
Forced Downshifts T o gain acceleration in (Overdrive) or Drive (O/D OFF) when passing another vehicle, push the accelerator to the floor . The transmission will downshift to the appropriate gear: fourth, third, second or first gear .
2. Engage the parking brake. 3. Shift into 1 (First). 4. T urn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone.
Maximum downshift speeds Shift from: T ransfer case position (if equipped) AUTO or HIGH LOW 5 (Overdrive) - 4 88 km/h (55 mph) 34 km/h (21 mph) 4 - 3 72 km/h (45 mph) 27 km/h (17 mph) 3 - 2 56 km/h (35 mph) 21 km/h (13 mph) 2 - 1 32 km/h (20 mph) 11 km/h (7 mph) Reverse Ensure that the vehicle is at a complete stop before shifting into R (Reverse).
Positions of the Control-T rac system The Control-T rac system functions in three modes: • The 4x4 Auto mode provides four -wheel drive with full power delivered to the rear axle, and to the front axle as required for increased traction.
• The 4x4 Low mode supplies four -wheel drive with full power to both axles and includes a lower gear ratio for low-speed. It is only intended for off-road applications that require extra power including deep sand, steep grades and pulling a boat and trailer out of the water .
Using the Control Trac 4WD system 4X4 AUTO - Power to all four wheels; used for normal street and highway driving. 4X4 HIGH (4WD High) - Used for extra traction such as in snow or icy roads or in off-road situations. Not intended for use on dry pavement.
Using the Control T rac system Shifting between 4x4 Auto and 4x4 High When you press the 4x4 High button, the indicator light will illuminate in the instrument cluster . When you press the 4x4 Auto button, the indicator light will turn off. Either shift can be done at a stop or while driving at any speed.
Shifting from 4x4 Low to 4x4 Auto or 4x4 High 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Press the 4x4 Auto or the 4x4 High button.
steering and braking control of your vehicle, you must have all four wheels on the ground and they must be rolling, not sliding or spinning. Basic operating principles • Do not use 4WD on dry , hard surfaced roads. Doing so will produce excessive noise, increase tire wear and may damage drive components.
Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly .
the driveline. Therefore, the vehicle is free to roll even if the automatic transmission is in P (Park) or the manual transmission is in gear . Do not leave the vehicle unattended with the transfer case in N (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle.
Mud and water If you must drive through high water , drive slowly . T raction or brake capability may be limited. When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly . If the ignition system gets wet, the vehicle may stall.
possibly rolling over . Whenever driving on a hill, determine beforehand the route you will use. Do not drive over the crest of a hill without seeing what conditions are on the other side. Do not drive in reverse over a hill without the aid of an observer .
A void sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop.
These “aftermarket lift kits” could adversely affect the vehicle’ s handling characteristics, which could lead to loss of vehicle control or roll over and serious injury . T ires can be damaged during off-road use. For your safety , tires that are damaged should not be used for highway driving because they are more likely to blow out or fail.
Ford Motor Company recommends that caution be used with any vehicle equipped with a high load or device (such as ladder racks or pickup box cover). Failure to maintain your vehicle properly may void the warranty , increase your repair cost, reduce vehicle performance and operational capabilities and adversely affect driver and passenger safety .
• GCWR (Gross Combined W eight Rating): Maximum permissible combined weight of towing vehicle (including occupants and cargo) and the loaded trailer . • Maximum T railer W eight Rating: Maximum weight of a trailer the vehicle is permitted to tow .
Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Special loading instructions for owners of pickup trucks and utility-type vehicles For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in this chapter .
Once through the water , always try the brakes. W et brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal.
T owing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover , personal injury or death.
4x2 w/automatic transmission GCWR (Gross Combined W eight Rating)/T railer W eight *-When towing maximum loads under high outside temperatures and on steep grades, the A/C system may cycle on and off to protect the engine from overheating. This may result in a temporary increase of interior temperatures.
4x4 w/automatic transmission GCWR (Gross Combined W eight Rating)/T railer W eight Engine Rear axle ratio Maximum GCWR-kg (lbs.) T railer weight range-kg (lbs.) (0-Maximum) Notes: - For high altitude operation, reduce GCW by 2% per 300 meters (1000 ft) elevation.
