Instruction/ maintenance manual of the product PN 643657 Fluke
Go to page of 16
Model 16 English In struction Sheet Page 1 ® 16 Multimeter with Temperat ure Instruction Sheet P Read First: Safety Information To ensure that the meter is used safely, follow these instruct i ons: • Do not use the meter if the meter or test l eads appear dam aged, or if you suspect t hat t he meter is not operat i ng properly.
Model 16 English In struction Sheet Page 2 Symbols Press button. Press button t o switc h between mod es. Double ins ulation. Manual rangi ng mod e. ip14i.eps Automatic Range Selection The meter defaults to autoranging when you turn it on. The 4000 mV range can be entered only with manual range selection.
Model 16 English In struction Sheet Page 3 AC and DC Voltage Also r efer to V • Check. Volts AC Volts DC Input Impedance ≅ 5 M Ω Input Impedance ≅ 10 M Ω 50 Hz to 400 Hz 16 MULTIMETER OFF V 600V COM CAT + AC / DC DC AC 4000 mV 4V 40V 400V 600V 16 MULTIMETER OFF V 600V COM CAT + AC / DC ip01i.
Model 16 English In struction Sheet Page 4 W V • Check If a dc or ac voltage greater than about 4.5V is pres ent across the i nputs when the meter is set to R , G , or e , the m eter switc hes automatically to dc or ac voltage mode (V • Chec k mode).
Model 16 English In struction Sheet Page 5 Temperature 80PK-1 Type K Thermocouple Probe Vent or Pipe ° C ° F 16 MULTIMETER OFF 600V COM CAT + A TEMPERATURE V • Check ip19f.eps Note correct connect or polarity. To meet stated accuracy , the 80AK temperature adapter must be at the same temperat ure as the meter.
Model 16 English In struction Sheet Page 6 Capacitance E Turn off circuit power; then disconnect and discharge the capacit or before measuring c apacitance. + If the capacitor requires more discharging, diSC is displayed while the capacitor discharges .
Model 16 English In struction Sheet Page 7 Microamps µ A Range 0 to 200 µ A 16 MULTIMETER OFF 600V COM CAT + A TEMPERATURE V • Check Flame sensor probe Control module µA AC µA DC ip20i.
Model 16 English In struction Sheet Page 8 Diode Test G Turn off circ uit power before testing . For best res ults diod es should be m easured out of circuit.
Model 16 English In struction Sheet Page 9 MIN MAX µ F (Records the lowest and highest measure ments) V • Check , autoranging, and B attery Saver are disabled. Put the meter in the proper range before entering MIN MAX. When the reading changes more than about 50 digits, the meter gives a short beep.
Model 16 English In struction Sheet Page 10 MIN MAX with Elapsed Time µ F Records the hours and minut es bet ween when MIN MAX was entered and the last high and low was recorded. OL is displayed for times longer than 99:59. To enable the MIN MAX timer, hold down M while turni ng the rot ary switch from OFF to either measurement mode.
Model 16 English In struction Sheet Page 11 Disabling the Be eper To disable the beeper for all modes, hold down r for 2 seconds while turning the meter on. Continuity Capture To set up the meter to capture intermit t ent shorts and opens, turn the switch to GR , connect the leads to the c ircuit; t hen press M .
Model 16 English In struction Sheet Page 12 Maintenanc e Clean the case wit h a damp cloth and detergent. Do not use abras ives or solven ts. Battery Replacement Remove the test l eads bef ore dis assem bling the case.
Model 16 English In struction Sheet Page 13 Speci fications Accuracy is speci fi ed f o r a period of one year after cali brati on, at 18 ° C to 28 ° C (64 ° F to 82 ° F) with relative humidity to 90%. AC conversi ons are ac-coupled, av erage responding, and calibrated to the rms value of a sine wave input.
Model 16 English In struction Sheet Page 14 Func tion Range Resoluti on Accur acy Burd en Vol tage (5 0 H z to 400 Hz) 0 to 200 µ A0 . 1 µ A ± (2% + 3 co unts) <5 mV/ µ A 0 to 200 µ A0 .
Model 16 English In struction Sheet Page 15 MIN MAX Recording with Elapsed Time Elapse d Ti m e Resolu ti on Accur ac y 0 to 100 h ours (99 :59) 1 minut e 0.
Model 16 English In struction Sheet Page 16 LIMITED WARRANT Y & LIMITATION OF LIABILITY Each Fluke product is warra nted to be free fr om defects in m aterial and workmans hip under normal use and s ervice. The w arran ty period is thr ee years and begins on the date of shipme nt.
An important point after buying a device Fluke PN 643657 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fluke PN 643657 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fluke PN 643657 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fluke PN 643657 you will learn all the available features of the product, as well as information on its operation. The information that you get Fluke PN 643657 will certainly help you make a decision on the purchase.
If you already are a holder of Fluke PN 643657, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fluke PN 643657.
However, one of the most important roles played by the user manual is to help in solving problems with Fluke PN 643657. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fluke PN 643657 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
