Instruction/ maintenance manual of the product 9500 Fisher
Go to page of 16
www.Fisher.com D100380X012 Type 9 500 B utterfly C ontrol V alve Contents Introduction 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scope of Manual 1 . . . . . . . . . . . . . . . . . . . . . . . . . Description 1 . . . . . . . . . .
9500 Valve Instruction Manual Form 2433 November 2007 2 Table 1. Specifications Valve Sizes NPS J 2, J 3, J 4, J 6, J 8, J 10, or J 12 Valve Body Style Flangeless (wafer-type) valve body to be installed between pipeline flanges End Connection Styles Flangeless (wafer-style) valve body mates with CL125 flat-face flanges per ASME B16.
9500 Valve Instruction Manual Form 2433 November 2007 3 that must be taken to protect against process media. If installing into an existing application, also refer to the WARNING at the beginning of the Maintenance section in this instruction manual.
9500 Valve Instruction Manual Form 2433 November 2007 4 Figure 2. Valve Shaft Marking A2755-1/IL LOCATION OF INDEX MARK ON END OF VALVE SHAFT TAIL OF Fishtail DISC LOCATION OF FLAT SPOT ON VALVE SHAFT.
9500 Valve Instruction Manual Form 2433 November 2007 5 result if the partial O-ring faces are not properly supported. Do not use flanges having an inside diameter larger than the maximum shown in table 3. The NPS 6 to 10 sizes must not be used with slip-on flanges unless flange adaptors are used to support the liner.
9500 Valve Instruction Manual Form 2433 November 2007 6 leakage downstream (between the bushings and disc hubs) may also indicate a need for hub seal adjustment. To adjust the hub seals: 1. Tighten both thrust-plate cap screws (key 10) 1/4 turn on one side (the side where shaft leakage is occurring).
9500 Valve Instruction Manual Form 2433 November 2007 7 Figure 5. Tandem Linkage Adjustment for Three-Way Valve Assemblies B2144-1 / IL locknuts on the tandem linkage when adjustment is complete. Maintenance Use table 4 to locate and correct possible leakage or mechanical linkage problems with the valve.
9500 Valve Instruction Manual Form 2433 November 2007 8 Table 4. Troubleshooting Guide Fault Possible Cause Correction 1. Leakage out sides of valve (at thrust plates) between thrust bushings and shaft. a. Hub seals require adjustment. b. Taper pins are not sealed.
9500 Valve Instruction Manual Form 2433 November 2007 9 Table 5. Taper Pin Details for 9500 Series Valves VALVE SIZE, NPS SHAFT DIAMETER mm (Inches) AMERICAN STANDARD TAPER PIN SIZE DRILL SIZE 2 3, 4 12.7 (1/2) 15.9 (5/8) 2 3 #20 (0.161 Inches) #16 (0.
9500 Valve Instruction Manual Form 2433 November 2007 10 b. If installing a new shaft, insert the new shaft into the valve body and disc. Measure between the valve body and the splined end of the shaft. Make certain that the distance is correct to engage the actuator coupling lever.
9500 Valve Instruction Manual Form 2433 November 2007 11 Figure 6. Splined-Shaft Index Mark Alignment for Standard Mounting Position-Valve Action Combinations 54A3246-B B1054-3*/IL 14A7222-A 54A3246-B.
9500 Valve Instruction Manual Form 2433 November 2007 12 1. Refer to the appropriate actuator instruction manual for assistance in disconnecting and removing the actuator lever. Avoid disturbing the actuator turnbuckle adjustment, if possible. 2. If the valve disc is a Fishtail disc, rotate the disc 180 degrees from the original position.
9500 Valve Instruction Manual Form 2433 November 2007 13 Parts List Note Part numbers are shown for recommended spares only. For part numbers not shown, contact your Emerson Process Management sales office.
9500 Valve Instruction Manual Form 2433 November 2007 14 Figure 7. Type 9500 Valve Body Assembly G34171-B/DOC Key Description Part Number 15* Taper Pin (2 req’d) (continued) S17400 (17-4 PH) NPS 2 F.
9500 Valve Instruction Manual Form 2433 November 2007 15.
9500 Valve Instruction Manual Form 2433 November 2007 16 Emerson Process Management Marshalltown, Iowa 50158 USA Cernay 68700 France Sao Paulo 05424 Brazil Singapore 128461 www.
An important point after buying a device Fisher 9500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fisher 9500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fisher 9500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fisher 9500 you will learn all the available features of the product, as well as information on its operation. The information that you get Fisher 9500 will certainly help you make a decision on the purchase.
If you already are a holder of Fisher 9500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fisher 9500.
However, one of the most important roles played by the user manual is to help in solving problems with Fisher 9500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fisher 9500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
