Instruction/ maintenance manual of the product 1998 Expedition Ford
Go to page of 216
Before driving Introduction 2 Instrumentation 4 Controls and features 17 Seating and safety restraints 77 Starting and driving Starting 104 Driving 109 Roadside emergencies 131 Servicing Maintenance and care 151 Capacities and specifications 193 Customer assistance 201 Reporting safety defects 214 Index 215 All rights reserved.
ICONS Indicates a safety alert. Read the following section on W arnings. Indicates vehicle information related to recycling and other environmental concerns will follow . Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment.
SPECIAL NOTICES Using your vehicle as a snowplow Do not use this vehicle for snowplowing. Using your vehicle as an ambulance Do not use this vehicle as an ambulance.
P ON OFF RES SET ACCEL COAST D L H L H E F C H BRAKE FUEL RESET DOOR AJAR SELECT/RESET THEFT 0 MPH RPMX1000 km/h 20 40 60 80 00 20 40 60 PEDALS Headlamp control (pg. 17) T urn signal and wiper/washer control (pg. 53) Rear window defroster control (pg.
VOL-PUSH ON AM FM BASS TREB BAL FADE AUTO SET SEEK TUNE DISCS SCAN EJ TAPE CD DOLBY 8 NR REW 1 FF 2 SIDE 1-2 3 4 COMP 5 SHUFFLE 6 ST FM 1 4H A4WD 4L HI LO COOL WARM OFF P ANEL FLOOR DEF FLR & DEF P ANEL & FLOOR A/C MAX A/C Electronic sound system (pg.
W ARNING LIGHTS AND CHIMES Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge. The light comes on when there is approximately 1/16th of a tank indicated on the fuel gauge (refer to Fuel Gauge in this chapter for more information).
What you should do if the Service Engine Soon light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. T emporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1. The vehicle has run out of fuel.
Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter . Brake system warning Momentarily illuminates when the ignition is turned to the ON position, the engine is off and the parking brake is engaged.
High beams Illuminates when the high beam headlamps are turned on. SecuriLock Y anti-theft system This light indicates the anti-theft alarm system is armed. Momentarily illuminates when the ignition is turned to ON/ST ART . If the light fails to illuminate, continues to flash or remains on, have the system serviced.
Four wheel drive low (if equipped) This light momentarily illuminates when the ignition is turned to ON. Illuminates when four -wheel drive low is engaged. If the light continues to flash have the system serviced. Four wheel drive indicator (if equipped) This light momentarily illuminates when the ignition is turned to ON.
Fuel reset Illuminates when the ignition is turned to the ON position and the fuel pump shut-off switch has been triggered. For more information, refer to Fuel pump shut-off switch in the Roadside emergencies chapter . Safety belt warning chime Chimes to remind you to fasten your safety belts.
Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled. When the gauge first indicates empty , there is a small amount of reserve fuel in the tank.
Never remove the coolant reservoir cap while the engine is running or hot. This gauge indicates the temperature of the engine coolant, not the coolant level.
Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’ s electrical system checked as soon as possible. Engine oil pressure gauge This shows the engine oil pressure in the system.
Selectable features English/metric display Press this control to change the trip computer display from metric to English units. Press again to change from English to metric units. Mode control Each press of the MODE control will display a different feature as follows: Compass display .
A verage fuel economy . The display will indicate the vehicle’ s average fuel economy in liters/100 km (or miles/gallon) since last reset. • T o reset the average fuel economy: 1. Press the MODE control repeatedly until A VG F/ECON is displayed (no other display is resettable).
HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps.
P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim.
Never adjust the accelerator and brake pedal with feet on pedals or while the vehicle is moving. REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog.
USING YOUR AUDIO SYSTEM Premium AM/FM Stereo/Cassette/Premium Sound (CD Changer Compatible) MACH T Audio System with Premium AM/FM Stereo/ Cassette (CD Changer Compatible) SCAN VOL PUSH ON REW 1 FF 2 SIDE 1 . 2 3 4 COMP 5 SHUFF 6 AUTO TUNE SEEK SEL BAL FADE MUTE FM AM EJ BASS TREB CD TAPE RDS SCAN VOL PUSH ON REW 1 FF 2 SIDE 1 .
