Instruction/ maintenance manual of the product V3 DS603 Fisher & Paykel
Go to page of 12
R INST ALLA TION INSTRUCTIONS (NOTE: FOR INTEGRA TED P ANEL PREPARA TION INSTRUCTIONS REFER TO SUPPLIED SHEET) part number 526607 N 05/2005 (page 1 of 12) US CA NO TE T O THE INST ALLER 1. R ead these instructions completely and carefully . 2. Installation of this DishDrawer ® requires basic mechanical and electrical skills.
BEFORE YOU ST ART - DOUBLE & SINGLE MODELS P ARTS SUPPLIED DOUBLE MODELS Drain Hose Support (1) Drain Hose Joiner (1) Wire Clips (2) Installation T abs (2) Phillips 16mm Screws (7) Prefinished T o.
DOUBLE MODELS SERVICES SPECIFICA TIONS TOE KICK DEPTH Prefinished & Flat Door 2”-4 3 / 8 ” (50-110mm) ; Integrated 5” (127mm) less the T oe Kick Panel thickness. Minimum P anel thickness using the supplied screws is 3 / 8 ” (9mm). # DOOR FRONT HEIGHT Prefinished & Flat Door 30 5 / 64 ” (764mm); Integrated 28 1 / 4 ” ( 717.
MAX height to top of AIR BREAK (countertop or wall-mounted) 37 3 / 8 ” (950mm) DOUBLE MODELS PLUMBING OPTIONS OPTION 1 DishDrawer® and Standpipe Ø1 1 / 2 ” (38mm) with Air Gap. OPTION 2 DishDrawer® with W aste Disposal. 29 1 / 2 ” - 34 3 / 4 ” (750mm - 882.
W A TER CONNECTION Recommended HO T (Maximum 140°F/60°C). Supplied hose to suit 3 / 8 ”(9mm) male compression fitting. W A TER SOFTENER MODELS Refer to your DishDrawer® User Guide for how to set up your water softener .
SINGLE MODELS OPTION 1 DishDrawer® and Standpipe Ø1 1 / 2 ” (38mm) with Air Gap. OPTION 2 DishDrawer® with W aste Disposal. MAX height to top of AIR BREAK (countertop or wall-mounted) 37 3 / 8 .
PLEASE NO TE : Y our model of DishDrawer® may differ from the model shown in the installation diagrams. Installation is similar for all models for either Single or Double models. Information referring to Single models only is highlighted in blue. Installation diagrams have been simplified to enable clearer instruction.
SINGLE MODELS ONL Y Check the position of the chassis is still where mark ed on the cavity , before securing the product. There are four 5 / 8 ” (16mm) round holes, two on the left and two on the right hand side in the sound insulation. These provide access to the mounting tabs.
R INST ALLA TION INSTRUCTIONS STEP 5: ELECTRICAL CONNECTION T o refit the tub, make sure both of the latches at the rear of each drawer runner are facing forward. Ensure hoses are hooping upward. Place the tub on the half open drawer runners and close the drawer .
Attach the Drain Hose Support to the cabinetry (with the screw supplied) to prevent siphoning and to keep the drain hose(s) from kinking. If required, the Drain Hose(s) may be trimmed to a suitable length. 29 1 / 2 ” - 34 3 / 4 ” (750mm - 882.5mm) 29 1 / 2 ” - 34 3 / 4 ” (750mm - 882.
On the chosen groove cut down the vertical ribs at the centre and the ends using a knife. Cut along full length with a knife. T urn T oe Kick over , bend and then cut from front.
R INST ALLA TION INSTRUCTIONS Be sure product is level, securely fastened to the cabinetry and opens and closes freely . The DishDrawer® must be free to close with no resistance from the cabinetry . Be sure the inlet hose to valve connection is tightened a further half turn after seal contact.
An important point after buying a device Fisher & Paykel V3 DS603 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fisher & Paykel V3 DS603 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fisher & Paykel V3 DS603 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fisher & Paykel V3 DS603 you will learn all the available features of the product, as well as information on its operation. The information that you get Fisher & Paykel V3 DS603 will certainly help you make a decision on the purchase.
If you already are a holder of Fisher & Paykel V3 DS603, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fisher & Paykel V3 DS603.
However, one of the most important roles played by the user manual is to help in solving problems with Fisher & Paykel V3 DS603. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fisher & Paykel V3 DS603 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