Hitches Do not use hitches that clamp onto the vehicle bumper . Use a load carrying hitch. Y ou must distribute the load in your trailer so that 10–15% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’ s safety chains to the frame or hook retainers of the vehicle hitch.
• Consult your local motor vehicle speed regulations for towing a trailer . • T o eliminate excessive shifting, use a lower gear . This will also assist in transmission cooling. (For additional information, refer to the Driving with a 4–speed automatic transmission section in this chapter .
Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability , emissions and reliability . Replace the rear axle lubricant any time the axle has been submerged in water .
LUGGAGE RACK Y our vehicle is equipped with a roof rack. The maximum recommended load is 90 kg (200 lbs), evenly distributed. If it is not possible to distribute the load, position it as far rearward as possible. Use the tie down loops on the thumbwheels (if equipped) to secure the load.
Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. T o obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140.
The fuel pump shut-off switch is located in the passenger’ s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. T urn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button.
Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Passenger compartment fuse panel The fuse panel is located below the instrument panel on the driver’ s side. T o remove a fuse use the fuse puller tool provided on the fuse panel box.
The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 30A Memory seat module 2 20A Heated seats, Moonroof 3 20A Radio, Amplifier , Power an.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 22 10A ABS, IVD Controller 23 15A Brake pedal position switch, Driver brake applied relay , Redundant cruise deactivate switch 24 15A Cigar lighter , OBD II 25 5A Mode-T emperature actuator for auxiliary climate control, T railer tow battery charge coil 26 7.
Passenger compartment fuse panel (top side) These relays are located on the reverse side of the passenger compartment fuse panel. T o access the relays you must remove the passenger compartment fuse panel.
Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’ s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 60A** PJB 2 30A** BSM 3 20A** GCC pusher fan (export only) 4 30A** Rear defrost 5 .
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 28 20A* Horn relay 29 60A** PJB 30 20A** Rear wiper motor 31 — Not used 32 — Not used 33 30A** Auxiliary blower motor 34 30A*.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 59 — Driver brake applied or DRL relay (Canada only) 60 — PCM diode 61 — A/C clutch diode 62 30A CB Delayed accessory * Mini Fuses ** Maxi Cartridge Fuses Rear Relay Box The relay box is located on the rear passenger side quarter trim panel.
Fuse/Relay Location Description Relay 21 Not used Relay 22 Approach lamps Relay 23 Not used Diode 3 Not used Diode 4 Not used Auxiliary relay box (Canadian vehicles equipped with AdvanceTrac Y only) The relay box is located on the front right fender well underneath the speed control module.
The use of tire sealants is not recommended and may compromise the integrity of your tires. The use of tire sealants may also affect your tire pressure monitoring system (if equipped).
Removing the jack 1. Open liftgate and remove the carpeted floor lid and jack cover . 2. T urn jack screw eyelet counterclockwise and remove the jack from the bracket. 3. Remove the lug wrench from the bag and rotate the wrench socket out from the handle.
3. T urn the wrench counterclockwise until tire is lowered to the ground making sure the other end of the wrench does not scuff kick plate, the tire can be slid rearward and the cable is slightly slack. 4. Lift tire on one side and remove the retainer from the spare tire.
1. Park on a level surface, activate hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park) or in the reverse gear (manual transmission) and turn engine OFF .
6. Assemble the jack handle extension on the lug nut wrench by sliding the square end of the jack handle through the plastic grommet on the lug nut wrench and into the square hole on the other side.
T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the front or rear differential as a jacking point.
2. Slide the wheel under the vehicle and install the retainer through the wheel center . 3. T urn the lug wrench clockwise until the tire is raised to its original position underneath the vehicle. The lug wrench will click when the tire is raised to the stowed position.
4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. T urn the heater fan on in both vehicles to protect any electrical surges. T urn all other accessories off.
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to the provided jumpstarting bolt ONL Y . Connecting to any other exposed component may cause an explosion.
4.0L Engine 4.6L Engine Roadside emergencies 247.