Y our vehicle is equipped with a delayed accessory feature. This feature enables the audio playing media to continue playing up to 10 minutes after the ignition has been turned off, or until a door is opened. V olume/power control Press the control to turn the audio system on or off.
• to increase volume compensation • to decrease or shut off the volume compensation AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped). AM/FM select in radio mode This control allows you to select AM or FM frequency bands.
• Press to select the next disc in the CD changer . Hold the control to fast-forward through the remaining discs. Seek function The seek function control works in radio, tape or CD mode (if equipped). Seek function in radio mode • Press to find the next listenable station down the frequency band.
Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’ s first side, direction automatically reverses to the opposite side of the tape.
If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. T o deactivate autoset and return to your audio system’ s manually set memory stations, press the control again.
T ape/CD select • T o begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the T APE control. Press the button during rewind or fast forward to stop the rewind or fast forward function. • T o begin CD play (if equipped with CD DJ), ensure that the CDs are loaded.
Eject function Press the control to stop and eject a tape. Dolby T noise reduction Dolby t noise reduction operates only in tape mode. Dolby t reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby t noise reduction.
The Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC) recommend FM radio broadcasters to use RDS technology to transmit information. FM radio stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired.
• Oldies • R&B • Religious • Rock • Soft • To p 4 0 Show • W ith RDS activated, press the RDS control until SHOW is displayed. • Use the SEL control to select TYPE, NAME or NONE. RDS clock feature Refer to Setting the clock for information.
Use the SEL control to select the desired signal mode (the selected mode will appear in the display). The following signal modes can be selected: • JAZZ CLUB—jazz club with clearly reflected sounds. • HALL—rectangular concert hall capacity of about 2 000 • CHURCH—church with a high vault.
Rear seat controls (if equipped) The rear seat controls allow the middle seat passengers to operate the radio, tape, CD or CD changer (if equipped). T o turn on the rear seat controls, press the memory preset controls 3 and 5 at the same time. The will appear in the display .
Turning the speakers on and of f Press to turn all speakers on or off. Using headphones Plug a 3.5 mm headphone (not included) into the jack. Press the speaker on/off control to operate the headphones. The rear speakers will cut out once the speaker on/off control is pressed.
Memory preset control Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2. Push the MEMORY control in CD changer mode (if equipped) to advance to the next disc. Seek function • In radio mode, press to find the next listenable station down the frequency band.
2. Press to eject the magazine. 3. T urn the magazine (A) over . 4. Using the disc holder release knob (C), pull the disc holder (B) out of the magazine. If you pull too hard on the disc holder , the disc holder may come completely out of the magazine.
5. Line up the CD with the groove of the disc holder . Ensure that the label on the CD faces downwards. 6. Press in on the disc holder until it locks securely into the magazine. If the disc holders are not fully locked into the magazine, the unit will not operate.
• The player’ s internal temperature is above 60°C (140°F). Allow the player to cool down before operating. • A disc with format and dimensions not within industry standards is inserted. Cleaning compact discs Inspect all discs for contamination before playing.
Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.
CLIMATE CONTROL SYSTEM Manual heating and air conditioning system Fan speed control Controls the volume of air circulated in the vehicle. T emperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
• MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster . Airflow will be from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle.
Operating tips • In humid weather , select DEF before driving. This will prevent your windshield from fogging. After a few minutes, select any desired position. • T o prevent humidity buildup inside the vehicle, don’ t drive with the climate control system in the OFF position.
Turning the EA TC on Press AUTOMA TIC, any of the override controls or the fan speed control. The EA TC will only operate when the ignition is in the ON position. Turning the EA TC off Press OFF . The Outside T emperature function will continue to operate until the ignition is turned off.
T emperature selection The display window indicates the selected temperature, function (AUTO or one of the override controls) and manual control of fan speed ( ) if automatic fan speed is not desired. T o control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons.
Fan speed ( ) When AUTOMA TIC is pressed, fan speed is adjusted automatically for existing conditions. Y ou can override fan speed at any time. T o control fan speed manually , use the thumbwheel or steering wheel control to cancel automatic fan speed operation.
• MAX A/C-Uses recirculated air to cool the vehicle. The temperature will display 16°C (60°F). T o exit, press AUTOMA TIC or any other override controls. MAX A/C is noisier than normal A/C but more economical and will cool the inside of the vehicle faster .
Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again. If the selected temperature is changed while the out.
• Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield). • If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
In order for the auxiliary A/C-heater controls to function, the driver’ s auxiliary A/C-heater control must be set to REAR. The instrument panel climate controls must be on in order for the auxiliary A/C-heater to operate.
• Anywhere between P ANEL and FLOOR to vary airflow between the outlets. POSITIONS OF THE IGNITION 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal.
SPEED CONTROL T o turn speed control on • Press ON. V ehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery , or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on.
T o set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
Y ou can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. T o set a lower set speed • Press and hold CST/COAST . Release the control when the desired speed is reached or • Press and release CST/COAST .
T o disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. T o return to a previously set speed • Press RES/RSM/RESUME.
TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control.
Push the control on the end of the stalk to activate washer . Push and hold for a longer wash cycle. The washer will automatically shut off after ten seconds of continuous use. Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position.
FLASH TO PASS Pull toward you to activate and release to deactivate. OVERDRIVE CONTROL Activating overdrive (Overdrive) is the normal drive position for the best fuel economy . The overdrive function allows automatic upshifts to second, third and fourth gear .
Forward storage bin (if equipped) Press the release control to open the storage compartment. The door will open slightly and can be moved to full open.
One-touch moon roof (if equipped) • Press and release the rear portion of the moon roof control to open. • Press and hold (as desired) the front portion of the moon roof control to close. • T o halt motion at any point during one-touch opening, press the control a second time.
Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Locate the compass module mounted at the base of the mirror .
Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut.
POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open. One touch down • Press AUTO completely down and release quickly .
Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls except for the driver’ s press the left side of the control.
POWER SIDE VIEW MIRRORS The ignition must be in ACC or ON position to adjust the power side view mirrors. T o adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror . 2. Move the control in the direction you wish to tilt the mirror .
Signal mirrors (if equipped) If your vehicle is equipped with signal mirrors, the word “signal” is located at the top of the right and left side view mirrors. When the turn signal is activated, the appropriate mirror will show a blinking red arrow .
Rear center console features (if equipped) The rear center console incorporates the following features: • utility compartment • cupholders POSITIVE RETENTION FLOOR MA T (IF EQUIPPED) Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in.
Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle.
Theft indicator The theft indicator on top of the instrument panel will operate as follows: • When the ignition is OFF , the theft indicator will flash briefly every 2 seconds to indicate the SecuriLock y system is protecting your vehicle.
3. W ithin five seconds of turning the ignition to OFF , insert the second previously programmed SecuriLock y key into the ignition and turn the ignition from OFF to RUN (maintain ignition in RUN for at least one second but no more than 5 seconds). 4.
Unlocking the doors Press this control to unlock the driver door . The interior lamps and running board lamps (if equipped) will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors or the driver’ s door .
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment.
Replacing lost transmitters If a remote transmitter has been lost or you would like to purchase additional transmitters for your vehicle (up to four may be programmed), take all your vehicle’ s transmitters to your dealer for reprogramming.
Deactivating/activating the autolock feature Before following the procedure, make sure that the ignition is OFF and all vehicle doors and the liftgate window are closed. Y ou must complete steps 1-7 within 30 seconds or the procedure will have to be repeated.
Programming your own personal entry code T o program your own code: 1. Enter factory set code (keypad will illuminate when pressed). 2. Press 1/2 control within five seconds of step 1. 3. Enter your personal 5 digit code. Enter each digit within five seconds of previous one.
Unlocking the doors with the keyless entry system T o unlock the driver door , enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit).
SEA TING Adjustable head restraints (if equipped) Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision.
Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Lift handle to move seat forward or backward. Pull lever up to adjust seatback. 60/40 split bench seat (if equipped) • Lift the release bar to move the seat forward or backward.
Using the armrest (if equipped) Push the release control to move the armrest up or down. Adjusting the front power seat (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Heated seats (if equipped) T o operate the heated seats: • Push control to activate. • Push again to deactivate. The indicator light will illuminate when activated.
Push or pull the head rests to the desired position. Rear folding bench seat (if equipped) Folding down the rear seats Ensure that the headrest is in the down position and no objects such as books, purses or briefcases are on the floor in front of the second row seats before folding them down.
Returning the seat to upright Always latch the vehicle seat to the floor , whether the seat is occupied or empty . If not latched, the seat may cause injury during a sudden stop. 1. Rotate the closeout panel onto the seatback and press the black control (adjacent to the green control) to lock.
