Instruction/ maintenance manual of the product DD90SDFTM2 Fisher & Paykel
Go to page of 24
NZ A U GB IE 590202B 12. 11 DD90SDF(H)TX2, DD90SDFTM2 (Designer) & DD90S(H)TI2 (Integr ated) models INST ALLA TION INSTRUCTIONS DishDr aw er TM dishw asher.
2 FOLL O W THE INST ALLA TION SE QUENCE RELEV ANT T O Y OUR MODEL 1 DD90SDF(H)TX2 DD90SDFTM2 Designer PRODUCT & CABINETRY DIMENSIONS P ARTS SUPPLIED CA VITY PREP ARA TION MAXIMUM DIST ANCE OF HOSE.
3 ADDITIONAL SAFETY AND W ARNINGS - INTE GRA TED MODELS ONL Y 2b W ARNING! Cut hazar d T ake care - panel edges ar e sharp . F ailure to use caution could result in injury or cuts. IMPORT ANT SAFET Y INSTRUCTIONS! Read these instructions completely and carefully .
4 P ARTS SUPPLIED - ALL MODELS 3a If the Drain hose supplied is not long enough to reach your services, y ou must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hose by 3.6m. The kit is available from the nearest F isher & Payk el Authorised Ser vice Centre or thr ough our local website listed at the end of this document.
5 ADDITIONAL P ARTS SUPPLIED WITH INTE GRA TED MODELS 3b External V enting k it (1) supplied with Integrated models with remote (NZ A U) only Panel mounting screws (14) Panel bracket (1) (attached to .
6 4 PRODUCT DIMENSIONS A H I J K Side Plan G F B C D E Product dimensions (mm) Designer Integrated Remote control Integrated Badge control A overall height 1 of product (incl. fr ont panel height) 478 478 478 B overall width of product 895 min. 855 min.
7 5 CABINETR Y DIMENSIONS Plan Side LM P O N 18 mm 20 mm 2 mm O N Minimum clearances from adjac ent cabinetr y Cabinetry dimensions mm Designer Integrated Remote control Integrated Badge control L height of cavity (from support sur face to underside of benchtop) 480 480* 480* M inside height of cavity 460 min.
8 The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry: WID TH OF THE P ANEL Measure A ( the width between adjacent door/drawer fr onts) and write it in the rst box below , then complete the equation.
9 The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry: WID TH OF THE P ANEL Measure A ( the width between adjacent door/drawer fr onts) and write it in the rst box below , then complete the equation.
10 7a CA VITY PREP ARA TION W ater Connection Recommended COLD (Maximum 60°C ). ¾ “ BSP (GB20) t o suit flat washer . W ater Pressur e W ater softener models Max. 1 MPa (145 psi) Min. 0.1 MPa (14.5 psi) Models without water softener Max. 1 MPa (145 psi) Min.
11 7b 7c INTEGRA TED MODELS WITH REMO TE (NZ AU) ONL Y - PREP ARA TION FOR EXTERNAL VENTING THROUGH SAME CABINET INTEGRA TED MODELS WITH REMO TE (NZ AU) ONL Y - PREP ARA TION FOR EXTERNAL VENTING THROUGH ADJ A CENT CABINET ø 60 mm ø 60 mm max. 5 mm max.
12 8 MAXIMUM DIST ANCE OF HOSES & CORD FR OM CHASSIS EDGE Lef t h an d side Right han d side Drain hose - 2000 mm Inlet hose - 1650 mm Venting hose - 1265 mm Venting hose - 1925 mm (Integrated models only) (Integrated models only) Power cord (excl.
13.
14 REC OMMENDED METHOD (a) - SECURE WITHOUT DRA WER REMOV AL (FRAMELESS CABINETR Y ONL Y) 10a 9a A T T ACH SIDE MOUNTING BRA CKETS INTEGRA TED MODELS WITH REMO TE (NZ A U) ONL Y - A T T ACH VENTING HO.