5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle.
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a scheduled maintenance guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Working with the engine on • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly . Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running.
2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood. Maintenance and care 253.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Engine coolant reservoir 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake fluid reservoir 5. Power distribution box 6. Battery 7. Power steering fluid reservoir 8. Air filter assembly 9.
4.6L V8 engine 1. Engine coolant reservoir 2. Engine oil dipstick 3. Clutch fluid reservoir (if equipped) 4. Brake fluid reservoir 5. Power distribution box 6. Battery 7. Power steering fluid reservoir 8. Engine oil filler cap 9. Air filter assembly 10.
ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. T urn the engine off and wait a few minutes for the oil to drain into the oil pan.
• 4.6L V8 engine 6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range .
• 4.0L SOHC V6 engine • 4.6L V8 engine • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil.
3. Recheck the engine oil level. Make sure the oil level is not above the MAX hole on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise 1/4 of a turn or until three clicks can be heard.
4.0L Engine Look for this certification trademark. SAE 5W -30 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use Motorcraft or an equivalent oil meeting Ford Specification WSS-M2C205–H.
BRAKE FLUID AND CLUTCH FLUID Checking and adding brake fluid/clutch fluid When equipped with a manual transmission, your vehicle uses the same reservoir for brake and clutch fluid. Brake/clutch fluid should be checked and refilled as needed. Refer to the scheduled maintenance guide for the service interval schedules.
WINDSHIELD WASHER FLUID Windshield washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely .
Y our vehicle was factory-filled with a 50/50 engine coolant and water concentration. If the concentration of coolant falls below 40% or above 60%, the engine parts could become damaged or not work properly . A 50–50 mixture of coolant and water provides the following: • Freeze protection down to -36° C (-34° F).
Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water . Add the mixture to the coolant reservoir , when the engine is cool , until the appropriate fill level is obtained. Do not add engine coolant when the engine is hot.
• Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing. • Do not add extra inhibitors or additives to the coolant.
Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle. If necessary , add enough 50/50 concentration of engine coolant and distilled water to bring the liquid level to the proper level.
less than 40%, the corrosion protection to your engine and cooling components may be compromised and permanent damage may result. What you should know about fail-safe cooling (4.6L V8 engine only) If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred.
2. Arrange for the vehicle to be taken to a service facility . 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low . Never remove the coolant reservoir cap while the engine is running or hot.
2. While the engine idles, turn the steering wheel left and right several times. 3. T urn the engine off. 4. Check the fluid level in the reservoir . 5. The fluid level should be between the MIN and MAX lines. Do not add fluid if the level is in this range.
Checking and adding manual transmission fluid (if equipped) 1. Make sure the vehicle is on a level surface or level hoist. 2. Clean the filler plug or dirt and debris. 3. Remove the filler plug and inspect the fluid level. 4. Fluid level should be at bottom of the opening.
CHECKING AND ADDING TRANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications.
BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules.
When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners.
If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal.
INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called T ire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.
Tire rotation Because your vehicle’ s tires perform different jobs, they often wear differently . T o make sure your tires wear evenly and last longer , rotate them as indicated in the scheduled maintenance guide. If you notice that the tires wear unevenly , have them checked.
Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity .
pressure readings to the receiver module located in the vehicle. The receiver module then transmits the status to the message center . For more tire warning information, refer to the Message Center in the Driver controls chapter . This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada.
accessory and recommends use of these or SAE class “S”. See your dealer or qualified service technician for more information on tire cables for your vehicle. Follow these guidelines when using snow tires and traction devices: • Cables or chains should only be used on the rear wheels.
Fuel ethanol and gasoline may contain benzene, which is a cancer -causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling.
Pure ethanol is the alcohol which is the intoxicating agent in liquor , beer and wine. It is distilled from the fermentation of plants such as field corn and sugar cane. When ethanol is used in the making of motor fuels, a small amount of a bad tasting chemical is added to discourage beverage use.
• Keep the fuel pump nozzle in contact with the fuel container while filling. • DO NOT use a device that would hold the fuel pump handle in the fill position. Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle.