Third row seat The third row seat is equipped with combination lap and shoulder belts in the outboard seating positions and a manual adjust tongue lap belt in the center seating position. For information on the proper operation of the safety restraints, refer to Safety Restraints in this chapter .
Removing the third row seat From the rear of the vehicle, with the liftgate open: 1. Disengage the lap/shoulder belt from the floor by inserting a key or small screwdriver through the hole in the boot of the detachable anchor . Then, press the release button to separate the detachable anchor from the anchor tongue.
• Pull the seat release lever located on the lower right side of the seatback while pushing the seatback down into the seat cushion. • The seatback will latch onto the cushion. 4. Lift the seat release bar located at the center of the seat near the floor to release the floor latches.
• When the rear of the seat is 10–13 cm (4–5 in) above the rear pins, let the seat drop. This will ensure that the seat will properly latch into the floor .
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front and rear seat passenger outboard safety belts have two types of locking modes described b.
• Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Shorten and fasten the belt when not in use. Front and second row safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver , front passenger and second row passengers. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder .
Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position.
AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
Steps you can take to properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably . • Recline the seat slightly (one or two degrees) from the upright position. Do not put anything on or over the air bag module.
How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation.
Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag is deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children.
Do not leave children, unreliable adults, or pets unattended in your vehicle. T o improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards.
When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter . • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch.
Installing child safety seats in combination lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. An air bag can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back.
3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat.
T ether anchorage hardware A tethered seat can be installed in the front passenger seat. Put the tether strap over the seatback and attach it to an anchor bracket. Anchor brackets can be bolted to the rear edge of the front passenger seat cushion. The bolt holes are in the bottom of the rear edge of the front passenger seat cushion frame.
PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. 4. Make sure the gearshift is in P (Park). 5. T urn the key to 4 (ON) without turning the key to 5 (ST ART).
Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light may not illuminate. ST ARTING THE ENGINE 1. T urn the key to 5 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts.
Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater -defroster system to respond quickly . Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below .
Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air . Improve vehicle ventilation by keeping all air inlet vents clear of snow , leaves and other debris.
BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system.
ABS warning lamp The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on and the engine is off. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced.
Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released.
Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy . STEERING Y our vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle.
Speed sensitive steering The steering in your vehicle is speed sensitive. At high speeds, steering assist will decrease to improve steering feel. At lower speeds, maneuverability will be increased.
The air suspension shut-off switch is located behind an access panel underneath the passenger side instrument panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driver .
T o avoid injury , never run the engine with one wheel off the ground, such as when changing a tire. T RANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift from being moved from P (Park) unless the brake pedal is depressed.
If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your dealer or a qualified service technician. Driving with a 4–speed automatic transmission Understanding gearshift positions Pull the gearshift lever towards you and downward to move the automatic gearshift.
N (Neutral) W ith the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear . (Overdrive) The normal driving position for the best fuel economy . T ransmission operates in gears one through four .
2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive).
CONTROL-T RAC AUTOMATIC FOUR-WHEEL DRIVE SYSTEM (IF EQUIPPED) Y our 4x4 features the heavy-duty Control-T rac system which includes a computer -operated transfer case. This unique system is interactive with the road, continually monitoring and adjusting torque delivery to the front and rear wheels to optimize vehicle control.
Using the Control-T rac system Shifting from A4WD to 4H Move the 4WD control from A4WD to 4H at any forward speed up to 88 km/h (55 mph). At temperatures below 0°C (32°F), shifts from A4WD to 4H should not be performed above 72 km/h (45 mph). Shifting from 4H to 4L (and 4L to 4H) 1.
Driving off-road with 4WD Y our vehicle is specially equipped for driving on sand, snow , mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain.
Once through water , always try the brakes. W et brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. After driving through mud, clean off residue stuck to rotating driveshafts, halfshafts and tires.
Driving on snow and ice A 4WD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. A void sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop.
• GVW (Gross V ehicle W eight) : Base curb weight plus payload weight. The GVW is not a limit or a specification. • GVWR (Gross V ehicle W eight Rating) : Maximum total weight of the base vehicle, passengers, optional equipment and cargo.
