Instruction/ maintenance manual of the product 1595 Ford
Go to page of 33
12 1595Ford Fiesta Remake Fuses - pre-1992 models Main fuse board: No Rating (amps) Circuit(s) protected 1 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electronic engine control system 2 15 . . . .
Additional fuses behind main fuse board: No Rating (amps) Circuit(s) protected 23 - . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unused 24/25 10 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bulbs Wattage Headlight (halogen) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H4, 60/55 Sidelight (front) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Direction indicators (main) .
wiring diagrams are included at the end of this manual. 2 Before attempting to diagnose an electrical fault, first study the appropriate wiring diagram, to obtain a complete understanding of the components included in the particular circuit concerned.
the inside face of the cover to remove and fit the fuses (see illustrations) . 2 To remove a fuse, use the tweezers provided to pull it out of the holder. Slide the fuse sideways from the tweezers. The wire within the fuse is clearly visible, and it will be broken if the fuse is blown.
windows (early models) and the tailgate remote release mechanism, where fitted. 19 Disconnect the battery negative (earth) lead (refer to Chapter 5A, Section 1). 20 To remove a switch, carefully prise it from its location using a thin flat-bladed screwdriver, then disconnect the multi-plug (see illustrations) .
50 Undo the two screws securing the contact switch and withdraw it from its tailgate location. 51 Unclip and disconnect the switch multi- plug, and disconnect the earth wiring. Remove the switch. 52 Refit in the reverse order of removal. Make sure that the pins and their contacts are clean.
the bulbholder together and remove it (see illustrations) . 22 All bulbs are of bayonet type fitting. 23 Refitting is a reversal of the removal procedure. Rear light cluster (Courier models) 24 Working inside the load compartment, unscrew the two black plastic nuts securing the light cluster assembly.
that the bulb and bulbholder cannot be separated - they are replaced as an assembly. 9 Refitting is a reversal of the removal procedure. Cigarette lighter illumination 10 Remove the cigarette lighter, as described in Section 12. 11 Pull the bulbholder from its location in the illuminated surround, then pull the bulb out of the bulbholder.
8 Refitting is a reversal of the removal procedure. Front direction indicator side repeater 9 Remove the appropriate front wheel arch liner as described in Chapter 11. 10 Remove the appropriate sill scuff plate as described in Chapter 11, and release the clip securing the insulation to the panel forward of the lower A-pillar.
work should therefore be carried out by a Ford dealer or service station with the necessary facilities. 2 Temporary adjustment can be made when the headlight has been removed and refitted, or to compensate for normal adjustment whenever a heavy load is being carried.
retaining tags, taking care to avoid damaging or losing the warning light graphic strips (see illustration) . 8 Remove its two Torx-head retaining screws, then detach and withdraw the speedometer from the front of the assembly. Tachometer 9 Carry out the procedure given in paragraphs 6 and 7.
16 Windscreen wiper motor and linkage - removal and refitting 2 Removal Wiper motor 1 Operate the wiper motor, then switch it off so that it returns to its rest position. 2 Disconnect the battery negative (earth) lead (refer to Chapter 5A, Section 1).
2 Carry out the procedure detailed in Sec- tion 16, paragraphs 2 to 6. 3 Remove the collars from the pivot shafts, unscrew the pivot shaft securing nuts and remove the washers and outer rubber bushes (see illustration) .
Windscreen washer jets and hoses 10 Disconnect the battery negative (earth) lead (refer to Chapter 5A, Section 1). 11 With the bonnet raised and supported on its stay, release the fasteners securing its insulation panel (where fitted). Remove the insulation panel.
illustration) . If possible, it is preferable to obtain purpose-made rods from an audio specialist, as these have cut-outs which snap firmly into the clips so that the radio can be pulled out.
27 Anti-theft systems - general information Anti-theft alarm system 1 This system provides an added form of vehicle security. When the system is activated, the alarm will sound if the vehicle is broken into through any one of the doors, the bonnet, or tailgate.
wiring passes through, as an aid to reassembly. Refitting 3 Position the clock spring on the steering wheel, routing the wiring as noted on removal, and secure with the retaining screws.
Wiring diagrams 12•19 Notes, internal connection details, and key to symbols 12 1595Ford Fiesta Remake.
12•20 Wiring diagrams Diagram 1: Starting, charging, cooling fan, ABS, warning lamps and gauges 1595Ford Fiesta Remake.
Wiring diagrams 12•21 Diagram 1a: Ignition system – carburettor models 12 1595Ford Fiesta Remake.
12•22 Wiring diagrams Diagram 1b: Ignition system – fuel-injected models 1595Ford Fiesta Remake.
Wiring diagrams 12•23 Diagram 1c: Typical 1.1/1.3/1.4 CFi fuel injection 12 1595Ford Fiesta Remake.
12•24 Wiring diagrams Diagram 1d: 1.6 EFi fuel injection (including RS Turbo) 1595Ford Fiesta Remake.
Wiring diagrams 12•25 Diagram 1e: DOHC 16-valve fuel injection 12 1595Ford Fiesta Remake.
12•26 Wiring diagrams Diagram 2: Exterior lighting – side and headlamps 1595Ford Fiesta Remake.
Wiring diagrams 12•27 Diagram 2a: Exterior lighting – stop, reversing, fog and direction indicator lamps 12 1595Ford Fiesta Remake.
12•28 Wiring diagrams Diagram 2b: Interior lighting, lights-on warning buzzer, clock and cigar lighter 1595Ford Fiesta Remake.
Wiring diagrams 12•29 Diagram 3: Ancillary circuits – horn (except XR2i/RS models), heater blower and heated front /rear screens 12 1595Ford Fiesta Remake.
12•30 Wiring diagrams Diagram 3a: Ancillary circuits – horn (R2i and RS models) and wash/wipe 1595Ford Fiesta Remake.
Wiring diagrams 12•31 Diagram 3b: Ancillary circuits – central locking, electric windows and tailgate release (up to 1992) 12 1595Ford Fiesta Remake.
12•32 Wiring diagrams Diagram 3c: Ancillary circuits – central locking, electric windows and tailgate release (1992-on) 1595Ford Fiesta Remake.
Wiring diagrams 12•33 Diagram 4: In-car entertainment 12 1595Ford Fiesta Remake.
An important point after buying a device Ford 1595 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ford 1595 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ford 1595 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ford 1595 you will learn all the available features of the product, as well as information on its operation. The information that you get Ford 1595 will certainly help you make a decision on the purchase.
If you already are a holder of Ford 1595, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ford 1595.
However, one of the most important roles played by the user manual is to help in solving problems with Ford 1595. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ford 1595 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