Fuel quality Many of the world’ s automakers issued the W orld-wide Fuel Charter that recommends gasoline specifications to provide improved performance and emission control system protection for your vehicle. Gasolines that meet the W orld-wide Fuel Charter should be used when available.
Cleaner air Ford endorses the use of reformulated “cleaner -burning” gasolines to improve air quality . Running out of fuel A void running out of fuel because this situation may have an adverse affect on powertrain components.
If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury . Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician.
For consistent results when filling the fuel tank: • T urn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled.
Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy . Habits • Smooth, moderate operation can yield up to 10% savings in fuel.
• Carrying unnecessary weight may reduce fuel economy (approximately 0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy .
• Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in your scheduled maintenance guide performed according to the specified schedule.
If the vehicle’ s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition.
Replacing headlamp bulbs The high beam and low beam bulbs are located in the headlamp assembly . Follow the same steps to replace either bulb: T o remove the headlamp bulb: 1.
1. Install the new bulb in lamp assembly by pushing straight in and turning to lock in position. Y ou may need to turn the bulb slightly to align the grooves in the plastic base with the tabs in the lamp assembly . 2. Connect the electrical connector to the bulb.
Replacing tail/brake/turn/backup lamp bulbs The tail/brake/turn/backup bulbs are located in the tail lamp assembly , one just below the other . Follow the same steps to replace either bulb: 1. Make sure headlamp switch is in OFF position, then open the liftgate to expose the lamp assembly screws.
Replacing license plate lamp bulbs 1. Make sure headlamp switch is in OFF position, then remove two screws and the license plate lamp assembly from the liftgate. 2. Rotate bulb socket counterclockwise and remove from lamp assembly . 3. Carefully pull the bulb from the socket and push in the new bulb.
USING THE RIGHT BULBS Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “D.O.T .” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility .
V ERTICAL AIM ADJUSTMENT 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet) from a vertical wall or screen directly in front of it. • (1) Eight feet • (2) Center height of lamp to ground • (3) T wenty-five feet • (4) Horizontal reference line 2.
CLEANING AND CARING FOR YOUR VEHICLE Refer to the Accessories chapter for a list of Ford-approved cleaners, polishes and sealants. W ashing the exterior W ash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Detail W ash (ZC-3–A), which is available from your dealer .
Paint chips Y our dealer has touch-up paint and sprays to match your vehicle’ s color . T ake your color code (printed on a sticker in the driver’ s door jam) to your dealer to ensure you get the correct color .
• Cover the highlighted areas to prevent water damage when cleaning the engine. 4.6L V8 Engine 4.0L SOHC V6 Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage.
Plastic (non-painted) exterior parts Use only approved products to clean plastic parts. These products are available from your dealer . • For routine cleaning, use Detail W ash (ZC-3–A). • If tar or grease spots are present, use Ford Extra Strength T ar and Road Oil Removal (B7A-19520–AA).
Wood-tone trim • Clean the area with a damp cloth, then dry by wiping with a dry , soft, clean cloth. • Do not use household or glass cleaners as these may damage the finish. Interior For fabric, carpets, cloth seats and safety belts: • Remove dust and loose dirt with a vacuum cleaner .
Ford, Lincoln and Mercury car care products Y our Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
MOTORCRAFT PART NUMBERS Component 4.0L SOHC V6 engine 4.6L V8 engine Air filter element F A-1695 F A-1695 Fuel filter FG-986B FG-986B Battery BXT -65-650 BXT -65-650 Oil filter FL-820S FL-820S PCV val.
Fluid Ford Part Name Application Capacity Power steering fluid Motorcraft MERCON t AT F All Fill between the MIN and MAX lines on reservoir T ransmission fluid 1 Motorcraft MERCON t AT F 5-speed manual 2.4L (5.1 pints) 2 Motorcraft MERCON t V AT F Automatic transmissions only .
Fluid Ford Part Name Application Capacity Rear axle lubricant 5 Motorcraft SAE 75W -140 High Performance Synthetic Rear Axle Lubricant Conventional Axle 1.7L (3.5 pints) Limited slip axle 6 1.5L (3.25 pints) W indshield washer fluid Motorcraft Premium W indshield W asher Concentrate All 4.