The Certification Label, found on the inside pillar of the driver’ s door , lists several important vehicle weight rating limitations. Before adding any additional equipment, refer to these limitations.
T RAILER TOWING T railer towing with your vehicle may require the use of a trailer tow option package. T railer towing puts additional loads on your vehicle’ s engine, transmission, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing.
T railer towing table (with heavy duty trailer tow option) GCWR (Gross Combined Weight Rating)/trailer weights Engine Rear axle ratio T ire size Maximum GCWR T railer weight range (0 - maximum) 4x2 4.6L 3.31 40.6 cm (16 in) 4 990 kg (11 000 lbs.) 0-2676 kg (0-5 900 lbs.
Preparing to tow Use the proper equipment for towing a trailer , and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance.
Safety chains Always connect the trailer’ s safety chains to the vehicle. T o connect the trailer’ s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer , follow the instructions that the rental agency gives to you.
Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer . Speed control may shut off if you are towing on long, steep grades. When towing a trailer: • Use a lower gear when towing up or down steep hills. This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling.
Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, • Do not allow the static water level to rise above the bottom edge of the rear bumper and • Do not allow waves to break higher than 15 cm (six inches) above the bottom edge of the rear bumper .
HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger , etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously .
The fuel pump shut-off switch is located in the passenger’ s foot well, behind the kick panel. FUSES AND RELA YS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse.
Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartridge Maxi Fuses Fuse Link Cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.
The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description 1 25A Audio 2 5A Overhead T rip Computer , Electronic Automatic T emperature Control (EA TC), Powertrain Control Module .
Fuse/Relay Location Fuse Amp Rating Description 7 5A Aux A/C Blower Relay , Console Blower 8 5A Radio, Remote Entry Module, GEM Module 9 — Not Used 10 — Not Used 11 30A Front W asher Pump Relay , .
Fuse/Relay Location Fuse Amp Rating Description 26 10A Right Side Low Beam Headlamp 27 5A Foglamp Relay and Foglamp Indicator 28 10A Left Side Low Beam Headlamp 29 5A Autolamp Module, T ransmission Ov.
If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Care chapter . The high-current fuses are coded as follows.
Fuse/Relay Location Fuse Amp Rating Description 12 10A* Rear Wipers 13 — Not Used 14 — Not Used 15 10A* Running Board Lamps 16 — Not Used 17 — Not Used 18 15A* Powertrain Control Module, Fuel .
Fuse/Relay Location Fuse Amp Rating Description 116 40A** Rear W indow Defroster , Heated Mirrors 117 — Not Used 118 — Not Used 201 — T railer T ow Park Lamp Relay 202 — Front Wiper Run/Park R.
CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Spare tire information Y our vehicle is equipped with a spare tire that may be used as a spare or a regular tire.
Removing the spare tire 1. Open the liftgate. 2. T wist counterclockwise and remove access plug (if equipped) from guide tube located just above the rear bumper . 3. Insert the straight end of the jack handle into the guide tube. Forward motion will stop and resistance to turning will be felt when properly engaged.
On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Refer to the instruction sheet (located behind the interior trim access panel with the jack) for detailed tire change instructions.
7. T urn OFF the air suspension switch (if equipped). 8. Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground.
• Front (4x4) • Rear T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the front or rear differential as a jacking point.
12. Remove the jack and fully tighten the lug nuts in the order shown. 13. Put flat tire, jack and lug wrench away . Make sure the jack is fastened so it does not rattle when you drive. 14. Unblock the wheels. 15. T urn on the air suspension switch (if equipped).
Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery .
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system.
Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for a further three minutes before disconnecting the jumper cables.
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a Scheduled Maintenance Guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service.
Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L V8 and 5.4L V8 engines 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Engine oil dipstick 5. Power steering fluid reservoir 6. Brake fluid reservoir 7. Power distribution box 8.
2. T urn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick).
Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter . 2. If the engine oil level is not within the MIN and MAX ranges, add only certified engine oil of the recommended viscosity . Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening.
BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the Scheduled Maintenance Guide for the service interval schedules: 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir .
WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low , add enough fluid to fill the reservoir . In very cold weather , do not fill the reservoir all the way .
If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become empty . If this occurs, add engine coolant to the reservoir . For more information on engine coolant maintenance, refer to Adding engine coolant in this chapter .