15 12a 11a PULL THROUGH HOSE S & MO VE INTO THE CA VITY SE CURE THE DRA WER 1 3 2 Open the drawer halfway . Using a flat-bladed screwdriv er , prise the grey rubber plug out of the trim moulding. Replace the grey rubber plug back into the trim moulding and ensure the trim seal is facing forward.
16 10b 9b INTE GRA TED MODELS WITH REMOTE (NZ A U) ONL Y - A T T ACH VENTING HOSE PULL THROUGH HOSE S & MO VE INTO THE CA VITY F itted Elbow Check that the fitted elbow is rotated left or right (depending on the direction of the routing), then ensure the venting hose is securely attached to it.
17 11b 12b 13b 14b REMO VE THE DRA WER SE CURE THE DRA WER T O THE CABINETRY REFIT THE DRA WER ONT O THE RUNNERS INTE GRA TED MODELS WITH REMOTE (NZ A U) ONL Y - SE CURE THE EXTERNAL VENT 2 1 After routing the vent hose through and out the hole cutout, attach and secure the vent by tightening the f our screws pro vided.
18 INTE GRA TED MODELS WITH REMO TE (NZ A U) ONL Y - INST ALLING THE FRONT P ANEL 3 1 1 2 REMO VE BRACKET FR OM PRODUCT A T T A CH P ANEL T O P ANEL BRA CKET 15a 16a Impor tant! Use all 14 screws provided as shown.
19 INTE GRA TED MODELS WITH REMO TE (NZ A U) ONL Y - INST ALLING THE FRONT P ANEL 2 2 1 Impor tant! Ensure the rubber seal between the drawer and panel is kept in place. A T T A CH P ANEL T O PRODUCT EAR TH THE P ANEL When refitting the door pins, ensure they are orientated as shown.
20 INTE GRA TED MODELS WITH BADGE (GB IE) ONL Y - INS T ALLING THE FRONT P ANEL & BADGE C ONTROLS DETERMINE BADGE CUT OUT L OCA TION ROUTE B ADGE WIRING THROUGH P ANEL A T T A CH P ANEL T O P ANEL BRA CKET REMO VE BRACKET & DISC ONNECT B ADGE 15b 17b 18b 16b 1 3 4 1 2 1 2 Impor tant! Use all 14 screws provided as shown.
21 REA TT A CH BADGE & E ARTH THE P ANEL A T T A CH P ANEL T O PRODUCT 19b 20b W ARNING! 1 2 Electrical Shock Hazard Connect the integrated badge earth wire to one of the two tabs provided on the panel bracket. T o ear th the panel bracket, connect the earth wire from the product to the other tab.
22 ADJUS T P ANEL HEIGHT T O ALIGN THE CABINETRY GAPS Inser t an appropriately sized Philips scr ewdriver int o the hole above the door pin and r otate the panel up or down to align the gaps in y our cabinetry. Repeat on the other side if necessary. The panel has a maximum travel of 2 mm up or do wn.
23 THERE ARE TWO DIFFERENT PL UMBING AND DRAINA GE OPTIONS. CHOOSE WHICH IS MORE SUIT ABLE. 22 1 3 2 750-882.5 mm 1 2 38 mm max. 120 mm 750-882.5 mm ** 3 4 5 If space is limited for fixing, push hose .
24 26 25 FINAL CHE CKLIST TROUBLE SHOOTING Check all par ts are installed. Ensure product is level , securely fastened to the cabinetr y and opens and closes freely .
An important point after buying a device Fisher & Paykel DD90SDFTM2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fisher & Paykel DD90SDFTM2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fisher & Paykel DD90SDFTM2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fisher & Paykel DD90SDFTM2 you will learn all the available features of the product, as well as information on its operation. The information that you get Fisher & Paykel DD90SDFTM2 will certainly help you make a decision on the purchase.
If you already are a holder of Fisher & Paykel DD90SDFTM2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fisher & Paykel DD90SDFTM2.
However, one of the most important roles played by the user manual is to help in solving problems with Fisher & Paykel DD90SDFTM2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fisher & Paykel DD90SDFTM2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
