Instruction/ maintenance manual of the product 1060AM-NM-LRVAR Fluke
Go to page of 16
1060AM-NM-LRVAR Local, Remote, and Flasher Alarms Operators Manual March 2005 Manual No. 1060AMNMLRVAR-1 Rev. 1 © 2004, 2005 Fluke Corporat i on, All rights reserved .
Fluke Biomedical Radiation Management Services 6045 Cochran Road Cleveland, Ohio 44139 440.498.2564 www.flukebiomedical.com/rms.
i Table of Contents Section 1: Introductio n ................................................................................................ 1-1 1.1 Procedures, Warni ngs and Caut ions ........................................................... 1-1 Section 2: Instructions .
(Blank Page).
Introduction Procedures, Warnings and Cautions 1 1-1 Section 1 Introduction 1.1 Procedures, Warnings and Cautions • The equipment described in this manual is intended to be used for the detection and measurement of ionizing radiation.
1060AM-NM-LRVAR Operators Manual (Blank Page).
Instructions General Description 2 2-1 Section 2 Instructions 2.1 General Description Refer to 1060-005 drawing located in Appendix A . The Fluke Biomedical local , remote , and flas her alarms are used in conjunction with the Victoreen Model 1060AM-NM-LR.
1060AM-NM-LRVAR Operators Manual 2-2 Electrical Requirements 120 VAC 50/60 Hz 120 VAC 50/60 Hz 120 VAC 50/60hz 2.3 Receiving Inspection Upon receipt of the unit: 1. Inspect the carton(s) and contents for dam age. If damage is evident, file a claim with the carrier and notify Fluke Biomedical at 440.
Instructions Installation 2 2-3 2.5 Installation To prevent electrical shock, ensure that power is disco nnected before installing the alarms Installation of the 1060am-nm-lrvar consists of mounting the unit , providing an electrical interface , and performing an operational check.
1060AM-NM-LRVAR Operators Manual 2-4 2.6 Electrical interface The Local alarm (1060-024) requires power connections as follows: (See appendix A for the 1060-13 and 1060-024 drawings) Terminate the input power to TB2-1(L1) of the Local al arm assembly at the end of this installation .
Instructions Operation 2 2-5 2.7 Operation The red beacons and red leds are ON . The flasher alarm is blinking . Connect the free end of the I/O (1060ds- 24) cable to the model 1060AM-NM-LR I/O connector. Connect the 1060AM-NM-110 (12 volt 500 mA) power cube connector to the 1060AM- NM-LR power input .
1060AM-NM-LRVAR Operators Manual (Blank Page).
Maintenance Maintenance and Cleaning 3 3-1 Section 3 Maintenance and Cleaning To prevent injury, do not remove or insert lamp when unit is energized . To prevent damage to the lens, do not use abrasive materials or cle aners Refer the parts lists for the required type of lamp After disconnecti ng power, replace the lamp as follows: 1.
1060AM-NM-LRVAR Operators Manual 3-2 1. Slide the acrylic yellow panel out from either side of the chassis . To prevent property damage and injury, do not touch glass with bare fin gers. Grasp glass with a soft clean cloth or with packaging supplied with the replacement lamp.
Appendix Applicable Drawings and Parts List A A-1 Appendix A Applicable Drawings and Parts List 4.1 Applicable Drawings and Parts List 1060-005 Main Assembly 1060-005 Main Assembly Parts List 1060-010.
Fluke Biomedical Radiation Management Services 6045 Cochran Road Cleveland, Ohio 44139 440.498.2564 www.flukebiomedical.com/rms.
An important point after buying a device Fluke 1060AM-NM-LRVAR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fluke 1060AM-NM-LRVAR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fluke 1060AM-NM-LRVAR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fluke 1060AM-NM-LRVAR you will learn all the available features of the product, as well as information on its operation. The information that you get Fluke 1060AM-NM-LRVAR will certainly help you make a decision on the purchase.
If you already are a holder of Fluke 1060AM-NM-LRVAR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fluke 1060AM-NM-LRVAR.
However, one of the most important roles played by the user manual is to help in solving problems with Fluke 1060AM-NM-LRVAR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fluke 1060AM-NM-LRVAR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