4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. Change your engine coolant according to the appropriate schedule listed in the Scheduled Maintenance Guide.
level in which you drive during winter months. Never increase the engine coolant concentration above 60%. Leave a 50/50 mixture of engine coolant and water in your vehicle year -round in non-extreme climates.
capable of completely shutting down automatically to prevent engine damage, therefore: 1. Pull off the road as soon as safely possible and turn off the engine. 2. Arrange for the vehicle to be taken to a service facility . 3. If this is not possible, wait a short period for the engine to cool.
4. Check the fluid level in the reservoir . It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low , add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines.
6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated area for normal operating temperature (H) or ambient temperature (C).
High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition.
BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules.
When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners.
• If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected.
2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the open end of the air filter housing. 4. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing.
Changing the wiper blades T o replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. T urn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.
T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). • Adjust tire pressure to recommended specifications found on the Certification Label.
Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity .
The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and chains. Follow these guidelines when using snow tires and chains: • Use only cable type chains offered by Ford as an accessory or equivalent.
Automotive fuels can cause serious injury or death if misused or mishandled. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling.
Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. Do not use gasolines containing methanol.
The American Automobile Manufacturers Association (AAMA) issued a fuel specification to provide information on high quality fuels that optimize the performance of your vehicle. W e recommend the use of fuels that meet the AAMA specification if they are available.
If you must replace the fuel filler cap, replace it with a genuine Ford or Motorcraft part. The customer warranty may be void for any damage to the fuel tank or fuel system if a genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure.
Capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty . Empty Reserve is the small amount of usable fuel remaining in the fuel tank after the fuel gauge indicates empty . The amount of Empty Reserve varies and should not be relied upon to increase driving range.
show how temperature impacts fuel economy . In general, lower temperatures give lower fuel economy . Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy .
• Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle Scheduled Maintenance Guide. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed.
EMISSION CONTROL SYSTEM Y our vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. T o make sure that the catalytic converter and other emission control components continue to work properly: • Use only unleaded fuel.
Please consult your “W arranty Guide” for complete emission warranty information. Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system.
Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance. Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’ s reach.
8. Insert the glass end of the new bulb into the headlamp assembly . When the grooves in the plastic base are aligned, push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly .
Replacing tail lamp/backup lamp bulbs The tail lamp/backup lamp bulbs are located in the same portion of the tail lamp assembly , one just below the other . Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies.
High-mount brakelamp T o change the high-mount brakelamp bulbs: 1. Remove the four screws from the high-mount brakelamp assembly . 2. Carefully pull the lamp assembly away from the vehicle to access the bulbs. 3. Remove the bulb socket by turning counterclockwise and a careful pull.
Using the right bulbs Function Number of bulbs T rade number Headlamps 2 9007 Front park/turn lamps 2 3157NAK Front sidemarker 2 194NA Foglamps 2 899 T urn/tail/brake lamps 2 3157K Liftgate lamp 2 916.
• Oncoming motorists frequently signal you to deactivate your high beams, and your high beams are not activated. • The headlamps do not seem to provide enough light for clear night vision. • The headlamp beams are pointed substantially away from a slightly down and to the right position.
A void getting wax on the windshield. If you have wax applied at a commercial car wash, it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield.
Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage.
Cleaning the wiper blades and windshield If the wiper blades do not wipe properly , clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent. T o avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents.
Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, wear or cuts.
Motorcraft part numbers Component 4.6L V8 engine 5.4L V8 engine Air filter element F A-1634 F A-1634 Battery BTX-65-650 BTX-65-650 Fuel filter FG-986B FG-986B Oil filter FL-820-S FL-820-S PCV valve EV -233 EV -233 Spark plugs* A WSF-32PP** A WSF-22E * Refer to V ehicle Emissions Control Information (VECI) decal for spark plug gap information.
REFILL CAPACITIES Fluid Ford Part Name Application Capacity Brake fluid High Performance DOT 3 Motor V ehicle Brake Fluid All Fill to line on reservoir Engine oil (includes filter change) Motorcraft 5W -30 Super Premium Motor Oil All 5.7L (6.0 quarts) Fuel tank N/A 4X2 with standard suspension 98.