LUBRICANT SPECIFICATIONS Item Ford Part Name or equivalent Ford Part Number Ford Specification Body hinges, latches, door striker plates and rotors, seat tracks, fuel filler door hinge and spring, hoo.
Item Ford Part Name or equivalent Ford Part Number Ford Specification Automatic transmission 1 Motorcraft MERCON t V AT F XT -5-QM MERCON t V Power steering fluid Motorcraft MERCON t Multi-Purpose AT .
2 Limited slip differentials must add 118 ml (4 oz) of Additive Friction Modifier XL—3 or equivalent meeting Ford specification EST -M2C118–A to the rear axle whenever the axle has been serviced.
1 4 2 5 3 Capacities and specifications 310.
IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’ s side.
1. W orld manufacturer identifier 2. Brake type and gross vehicle weight rating (GVWR) 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6.
Ford Extended Service Plan Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.
If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership.
In the United States: Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P .O. Box 6248 Dearborn, Michigan 48121 1-800-521-4140 (TDD for the hearing impaired: 1-800-232-5952) www .ford.com In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .
THE DISPUTE SETTLEMENT BOARD (U.S. only) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states.
Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm.
Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made.
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have be.
FORD MOTOR COMP ANY WORLDWIDE DIRECT MARKET OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. T elephone: (313) 594-4857 F AX: (313) 390-0804 If you are in another foreign country , contact the nearest Ford dealership.
V ehicle Security Styled wheel locks V ehicle security systems Comfort and convenience Cargo net Cargo organizers Cargo shade Cargo tray Engine block heaters T ire step T ravel equipment Ash cup Autom.
Remote start system Removable luggage rack adapters (bike and ski) Running boards/bars Seatback storage Scuff plates Smoker’ s package Soft luggage cover T rack rider bars (for luggage rack) T raile.
For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your veh.
Obtaining a French owner ’ s guide French Owner’ s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P .O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3. IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
A ABS (see Brakes) ..................... 187 Accessory delay ........................ 109 Air bag supplemental restraint system ................................ 163, 168 and child safety seats ............ 165 description ......................163, 168 disposal .
Changing a tire .........................237 Child safety restraints .............. 172 child safety belts .................... 172 Child safety seats ......................174 attaching with tether straps .. 179 in front seat ........................
Emergencies, roadside jump-starting .......................... 244 Emission control system .......... 289 Engine ........................................ 309 check engine/service engine soon light .................................... 8 cleaning ......
tachometer ................................ 16 trip odometer ............................ 16 GA WR (Gross Axle W eight Rating) ....................................... 214 calculating ............................... 216 definition .....................
interior lamps ......................... 102 replacing bulbs ...............291–295 Lane change indicator (see T urn signal) ........................91 Liftgate ..............................114, 118 Lights, warning and indicator ...... 8 AdvanceT rac .
fluid, refill capacity ................304 fluid, specifications ......... 307, 309 Power W indows ......................... 108 Preparing to drive your vehicle ........................................ 193 R Radio ................................ 55, 67, 76 Radio reception .
changing .................. 237–238, 240 checking the pressure ............ 276 replacing .................. 239–240, 278 rotating .................................... 277 snow tires and chains ............ 279 tire grades ........................
333.
334.
335.
Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity 85.2L (22.5 gallons) 4.0L Engine oil capacity (includes filter change) 4.7L (5.0 quarts). Use Motorcraft SAE 5W -30 Super Premium Motor Oil, Ford specification WSS-M2C153-G.
An important point after buying a device Ford 2002 Explorer (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ford 2002 Explorer yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ford 2002 Explorer - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ford 2002 Explorer you will learn all the available features of the product, as well as information on its operation. The information that you get Ford 2002 Explorer will certainly help you make a decision on the purchase.
If you already are a holder of Ford 2002 Explorer, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ford 2002 Explorer.
However, one of the most important roles played by the user manual is to help in solving problems with Ford 2002 Explorer. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ford 2002 Explorer along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
