Instruction/ maintenance manual of the product DD60D 7 Fisher & Paykel
Go to page of 21
NZ A U GB IE 590200C 12. 11 DD60D 7 models INST ALLA TION INSTRUCTIONS DishDr aw er TM dish w asher.
2 FOLL OW THE INS T ALLA TION SE QUENCE RELEV ANT T O Y OUR MODEL 1 PRODUCT & CABINETR Y DIMENSIONS DD60DC(H)X7 DD60DC(H)W7 DD60DC(H)B7 DD60DCM7 P ARTS SUPPLIED CA VITY PREP ARA TION MAXIMUM DIST .
3 SAFETY AND W ARNINGS - ALL MODELS ADDITIONAL SAFETY AND W ARNINGS - INTEGRA TED MODELS ONL Y 2a 2b W ARNING! Electrical shock hazard Before installing the dish washer , remov e the house fuse or open the circuit breaker . This appliance must be earthed.
4 P ARTS SUPPLIED - ALL MODELS 3a If the Drain hoses supplied are not long enough to reach y our services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hoses b y 3.6 m. The kit is available from the nearest F isher & Paykel Authorised Service Centre or our loc al website listed at the end of this document.
5 ADDITIONAL P ARTS SUPPLIED WITH INTE GRA TED MODELS 3b Panel bracket (2) (attached to product ) Panel mounting screws (12) T oekick mounting screws (5) T oekick mounting bracket (1) (A custom toekic.
6 H K M N A O O I Side Plan G F J L B C E D 4 PRODUCT DIMENSIONS Product dimensions (mm) Classic Designer Integrated Remote control Integrated Badge controls A overall height 1 of product 820-880 2 820-880 2 820-880 2 820-880 2 B overall width of product 599 599 599 599 C overall depth of product (excl.
7 5 CABINETR Y DIMENSIONS Plan Side P Q R S T Minimum clearances from adjac ent cabinetry min. 13 mm clearance from a corner cupboard min. 2 mm clearance to adjacent cupboard door Cabinetry dimensions (mm) Classic Designer Integrated Remote control Integrated Badge controls P inside height of cavity* min.
8 The following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry . The nal panel/cabinetry alignment is achieved by adjusting the feet: WID TH OF ALL P ANELS Measure A ( the width between adjacent door/drawer fr onts) and write it in the rst box below , then complete the equation.
9 7 CA VITY PREP ARA TION W ater Connection Recommended COLD (Maximum 60°C ). ¾ “ BSP (GB20) to suit flat washer . Kosher requir ements Drains will need to be separated to satisfy kosher requirements . W e suggest you c onfirm acceptability with your local rabbi in respect to kosher installations.
10 8 MAXIMUM DIST ANCE OF HOSES & CORD FR OM CHASSIS EDGE Drain hoses - 1800 mm Inlet hose - 1250 mm Power cord (excl. plug ) - 1650 mm Drain hoses - 2000 mm Inlet hose - 1650 mm Power cord (excl.
11 10a 9a A TT ACH SIDE MOUNTING BRA CKETS PULL THROUGH HOSE S & PUSH INT O THE CA VITY (x2) As you push product in, pull through hoses and co rd, ensuring they don ’t get kinked or twisted.
12 13a FIT THE SUPPLIED T OEKICK P ANEL (OPTIONAL FOR INTEGRA TED MODELS) 3 4 6 8 5 7 9 1 2 19 19 Impor tant! Do not overtighten screw. Where the toekick meets the bottom of the tub is the cut-off point Mark this point on the toekick with a pencil Lay the toekick face down on a chopping board or similiar Smooth the edge with a file.
13 10b REMO VE THE L OWER DRA WER 100 mm 2 4 5 1 100 mm T o prevent kinked hoses, we rec ommend rotating the drawer anti-clockwise and resting it on its side after removal. Press the r elease tabs in on either side and push back to release drawer from runners .
14 x4 13b REFIT THE DRA WER ONTO THE RUNNER S 2 1 4 5 3 Before r efitting the drawer , ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing for ward. Ensure the release tabs on both sides are reset fully . Ensure the drawer is now rotated clockwise back.
15 14b FIT THE SUPPLIED T OEKICK P ANEL (OPTIONAL FOR INTEGRA TED MODELS) 3 4 6 8 5 7 9 1 2 19 19 Impor tant! Do not overtighten screw. Where the toekick meets the bottom of the tub is the cut-off point Mark this point on the toekick with a pencil Lay the toekick face down on a chopping board or similiar Smooth the edge with a file.
16 3 1 1 2 INTE GRA TED MODELS WITH REMOTE (NZ A U) ONL Y - INST ALLING THE FR ONT P ANELS REMO VE BRA CKETS FROM PRODUCT A T T A CH P ANELS TO PR ODUCT EAR TH THE P ANELS A T T A CH P ANELS TO P ANEL.
17 INTE GRA TED MODELS WITH REMOTE (NZ A U) ONL Y - INST ALLING THE FR ONT P ANELS ADJUS T P ANEL HEIGHT TO ALIGN THE CABINETR Y GAPS FITTING A CUST OM T OEKICK P ANEL 19a 20a Y ou can optionally glue.
18 1 2 3 16 mm x6 INTE GRA TED MODELS WITH BADGE (GB IE) ONL Y - INST ALLING THE FRONT P ANELS & BADGE C ONTROLS DETERMINE BADGE CUT OUT L OCA TIONS ROUTE B ADGE WIRING THROUGH P ANEL A T T A CH P.
19 INTE GRA TED MODELS WITH BADGE (GB IE) ONL Y - INST ALLING THE FRONT P ANELS & BADGE C ONTROLS 2 2 1 REA TT ACH B ADGE S & E AR TH THE P ANELS A T T A CH P ANELS TO PR ODUCT ADJUS T P ANEL HEIGHT TO ALIGN THE CABINETR Y GAPS FITTING A CUST OM T OEKICK P ANEL 19b 21b 22b 20b Push the panel in then up to locate.
20 THERE ARE TWO DIFFERENT PL UMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUIT ABLE. 23 3 1 750-882.5 mm 2 * 1 2 38 mm max. 120 mm 750-882.5 mm * If space is limited for fixing, push hose throug.
21 27 26 FINAL CHE CKLIS T TROUBLE SHOO TING Check all par ts are installed . Ensure that all panels and parts thereof are secure and final electrical tests hav e been conducted in accordanc e with local electrical regulations. Ensure product is level , securely fastened t o the cabinetry and opens and closes freely .
An important point after buying a device Fisher & Paykel DD60D 7 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fisher & Paykel DD60D 7 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fisher & Paykel DD60D 7 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fisher & Paykel DD60D 7 you will learn all the available features of the product, as well as information on its operation. The information that you get Fisher & Paykel DD60D 7 will certainly help you make a decision on the purchase.
If you already are a holder of Fisher & Paykel DD60D 7, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fisher & Paykel DD60D 7.
However, one of the most important roles played by the user manual is to help in solving problems with Fisher & Paykel DD60D 7. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fisher & Paykel DD60D 7 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