Fluid Ford Part Name Application Capacity Engine coolant 3 Premium Engine Coolant 4.6L V8 engine with 1 row radiator 20.5 L (21.7 quarts) 4.6L V8 engine with 2 row radiator 21.8L (23.0 quarts) 5.4L V8 engine with 1 row radiator 22.6L (23.9 quarts) 5.4L V8 engine with 2 row radiator 24.
Fluid Ford Part Name Application Capacity Rear axle lubricant 4 Motorcraft SAE 75W140 Synthetic Rear Axle Lubricant All 2.9-3.1L (5.5-5.8 pints) W indshield washer fluid Ultra-Clear W indshield W asher Concentrate All 4.1L (4.5 quarts) 1 Ensure the correct automatic transmission fluid is used for a specific application.
LUBRICANT SPECIFICATIONS Item Ford part name Ford part number Ford specification Hinges, latches, striker plates and rotors, seat tracks, fuel filler door hinge and spring Multi-Purpose Grease DOAZ- 1.
Item Ford part name Ford part number Ford specification Automatic transmission (4R70W) Motorcraft MERCON t V AT F XT -5-QM WSS- M2C202-B Power steering fluid Premium Power Steering Fluid E6AZ- 19582-A.
ENGINE DATA Engine 4.6L V8 engine 5.4L V8 engine Cubic inches 281 330 Horsepower 215 @ 4500 rpm 235 @ 4250 rpm T orque 290 lb.-ft. @ 3250 rpm 325 lb.-ft. @ 3000 rpm Recommended fuel 87 octane 87 octane Firing order 1-3-7-2-6-5-4-8 1-3-7-2-6-5-4-8 Spark plug gap 1.
4 1 3 5 2 Capacities and specifications 197.
IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’ s side.
GETTING ROADSIDE ASSIST ANCE T o fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty .
Ford extended service plan Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.
Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to return to it for that service, but you may also take your vehicle to another Ford Motor Company dealership authorized for warranty repairs.
Please have the following information available when contacting Ford Customer Assistance: • Y our telephone number (home and business) • The name of the dealer and the city where the dealership is.
• sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle’ s performance as designed • a request for reimbursement of consequential .
T o properly review your case, the Board needs the following information: • legible copies of all documents and maintenance or repair orders relevant to the case • the year , make, model, and V eh.
T o Request a DSB Brochure/Application For a brochure/application, speak to your dealer or write/call to the Board at the following address/phone number: Dispute Settlement Board P .
If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMP ANY WORLDWIDE DIRECT MARKET OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.
Ford T riple Clean Ford Ultra-Clear Spray Glass Cleaner * May be sold with the Motorcraft name A wide selection of accessories is available through your local authorized Ford, Lincoln-Mercury or Ford of Canada dealer .
T ravel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adaptors Fog lights Framed luggage covers Heavy-duty battery Neutral towing transfer case kit (Explorer 4.
Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers (full and mini) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rall.
theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician.
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
Accessory delay ..........................61 Air bag supplemental restraint system .......................................... 89 and child safety seats .............. 90 description ................................ 89 disposal ........................
Engine oil checking and adding .............. 152 dipstick .................................... 150 specifications ...................150,152 Exhaust fumes .......................... 103 Fail safe cooling ........................ 157 Floor mats ......
fuel reset ...................................11 low fuel ........................................ 6 low washer fluid .......................10 safety belt ...................................8 service engine soon ................. 6,7 turn signal indicator .
V entilating your vehicle ........... 104 W arning chimes ........................... 11 W asher fluid .............................. 154 W ater , Driving through ............. 119 W indows ............................59,60,61 rear wiper/washer ......
Item Information Recommended fuel Unleaded fuel only - 87 octane Fuel tank capacity-4x2 without air suspension 98.6L (26.0 gallons) Fuel tank capacity-4x4 vehicles and 4x2 vehicles with rear load level suspension 113.6L (30.0 gallons) Engine oil (includes filter change) 5.
An important point after buying a device Ford 1998 Expedition (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ford 1998 Expedition yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ford 1998 Expedition - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ford 1998 Expedition you will learn all the available features of the product, as well as information on its operation. The information that you get Ford 1998 Expedition will certainly help you make a decision on the purchase.
If you already are a holder of Ford 1998 Expedition, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ford 1998 Expedition.
However, one of the most important roles played by the user manual is to help in solving problems with Ford 1998 Expedition. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ford 1998 Expedition along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
